Page of 12

Makita 1002BA Instruction Manual

110 mm (4-3/8") curved planer.
Hide thumbs

Advertisement

Curved Planer
Planing width
110 mm (4-3/8")
1 I O mm (4-3/8") MODEL 1002BA
Planing depth
No load speed
Overall length
Net weight
4 mm (5/32")
15,000
339 mm (13-1/32")
5 4 kg (1 1 9 Ibs)
(RPM)
INSTRUCTION MANUAL

Advertisement

   Related Manuals for Makita 1002BA

   Summary of Contents for Makita 1002BA

  • Page 1

    Curved Planer 1 I O mm (4-3/8") MODEL 1002BA INSTRUCTION MANUAL Planing depth Planing width No load speed Overall length Net weight (RPM) 110 mm (4-3/8") 4 mm (5/32") 15,000 5 4 kg (1 1 9 Ibs) 339 mm (13-1/32")

  • Page 2

    SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.

  • Page 3

    REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turn- ing it on. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. EXTENSION CORDS.

  • Page 4

    Clean out chips with a stick. 13. Do not leave the tool running. Operate the tool only when hand-held. 14. When leaving the planer, switch wooden block, so that the blades do not contact anything. 15. Always change both blades or covers on the drum, otherwise the result- ing imbalance will cause vibration and shorten tool life.

  • Page 5

    Removing or installing planer blades CAUTION: Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blades on the drum, un- screw the four installation bolts with the socket wrench. The drum cover comes off together with the blades.

  • Page 6

    Adjusting depth of cut Depth cut may be adjusted by simply turning the knob on the front Adjusting front base The front base is factory-adjusted to allow concave cuts with a radius concave cuts with the tool’s minimum radius of 300 mm, loosen the wing bolt on either side and raise the front base as far as it will go.

  • Page 7

    Sharpening planer blades Always keep your blades sharp performance possible. Use the sharpening holder to remove nicks and produce a fine edge. First, loosen the two wing nuts on the holder and insert the blades (A) and (B), so that they contact the sides Then tighten the wing nuts.

  • Page 8

    To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjust- ment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Limit mark...

  • Page 9

    ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner...

  • Page 10

    Seo.-ll-'97 (4-318") 110 mm CURVED PLANER Model 1002BA Note: The switch and other part configurations may differ from country to country.

  • Page 11

    MODEL 1002BA ,&, DESCRIPTION MACHINE Pan Head Screw M4x50 Pan Head Screw M4x20 Chtp Cover Brush Holder Cap Carbon Brush Wing Bolt M6x25 Spring Washer Flat Washer 6 Rivet 0 - 5 Name Plate Main Frame Cord Cord Guard Strain Relief...

  • Page 12

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.

Comments to this Manuals

Symbols: 0
Latest comments: