Summary of Contents for Vision Fitness T9800 Series
Page 1
O w n e r’s G u i d e T9800 Series TREADMILLS...
Page 4
VISION FITNESS T9800 Treadmill. You’ve taken an important step in offering your customers what they need to achieve their fitness goals with a Treadmill that is designed specifically to meet your facility’s needs. It is important to have complete knowledge of this piece of equipment before use.
Table of Contents CONSOLE A L L M O D E L S T 9 8 0 0 H R T SAFETY INSTRUCTIONS ..4 CHOOSING PROGRAM & AGE ..17 POWER REQUIREMENTS .
Page 7
CONSOLE HANDLEBARS SIDE RAILS RUNNING BELT MOTOR COVER LEVELERS TRANSPORT WHEELS T 9 8 0 0 S T 9 8 0 0 H R T P L AT F O R M T R E A D M I L L S...
Unplug your VISION FITNESS Treadmill before moving it. CHILDREN • Keep children off of your VISION FITNESS Treadmill at all times. • When the VISION FITNESS Treadmill is in use, young children and pets should be kept at least 10 feet away.
POWER REQUIREMENTS This product is intended for use on a nominal 120-volt electrical circuit. This product is equipped with a NEMA 5-20P plug (illustrated below). Be sure the product is connected to an outlet with the same configuration (also shown below).
MOVING YOUR VISION FITNESS TREADMILL Your VISION FITNESS Treadmill has a pair of transport wheels built into the front legs. To move, firmly grasp the back end of the frame, carefully lift and roll. CAUTION: Our Treadmills are well-built and heavy, weighing up to 355 pounds! Use care and additional help if necessary.
Treadmill will come to a stop. To resume your workout, you will need to re-enter any data. SAFETY MAGNET KEY & CLIP Your VISION FITNESS Treadmill will not start unless the Safety Magnet Key is inserted into the circle in the console overlay. You should attach the clip end to your clothing.
T9800S & T9800HRT FEEDBACK DISPLAY ALPHANUMERIC MESSAGE CENTER This is a display that will scroll the operation instructions in the top center display window. It will also display your feedback when the LED next to the appropriate word is lit. CALORIES Shown as estimated calories burned during workout.
Page 13
T9800S & T9800HRT FEEDBACK DISPLAY HEART RATE Shown as beats-per-minute. You can monitor your heart rate at any time during a workout by using a wireless chest transmitter or gripping the hand pulse heart rate sensors on the front handlebar. AVG HEART RATE Displays percentage of maximum heart rate.
Page 14
T9800S & T9800HRT FEEDBACK DISPLAY PROFILE MATRIX WINDOW The left dots will show an Elevation profile in six segments in ORANGE. This profile is not an exact representation of the elevation profile, but just a bar graph. The profile will scroll to the left during operation. The right dots will show a Speed profile in six segments in RED.
Page 15
T9800S & T9800HRT FEEDBACK DISPLAY SPB-SEGMENT PROGRESS BAR The center two columns on the dot matrix are the SPB (Segment Progress Bar). These two bars represent the accumulated time per segment. Each program has 20 segments. The SPB takes the segment time and divides it into 10 vertical dots.
T9800S & T9800HRT FEATURES USER LOG-IN The T9800S and T9800HRT consoles have a special feature that allows you to log-in and save all data from your workout. To use this function, follow these steps: PRESS LOG-IN BUTTON Use either set of arrow keys to choose a user I.D.
T9800S & T9800HRT FEATURES WORKOUT TOTALS To use this function, you will need to use the same user I.D. number code and follow these three steps: PRESS WORKOUT TOTALS BUTTON Use either set of arrow keys to enter your user I.D. number. This is the same number that you use to log-in before you begin working out.
T9800S & T9800HRT FEATURES QUICK SPEED AND QUICK ELEVATION KEYS Use the QUICK SPEED and QUICK ELEVATION keys as an option to increase and decrease the speed and elevation to your desired setting. First press the QUICK SPEED or QUICK ELEVATION key, then press the numbered keys (0-9).
