Minneapolis, MN 55440 Phone: (800) 553--8033 or (763) 513--2850 www.nobles.com Nobles, the Nobles logo and Power Eagle are registered United States trademarks of Tennant Company. Specifications and parts are subject to change without notice. Copyright E1999, 2000, 2005 Tennant Company. All rights reserved.
OPERATION SAFETY PRECAUTIONS The following information signals potentially dangerous conditions to the operator or equipment: This machine is intended for commercial use. It is FOR SAFETY: designed exclusively to clean carpet and upholstery in an indoor environment and is not 1.
OPERATION 5. When servicing machine: GROUNDING INSTRUCTIONS Unplug cord from wall outlet. Avoid moving parts. Do not wear loose Machine must be grounded. If it should jackets, shirts, or sleeves. malfunction or breakdown, grounding provides a Use manufacturer supplied or approved path of least resistance for electrical current to replacement parts.
OPERATION SAFETY LABELS The safety label appears on the machine in the location indicated. Replace label if it is missing or becomes damaged or illegible. WARNING LABEL - - Located on back of control console. Power Eaglet 716 (08- -05)
OPERATION MACHINE SETUP MACHINE OPERATION FOR SAFETY: Do not operate machine unless 1. Carefully check carton for signs of damage. operator manual is read and understood. Report damages at once to carrier. The machine is shipped fully assembled and is ready for WARNING: Fire Or Explosion Hazard.
OPERATION CLEANING CARPETS WHILE OPERATING 1. Turn on Master switch (Figure 3). 1. If necessary, adjust brush height to accommodate type of carpet (See ADJUSTING BRUSH HEIGHT). 2. Work away from wall outlet and power cord to prevent cord damage. 3.
OPERATION 5. After cleaning, perform the daily maintenance procedures. ADJUSTING BRUSH HEIGHT NOTE: Allow up to one hour for carpet to dry. Use air movers to reduce drying time. 1. Turn off machine and unplug power cord from wall outlet. OPERATING ACCESSORY TOOLS (OPTIONAL) WARNING: Electrical Hazard.
OPERATION 2. Pull valve T--handle to empty dirty water (Figure 10). DAILY MAINTENANCE (After Every Use) 1. Drain and rinse out tanks thoroughly (See Draining Tanks). 2. Rinse out recovery tank and recovery dome thoroughly after every use. 3. Remove vacuum screen and clean (Figure 12). FIG.
OPERATION MONTHLY MAINTENANCE STORING MACHINE (Every 80 Hours of Use) 1. Flush pump system with an acetic acid solution to 1. Before storing machine, be certain to flush tanks dissolve normal alkaline chemical buildup. Follow and drain machine of all water. instructions below: 2.
OPERATION TROUBLE SHOOTING PROBLEM CAUSE SOLUTION Machine does not operate. Faulty switches or wiring. Contact Service Center. Faulty power cord. Contact Service Center. Building circuit breaker tripped. Reset breaker. Solution pump does not operate. Overheated pump. Determine cause and wait 20 minutes for pump to cool.
OPERATION SPECIFICATIONS Model Power Eaglet 716 LENGTH 991 mm (39 in) WIDTH 406 mm (16 in) HEIGHT 864 mm (34 in) WEIGHT 39 Kg (86lb) SOLUTION TANK CAPACITY 31L (7 gal) RECOVERY TANK CAPACITY 31L (7 gal) CLEANING PATH WIDTH 406 mm (16 in) MAXIMUM CLEANING RATE 186 m...
PARTS LIST CHASSIS GROUP Power Eaglet 716 (08--05)
Page 21
PARTS LIST CHASSIS GROUP PART # DESCRIPTION QTY. PART # DESCRIPTION QTY. 613481 HOSE, 3/8ID X 5/8OD X 11” 180628 DSCREEN, SOLUTION TANK 0.916 LP GRAY (160207) 150403 ELBOW, 45_ 613508 HOSE GUARD 9.70” CLEAR 0.809 150415 ELBOW, 90_ NYL 1/4 MPT X 3/8 (160210) 613474 HOSE, 3/8ID X 5/8OD X 3”...
Need help?
Do you have a question about the Power Eagle 716 608543 and is the answer not in the manual?
Questions and answers