Kenwood TK-390 Service Manual page 14

3-3. Group Setting Mode
Set data for each Group while in this mode. After first
entering Self programming mode, select the "GROUP" dis-
play with [Top 1] [Top 2] and press [PTT] to set Group Set-
ting mode. Once in Group Setting mode, select the group
that needs setting with the [Top 1] [Top 2] keys and press
[PTT]. Next select the channel for setting with the [Top 1]
[Top 2] keys and press [PTT]. The setting items and setting
data will then appear so reset the data with the [Top 1]
[Top 2] keys and press [PTT]. When finished, the display
shifts to the next setting item. After finished setting all
items press [PTT] to return to next Group selection.
No. Function name Display
Select Group GRP 1
1 Battery save BATT L
2 Time out timer TOT 60
3 TOT pre alert TOT.P 10
4 TOT rekey time TOT.K 2
5 TOT reset time TOT.S 2
6 Group Delete/Add D/A ADD
7 Signalling SIG AND
• Operation
1. Select the setting value with the [Top 1] [Top 2] keys.
2. Press the [PTT] and the selected value is backed up and
operation shifts to the next item for setting.
3. Press [Side 2] on the Group selection screen in order to
return to the Self programming mode initial display.
• Note
1. Different sample displays are shown.
2. Setting item No.s are displayed with a 7-segment 2-digit
figure on the LCD.
3. Self programming mode cannot be set when set to Dis-
able with the FPU.
• Flow Chart
Self programming mode
Group setting mode
Group selection
[Side 2]
1. Battery save
[Side 2]
2. Time out timer (TOT)
[Side 2]
3. TOT pre-alert
[Side 2]
4. TOT rekey time
[Side 2]
5. TOT reset time
[Side 2]
6. Scan group Delete/Add
[Side 2]
7. Signalling AND/OR
[Side 2]
[Side 2]
REALIGNMENT
Remarks
1~160
OFF, Short, Mid, Long
OFF, 30s~300s (30s step)
OFF, 1s~10s (1s step)
OFF, 1s~60s (1s setp)
OFF, 1s~15s (1s step)
Delete, Add
AND, OR
[Top 1] [Top 2]
[PTT]
[PTT]
[PTT]
[PTT]
[PTT]
[PTT]
[PTT]
[PTT]
[PTT]
3-4. Function Setting Mode
This mode allows making function settings for the trans-
ceiver. After first entering Self programming mode, select
"FUNC" display with [Top 1] [Top 2] and then press [PTT] to
set this mode. Function setting items are listed below.
No. Function name
1 Power on tone POW.T 15 (or C)
2 Control tone CON.T 15 (or C)
3 Warning tone WAR.T 15 (or C)
4 Alert tone ALR.T 15 (or C)
5 Minimum volume MIN.V 8
6 Battery warning BATT ON
7 Busy LED B.LED ON
8 TX LED T.LED ON
9 Invert Display LCD ON
10 Priority 1 P1 NONE
11 Priority 1 group 1.–1
12 Priority 1 channel 1–1.
13 Priority 2 P2 NONE
14 Priority 2 group 1.–1
15 Priority 2 channel 1–1.
16 Revert channel REVT 1
17 Squelch level SQ.LV 15
• Operation
1. Select the setting value with the [Top 1] [Top 2] keys.
2. Press the [PTT] and the selected value is backed up and
operation shifts to the next item for setting.
3. Press [Side 2] on the Group selection screen in order to
return to the Self programming mode initial display.
• Note
1. Different sample displays are shown.
2. Setting item No.s are displayed with a 7-segment 2-digit
figure on the LCD.
3. Self programming mode cannot be set when set to Dis-
able with the FPU.
TK-390
Display Remarks
Continuas, 0~31
Continuas, 0~31
Continuas, 0~31
Continuas, 0~31
0~31
Disable, Enable
OFF, ON
OFF, ON
Disabel, Enable
None, Selected, Fixed
1–1~10–16
(Priority 1= In fixed)
None, Selected, Fixed
1–1~10–16
(Priority 2= In fixed)
1~8
1 : Selected
2 : Last called
3 : Last used
4 : Sel+Talk back
5 : Priority 1
6 : Priority 1+Talk back
7 : Priority 2
8 : Priority 2+Talk back
0~15
13