CONTACT HEART RATE HAND PULSE HEART RATE SENSORS The Contact Hand Pulse Sensors are included on this product to monitor your heart rate. To use, grasp both of the sensors with a comfortable grip during your workout. The console will display your heart rate. NOTE: For the Heart Rate Training programs, you must use a chest transmitter (not included).
INTRODUCTION TO T9800S EASY START To start the T9800S , simply press START; the Treadmill will start and time will count up. Press ENTER to set age, time, and weight. ENTER AGE Set your age using the number keys or either set of arrow keys.
T9800HRT FEATURES PROGRAM QUICK KEYS We have made choosing a program simple and easy with our program Quick Key feature. All you need to do is select one of the keys and you are on your way. The SPRINT 8 key takes you directly to that program.
T9800HRT FEATURES CHOOSING A LEVEL Choose level using the number keys or arrow keys, and press ENTER. The elevation and speed windows will display the program’s maximum elevation and speed. The Message Center will also display “LEVEL1,” etc. PROGRAM LEVELS Most programs have 10 levels, and SPRINT 8 has 17 levels.
CHOOSING A TIME CALORIES DISTANCE TIME HEART RATE Choose time using the number PACE AVG. SPEED AVG. PACE % HEART RATE keys or either set of arrow keys, and press ENTER. ELEVATION SPEED QUICK QUICK ELEVATION SPEED START STOP ENTER PRESS FOR EASY START HOLD TO RESET HOLD TO SCAN...
T9800HRT PROGRAM DETAILS SPRINT 8 • SPEED AND ELEVATION CHANGES SPRINT 8 is an anaerobically-based interval program. It is effective in recruiting fast twitch muscle fibers and improving athletic performance. Medical research supports that this type of exercise will help combat somatopause, which inflicts adults in middle-age and is signified by weight gain, muscle loss, wrinkled skin, and lack of energy.
USING THE SPRINT 8 PROGRAM The SPRINT 8 program is an anaerobic interval program designed to build muscle, improve speed, and naturally increase the release of Human Growth Hormone (HGH) in your body. Producing HGH through exercise and a proper diet has been shown as an effective way to burn fat and build lean muscle mass according to Phil Campbell, author of Ready, Set, Go! Synergy Fitness.
T9800HRT PACER PROGRAM DETAILS This is a motivational program that allows you to race against the console. You determine the speed of the pacer and the distance of the workout. You control you own speed and elevation throughout the program. The top row of dots is the pacer.
T9800HRT HEART RATE TRAINING NOTE: A CHEST TRANSMITTER IS NEEDED TO USE THE HEART RATE PROGRAMS WEIGHT LOSS • ELEVATION ONLY ® (65% OF PREDICTED MAXIMUM HEART RATE) Program default is 30 minutes The HRT WEIGHT LOSS program is designed to maintain you at 65% of ®...
Page 28
ENTER AGE Set your age using the number keys or either set of arrow keys. Press ENTER. Your age is used to determine your predicted maximum heart rate. ENTER TARGET HEART RATE You can change the target heart rate by using the number keys or either set of arrow keys.
Page 29
ENTERING YOUR WEIGHT CALORIES DISTANCE TIME HEART RATE Enter weight using the number PACE AVG. SPEED AVG. PACE % HEART RATE keys or either set of arrow keys. The Message Center window will display the weight. Press ENTER. ELEVATION SPEED Press START to begin.
Page 30
COOL-DOWN MODE After you have completed your timed workout, the console will display: “COOL DOWN.” This is to let you know that your program has ended. You are now in a manual mode cool-down and have control of the speed and elevation.
T9800HRT ENDURANCE • SPEED AND ELEVATION ® Program default is 30 minutes. (Program time does not begin until target heart rate is achieved.) The Treadmill has a manual mode warm-up until you reach your target heart rate. During the warm-up mode, you control both speed and elevation.
