Swash・Mixing 【Swash・Mix - JR XG 14 Operation Manual

Function▋List Function▋List
▋Swash▋Mixing 【SWASH▋MIX】
▋Function▋Explanation
▋
This function sets the mixing relating to the swash plate and swash plate servos (1-4) to allow
coordinated control of the helicopter. This swash mixing is essential for helicopters that incorporate CCPM
systems. CCPM is a type of pitch mixing in which the servos are directly linked to the swash plate. In this
transmitter, 7 types of swash plates can be selected. Match the "SWASH TYPE" in the System List with your
helicopters servo configuration. An E-ring function is also incorporated that easily limits the swash maximum
angle.
▋Setting▋Method
▋
Set the "SWASH TYPE" according to the helicopter's swash plate configuration. The "SWASH TYPE" selection is
in the System List, and should be chosen before proceeding to set the swash mix.
The default settings for the
Sw a sh M i x a r e + 6 0 % on
Aileron, Elevator and Pitch.
I f n e c e s s a r y, a dj u s t t h e
mixing amount according to
the type of helicopter and
servo setup. Press the dial
to display the setting box,
and then set the direction
a nd t he nu mer ic a l va lue
adjustment.
⿟ Exponential Function (EXP)
By activating this function, the servo's non-linear output is modified to be more linear in motion.
⿟ E-Ring Function (E-RING)
By activating this function, the e-ring electronically
corrects the swash to move in the same angle in all
directions. The operation of the stick and e-ring can be
confirmed on the graph. The diameter of the circle is
the swash tilt angle, which can be set as desired.
⿟ Correction mixing
፧ PIT->AILE,->ELEV
This mix corrects tilt of the swashplate in the aileron
and elevator axis when the pitch stick is moved up and down. Adjustment of the mixing amount can be carried
out separately to the front and rear and to the left and right. The mix can be switched ON and OFF of using a
switch or flight modes as desired.
፧ AILE->ELEV、ELEV->AILE
This is used to correct interactions where
aileron and elevator movement influence
each other. The aileron and elevator mutual
mixing amount can be separately adjusted.
The switching ON/OFF of the mixing on
this screen can be set using a switch or
flight modes as desired. It is also possible
to use TR IM INPUT to adjust the mix
during flight using a trim lever.
⿟ Trim Input Function (TRIM IN)
By using the Trim Input, it is possible to change the mix values using the Trim Lever. Therefore, it is possible to
easily adjust the mix during flight.
TIPS
⿟ If the servo direction is incorrect, it is possible to set the mixing amount in a negative direction to achieve an
appropriate setting.
⿟ The setting value in this function should be between 0 to ± 125. If the mixing amount is too much and you are
not able to achieve the desire servo throw, adjust the servo horn hole position (with a practical range of 40-
70%) outwards to have more throw.
▋Caution▋Note
▋
⿟ Actually operate the servos and carefully confirm the settings before flying.
Swash type
Swash type
Swash type
調整ポイント表示
現在の
フライトモード位置
各調整ポイントの
入力位置と出力位置
ポイントの
追加と削除
ポイント接続を曲線に変更
Correction mixing
Correction mixing
Correction mixing
35
カーブをコピー
Mixing amount
Mixing amount
スティック入力位置と出力位置の数値表示
Mixing amount
E-Ring Function
E-Ring Function
ダイヤル
E-Ring Function
CAUTION
Helicopter
Airplane
Glider
Exponential Function
Exponential Function
Exponential Function
注意：
グラフはホバリン
グスロットルやス
ロットルトリムで
変化する場合もあ
ります。