Siemens C25 Service Manual
Hide thumbs Also See for C25:

Advertisement

Service Manual
Service Manual C25 / C2588
Sm_C25_lvl2_v10_w97
for
C25 / C2588
V 1.0
V 1.0
Page 1 of 32
Private Communication Systems
Mobile Phones
ICP CD ST
R. Fleuren
02/99

Advertisement

Table of Contents
loading

Summary of Contents for Siemens C25

  • Page 1 Private Communication Systems Mobile Phones Service Manual C25 / C2588 V 1.0 V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 1 of 32 02/99...
  • Page 2: Introduction

    C25 and C2588. For information on level 2.5 repairs or on the testequipment, please refer to the available documentation. The repairs for C25 and C2588 are identical unless otherwise noted, and therefor in the text only C25 is mentioned. Attention:...
  • Page 3: Table Of Contents

    EADSET 9.10 ............................31 RADLE 9.11 ..........................31 NTENNA CRADLE 9.12 ............................32 HARGER 9.13 ..........................32 ORTABLE 9.14 ..........................32 OMFORT V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 3 of 32 02/99...
  • Page 4 Private Communication Systems Mobile Phones 9.15 ............................32 ANDSET V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 4 of 32 02/99...
  • Page 5: Technical Data

    Spare Battery, Rapid Charger, Travel Charger, Desk Top Charger, Designer Cases, Belt Clip, Headset, Car Cradle, Antenna cradle, Car Charger; Car Kit Portable, Car Kit Comfort, Car Handset V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 5 of 32...
  • Page 6: General Information

    The mechanical concept of the C25 differs in various points from the one of the other Siemens mobile telephones. The first thing you will experience is how the housing is locked. In C25 no screws are used to keep the housing closed. Also inside the telephone no screws are used anymore.
  • Page 7 (1310) by a metal clip (1190) and electrically connected to the board by a cable and a plug. The ringer in C25 is of the same type as the one used in C1x mobiles. C25 does have an external connector of a new type. Since S6 a so called „Molex“- connector was used, which also offered the possibility to connect an external antenna to it.
  • Page 8: Mechanical Drawing

    Mechanical drawing Note: The numbers shown above are NO ordering numbers. For ordering please use the partnumbers supplied by your service manager! V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 8 of 32 02/99...
  • Page 9: Necessary Tools

    Private Communication Systems Mobile Phones Necessary tools For disassembling the C25 the following Case Opener is mandatory: Ordering number of Case Opener: F30032-P46-A1 Disassembling the C25 Attention: ESD regulations have to be followed! 1. You first remove the battery lid and then the battery below.
  • Page 10 8. After that you disconnect the ringer plug-in connector. 9. You then remove the ringer from the lower HF-screen lid. 10. Remove the clip from the lower HF-screen lid. V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 10 of 32...
  • Page 11 14. Finally, you carefully release the retaining clip (1) of the plug-in connector and pull the connector cable of the display out (2). V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 11 of 32...
  • Page 12: Assembling The C25

    5. Place the clip on the lower HF-screen lid. Attention! The metal projection on the clip must engage with the recess in the screen lid. V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 12 of 32...
  • Page 13 The battery contacts must not be dirty, damaged or bent. 11. Now close the device by putting on the lower housing section. Attention! All catches must engage completely. V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 13 of 32 02/99...
  • Page 14 14. Finally you insert the battery and close the battery compartment with the battery lid. 15. Now you have assembled the phone completely. V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 14 of 32...
  • Page 15: Handset Datecodes

    Private Communication Systems Mobile Phones Handset Datecodes Siemens is using the industrial standard DIN EN 60062 to indicate the production / service dates. The code is printed on the IMEI sticker located in the battery compartment. YY = Datecode • The first character of the datecode indicates the year of production:...
  • Page 16: Hardware Concept

    Private Communication Systems Mobile Phones Hardware Concept Block Diagram V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 16 of 32 02/99...
  • Page 17: Hardware Description