Page 32
ENTER TARGET HEART RATE (See Page 35 to determine your recommended target heart rate.) Using the number keys or either set of arrow keys, enter your target heart rate and press ENTER. CHOOSE PROGRAM TIME Set the time using the number keys or either set of arrow keys.
Page 33
WARM-UP MODE Now the Treadmill is in the manual warm-up mode. You are now in control of both the speed and elevation to reach your target heart rate zone. Once a steady heart rate within 3 beats per – minute of your entered target zone is found, the console will beep and then enter the heart rate training mode.
Page 34
COOL-DOWN MODE After you have completed your timed workout, the console will display: “COOL DOWN.” This is to let you know that your program has ended. You are now in a manual mode cool-down and have control of the speed and elevation.
T9800HRT INTERVAL • SPEED ONLY ® Program default is 30 minutes. (Program time does not begin until 85% of target heart rate is achieved.) The HRT INTERVAL has a manual warm-up mode until you reach 85% of ® your target heart rate. During this warm-up, you control both speed and elevation.
Page 36
ENTER AGE Set your age using either set of arrow keys. Press ENTER. Your age is used to determine your predicted maximum heart rate. ENTER TARGET HEART RATE (See Page 35 to determine your recommended target heart rate.) Using the number keys or either set of arrow keys, enter your target heart rate.
Page 37
ENTERING YOUR WEIGHT CALORIES DISTANCE TIME HEART RATE Enter weight using the number keys PACE AVG. SPEED AVG. PACE % HEART RATE or either set of arrow keys, and press ENTER. The Alphanumeric Message Center window will display the ELEVATION SPEED weight.
Page 38
COOL-DOWN MODE After you have completed your timed workout, the console will display: “COOL DOWN.” This is to let you know that your program has ended. You are now in a manual mode cool-down and have control of the speed and elevation.
GENERAL HEART RATE TRAINING RECOMMENDATIONS To use the Heart Rate Training Program, it is important to determine your target heart rate using the chart below. After determining your target rate, you should use the Treadmill in MANUAL mode to see if the target you have selected is correct.
RATE OF PERCEIVED EXERTION Rate of Perceived Exertion (R.P.E.) is one of the easiest ways to monitor exercise intensity. By becoming familiar with the RPE scale, you can continually assess your level of intensity and insure a level of exertion that is comfortable.
USING A WIRELESS CHEST TRANSMITTER (NOT INCLUDED) Center the Transmitter Strap just below the breast or pectoral muscles, directly over your sternum with the logo facing out. Adjust the elastic strap length to avoid bouncing or sliding.
CUSTOM PROGRAMS 1-5 Design your own programs by setting the desired time, speed, and elevation of 20 different segments. By designing your own programs, you now can control your fitness goals workout by workout. This allows you to modify your training based on certain events or milestones you may have set for yourself.
Page 43
PRESS ENTER TO PROGRAM ENTER SEGMENT TIME Modify the segment number using the elevation arrows and the segment time using the speed arrows. Press ENTER. ENTER SEGMENT SPEED AND ELEVATION The #1 column will blink. Press the number keys and/or the SPEED arrow keys to change the speed segment column (Speed numeric values changing with red column).
Page 44
SAVING SEGMENT DATA Press the ENTER key to store Speed and Elevation, then proceed to the next column. NOTE: Repeat entering segment time, speed, and segment elevation until all 20 segments are completed. BEGINNING WORKOUT Begin exercising in your new custom program by pressing the START button.
USER ENGINEERING MODE Your Treadmill offers a User Engineering Mode that can access certain data and help to troubleshoot your Treadmill. User Engineering Mode is designed for you to access functions that will not affect important Treadmill settings. To access this mode please hold down SPEED DOWN and ENTER for 5 seconds while the Treadmill is in any state of setting up a program.
