Download Print this page

Explanation Of General View; Specifications - Makita 1051D Instruction Manual

Cordless power planer
Hide thumbs

Advertisement

ENGLISH
1
Button
2
Battery cartridge
3
Knob
4
Scale
5
Pointer
6
Lock-off button
7
Switch trigger
8
Start
9
End
10 Washer

SPECIFICATIONS

Model
Capacities
Planing width ..................................................... 50 mm
Planing depth .................................................... 0.5 mm
Shiplapping (rabbeting) depth ........................... 15 mm
-1
No load speed (min
) ............................................. 9,000
Overall length ..................................................... 297 mm
Net weight ...............................................................2.2 kg
Rated voltage .................................................D.C. 14.4 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for planing wood.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.

Explanation of general view

11 Thumb screw (A)
12 Edge fence (Guide rule)
13 Thumb screw (B)
14 Blade edge
15 Side of drum
16 Cutting line
17 "V" groove
18 Front base
19 Align "V" groove with edge of
workpiece
7.
1051D
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.
ADDITIONAL SAFETY RULES FOR TOOL
ENC004-1
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Wait until the blade attains full speed before cut-
11. Keep at least 200 mm away from the tool at all
12. Always switch off and wait for the blades to
20 Dust bag
21 Nozzle
22 Fastener
23 Installation bolts
24 Hex wrench
25 Loosen (counterclockwise)
26 Planer blade
27 Drum
28 Drum cover
29 Pan head screws
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
Rags, cloth, cord, string and the like should
never be left around the work area.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Use only sharp blades. Handle the blades very
carefully.
Be sure the blade installation bolts are securely
tightened before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
Make sure the blade is not contacting the work-
piece before the switch is turned on.
ting.
times.
come to a complete stop before any adjusting.
ENB043-1
5

Advertisement

loading

  Related Manuals for Makita 1051D