    • Mixer to mix down the RF signal to the Intermediate Frequency (IF) • Programmable IF amplifier with a dynamic range of 60dB ( -10dB ... +50dB in steps of 2dB). V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97...
  • Page 18 This circuit provides the IF synthesizer, the I/Q modulator, prescalers to regulate the RF synthesizer and a buffer stage to feed the PA. The antenna switch is mechanical, located in the connector for the external antenna. V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97...
  • Page 19: Power Supply Concept

    You cannot switch on the handset if the battery voltage is not present. From the battery voltage all other supply voltages of the C25 are derived, controlled by the power supply ASIC. The RF power amplifier needs an operation voltage of 5,4Volts, which is generated by a DC-DC step-up converter.
  • Page 20: Overvoltage Conditions

    ã Be careful with foreign accessories or chargers! ã Make sure that the charging current is limited to a value below 1A! V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 20 of 32 02/99...
  • Page 21: Software Programming

    Bootadapter AC-Adapter The software of the C25 handset is programmed directly from a PC using a bootadapter as an interface between serial port of the PC and the mobile. Because of the new type of external connector used in C25 (Lumberg type) an additional adapter cable between mobile and bootadapter is required.
  • Page 22: Language Groups

    Private Communication Systems Mobile Phones Language Groups For C25/C2588 the following languages will be available. They will be separated into different language groups. Bahasan Indonesia Bahasan Malaysia Catalan Cestina Danish Dutch English Finnish French German Greek Hungar Italian Norsk Polish...
  • Page 23: Battery

    Private Communication Systems Mobile Phones Battery Specification The C25 battery is a NiMH type with a voltage of 3.6Volts and a capacity of 700 mAh. Suppliers are Varta and Maxell. You can easily recognize the manufacturer by the colour of the battery cells: Varta’s cells are of a green colour, Maxell’s ones...
  • Page 24: Charging

    Charging The battery can only be charged if inserted into the telephone. The charging process is completely controlled by the mobile. Different kinds of Siemens chargers out of the accessory program for C25 models can be used for this task: Ø...
  • Page 25: Deep Discharge

    Connect charger to the telephone. The charging symbol will come up as an indication that the normal charging process has been started by the mobile. V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 25 of 32...
  • Page 26: Battery Datecodes

    Private Communication Systems Mobile Phones Battery Datecodes There are two different suppliers of the C25 batteries and they use different kinds of codes to give information about production date: a) Maxell batteries The datecode printed on the battery looks like this:...
  • Page 27: Unblocking

    If you need unblocking codes just send a fax with the IMEI numbers to: Siemens AG PN MP SH World Service Center Bocholt, Germany Fax: +49 2871 91 3007 Please use the appropriate form provided by your Siemens service coordinator. V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97...
  • Page 28: Internet Solution

    IMEI number of the affected handset. The page will then present Master Phone Codes, Master Network Codes and Master Service Provider Codes (if applicable to the relevant telephone). If you do not have access to this tool up to now, please contact your Siemens service manager for details. V 1.0...
  • Page 29: Accessories

    Ø Talk time: up to 5 hours Ø Charging time: Approx. 5 hours with Standard charger Approx. 1.5 hours with Rapid charger V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 29 of 32 02/99...
  • Page 30: Spare Battery

    The desktop charger forms a convenient stand for the mobile. It enables „easy drop in charging“ and connects to all available C25 chargers. Ø Small attractive design fitting to C25 Ø Comfortable charging of the phone Ø Power supply by Rapid Charger, Ø...
  • Page 31: Belt Clip

    Ø Safety supplement for in car use Ø Individual angle positioning Ø Park Position for Car Charger etc. Ø Support privacy functionality V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 31 of 32 02/99...
  • Page 32: Car Charger