Page 47
USER ENGINEERING MODE (continued) DEFAULT AGE The default age is 40. You can modify the default age using the speed arrow keys. Press ENTER to save. DEFAULT WEIGHT Default weight is 150 lbs/ 68kg. You can modify the weight by using the speed arrow keys.
USER ENGINEERING MODE (continued) AUTO-CALIBRATION DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION! To begin auto-calibration, press ENTER. The Treadmill will run through minimum and maximum speed and maximum incline; this will take 3-5 minutes. Let the Treadmill perform this complete function before exiting the User Engineering Mode.
Page 49
USER ENGINEERING MODE (continued) LUBRICATE DECK MESSAGE This is a service message that will appear on the console. Use the speed arrows to turn this message On or Off. Press ENTER to save. CLEAN TREADMILL This is a service message that will appear on the console. Use the speed arrows to turn this message On or Off.
SOLUTION: The lubricating wax coating on the deck is wearing down and needs to be replenished; contact your VISION FITNESS retailer. PROBLEM: The Treadmill shuts off when elevated. SOLUTION: Check to make sure that the power cord is not stretched so tight that when the Treadmill is elevated the cord is pulled out of the wall outlet.
Page 51
TROUBLESHOOTING YOUR HEART RATE MONITOR CHEST STRAP PROBLEM: No pulse reading appears. SOLUTION: There may be a poor connection between the contact pads and skin. Remoisten electrodes. SOLUTION: Transmitter is not properly positioned. Reposition the chest strap. SOLUTION: Verify that the distance between transmitter and receiver is not beyond the recommended range of 36 inches.
TENSIONING THE BELT If the running belt slips when used, use the supplied 8mm Allen wrench to turn the left and right tension bolts clockwise -turn at a time until the belt no longer slips. CENTERING THE BELT Run the treadmill at 2.0 mph. If the running belt is too far to the right side, use the supplied 8mm Allen wrench to turn the right tension bolt clockwise -turn at a time until the belt remains centered during use.
PREVENTIVE MAINTENANCE Following are several tips on taking care of your VISION FITNESS Treadmill. The location of your Treadmill is important in maintaining it properly. Find a location that does not accumulate dust and dirt easily. A clean environment can help to prolong the life and improve the performance of your treadmill.
COMMERCIAL MAINTENANCE FOR BEST PERFORMANCE WE RECOMMEND THE FOLLOWING MAINTENANCE SCHEDULE: I T E M WEEKLY MONTHLY QUARTERLY ANNUALLY INSPECT CONSOLE BOLTS FRAME CLEAN INSPECT RUNNING BELT CLEAN INSPECT DECK** CLEAN INSPECT (VACUUM) POWER CORD INSPECT CLEAN INSPECT CONSOLE BOTTLE HOLDERS CLEAN HANDLEBARS CLEAN...
HOME MAINTENANCE PREVENTIVE MAINTENANCE Following are several tips on taking care of your VISION FITNESS Treadmill. The location of your Treadmill is important in maintaining it properly. Find a location that does not accumulate dust and dirt easily. A clean environment can help to prolong the life and improve the performance of your Treadmill.
MOTOR - FIVE YEARS VISION FITNESS warrants the Motor against defects in workmanship and materials for a period of five years from date of original purchase, so long as the device remains in the possession of the original owner.
Page 57
WARRANTY REGISTRATION Your warranty card must be completed and sent to VISION FITNESS before a warranty claim can be processed. You may also register via our website at www.visionfitness.com. Inside the enclosed warranty card you will find a customer survey.
LABOR - TWO YEARS VISION FITNESS shall cover the Labor cost for the repair of the device for a period of two years from the date of original purchase, so long...
Page 59
WARRANTY REGISTRATION Your warranty card must be completed and sent to VISION FITNESS before a warranty claim can be processed. You may also register via our website at www.visionfitness.com. Inside the enclosed warranty card you will find a customer survey.