    Ø Direct call acceptance by lifting up handset Ø Volume control directly on the handset Ø Curley Cord Ø Plug and play connector to handsfree unit V 1.0 Service Manual C25 / C2588 ICP CD ST R. Fleuren Sm_C25_lvl2_v10_w97 Page 32 of 32 02/99...
  • Page 33 Information and Communication Products Communication Devices C25(88) Level 2.5 Repair Documentation V 1.2 V1.2 Page 1 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 34 The repairs for C25 and C2588 are identical unless otherwise noted. Lately a new version of the C25 has been introduced. This version has the main processor HiGold version 4.3 of the S25(88). Internally this C25 is therefore called C25V4. The level 2.5 parts are identical to the old C25 version.
  • Page 35 Information and Communication Products Communication Devices Table of Contents: INTRODUCTION ............................2 ANTENNA CONNECTOR .......................... 4 RINGER CONNECTOR ..........................8 BOTTOM CONNECTOR (LUMBERG)....................11 18µH COIL ..............................14 ANTENNA SPRING ........................... 18 DISPLAY CONNECTOR........................... 21 DISPLAY CAPACITORS .......................... 25 RINGER COIL............................29 KEYPAD LEDS............................
  • Page 36: Antenna Connector

    Information and Communication Products Communication Devices 2 Antenna Connector Affected Units 2.1.1 Type: 2.1.2 Affected IMEIs / Date Codes: All / All 2.1.3 Affected SW-Versions: 2.1.4 Fault Code for LSO reporting: 3ANC Fault Description 2.2.1 Fault Symptoms for customers: Network Search when using the external antenna (carkit) No location update possible on external antenna (carkit) 2.2.2 Fault Symptom on GSM-Tester:...
  • Page 37 Information and Communication Products Communication Devices From Power To / From Amplifier/ Internal To Receiver Antenna Priority: ..Mandatory ..Repair ..Optional ..Not Yet Defined Repair Documentation 2.4.1 Description of procedure: 2.4.1.1 Diagnosis Check the output power of the handset with the LSO testprogram. Especially watch the external antenna power! 2.4.1.2 Repair by component change Use hot air blower to remove defective connector...
  • Page 38 Communication Devices 2.4.1.3 Repair by SW-Booting Not possible! 2.4.1.4 Test Retest handset after repair as described above. 2.4.2 List of needed material 2.4.2.1 Components C25 antenna connector Part-Number: L36334-Z93-C261 2.4.2.2 Jigs and Tools Hot Air Blower Soldering Iron 2.4.2.3 Special Tools None 2.4.2.4 Working materials...
  • Page 39 Information and Communication Products Communication Devices 2.4.3 Drawings Figure 1: C25 Board Antenna Connector Side (Top View) Figure 2: C25 Antenna Connector Placement (X400) (Top View) V1.2 Page 7 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 40: Ringer Connector

    Information and Communication Products Communication Devices 3 Ringer Connector Affected Units 3.1.1 Type: 3.1.2 Affected IMEIs / Date Codes: All / All 3.1.3 Affected SW-Versions: 3.1.4 Fault Code for LSO reporting: 3RIC Fault Description 3.2.1 Fault Symptoms for customers: Problems with the handset ringer. No ringer tone audible.
  • Page 41 Communication Devices Repair Documentation 3.4.1 Description of procedure: The connector X5 is connecting the main board of the C25 with the piezo ringer through a two pin cable. 3.4.1.1 Diagnosis Visually check the connector. Watch for bent contacts and dry joints.
  • Page 42 3.4.2.3 Special Tools None 3.4.2.4 Working materials Desolder Wick / Braid Solder Flux 3.4.3 Drawings Figure 1: C25 Board Ringer Connector Side Figure 2: C25 Ringer Connector (X5) Placement (Top View) V1.2 Page 10 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 43: Bottom Connector (Lumberg)

    Information and Communication Products Communication Devices 4 Bottom Connector (Lumberg) Affected Units 4.1.1 Type: 4.1.2 Affected IMEIs / Date Codes: All / All 4.1.3 Affected SW-Versions: 4.1.4 Fault Code for LSO reporting: 3LUC Fault Description 4.2.1 Fault Symptoms for customers: Charging problems.
  • Page 44 Resolder new bottom connector afterwards. 4.4.1.3 Repair by SW-Booting Not possible! 4.4.1.4 Test Retest handset after repair. 4.4.2 List of needed material 4.4.2.1 Components Bottom Connector C25 Part-Number: L36334-Z93-C262 4.4.2.2 Jigs and Tools Hot Air Blower Soldering Iron 4.4.2.3 Special Tools None V1.2...
  • Page 45 Information and Communication Products Communication Devices 4.4.2.4 Working materials Desolder Wick / Braid Solder 4.4.3 Drawings Figure 1: C25 Board Bottom Connector Side Figure 2: C25 Bottom Connector (X4) Placement (Top View) V1.2 Page 13 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 46: H Coil

    Information and Communication Products Communication Devices 5 18µH Coil Affected Units 5.1.1 Type: 5.1.2 Affected IMEIs / Date Codes: All / All 5.1.3 Affected SW-Versions: 5.1.4 Fault Code for LSO reporting: 3COI Fault Description 5.2.1 Fault Symptoms for customers: Loud humming noise in loudspeaker. 5.2.2 Fault Symptom on GSM-Tester: Handset fails with loud humming noise in echo loop.
  • Page 47 If the coil is mechanically damaged (broken) it produces heavy interference with the acoustical elements of the C25 resulting in a loud humming noise in the earpiece. A broken coil can easily be diagnosed by trying to move it with two fingers.
  • Page 48 Information and Communication Products Communication Devices 5.4.2 List of needed material 5.4.2.1 Components 18µH Coil Part-Number: L36151-F5183-M 5.4.2.2 Jigs and Tools Soldering Iron Hot Air Blower 5.4.2.3 Special Tools None 5.4.2.4 Working materials Desolder Wick / Braid Solder V1.2 Page 16 of 34 ICP CD ST D.
  • Page 49 Information and Communication Products Communication Devices 5.4.3 Drawings Figure 1: C25 Board 18µH Coil (L201) Side Figure 2: C25 18µH Coil (L1) Placement (Top View) V1.2 Page 17 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 50: Antenna Spring

    Information and Communication Products Communication Devices 6 Antenna Spring Affected Units 6.1.1 Type: 6.1.2 Affected IMEIs / Date Codes: All / All 6.1.3 Affected SW-Versions: 6.1.4 Fault Code for LSO reporting: 3ANS Fault Description 6.2.1 Fault Symptoms for customers: Network Search. Handset drops calls.
  • Page 51 Resolder new spring afterwards. 6.4.1.3 Repair by SW-Booting Not possible! 6.4.1.4 Test Retest handset after repair. 6.4.2 List of needed material 6.4.2.1 Components Antenna Spring C25 Part-Number: L36158-A25-C9 6.4.2.2 Jigs and Tools Hot Air Blower Soldering Iron V1.2 Page 19 of 34 ICP CD ST D.
  • Page 52 6.4.2.3 Special Tools None 6.4.2.4 Working materials Desolder Wick / Braid Solder 6.4.3 Drawings Figure 1: C25 Board Antenna Spring Side Figure 2: C25 Antenna Spring (X401) Placement (Top View) V1.2 Page 20 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 53: Display Connector

    Information and Communication Products Communication Devices 7 Display Connector Affected Units 7.1.1 Type: 7.1.2 Affected IMEIs / Date Codes: All / All 7.1.3 Affected SW-Versions: 7.1.4 Fault Code for LSO reporting: 3DIC Fault Description 7.2.1 Fault Symptoms for customers: Display problems. Missing Lines or columns on the LCD.
  • Page 54 Not possible! 7.4.1.4 Test Retest handset after repair. 7.4.2 List of needed material 7.4.2.1 Components Remark: Both C25 and C2588 use the same connector, but the placement position is slightly different! Display Connector C25(88) Part-Number: L36195-Z26-C624 7.4.2.2 Jigs and Tools...
  • Page 55 7.4.2.4 Working materials Desolder Wick / Braid Solder 7.4.3 Drawings Figure 1: C25 Board Display Connector Side Figure 2: C25 Display Connector (X3) and C2588 Display Connector (X2) Placement (Top View) V1.2 Page 23 of 34 ICP CD ST D. Schnoor...
  • Page 56 Information and Communication Products Communication Devices V1.2 Page 24 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 57: Display Capacitors

    Information and Communication Products Communication Devices 8 Display Capacitors Affected Units 8.1.1 Type: 8.1.2 Affected IMEIs / Date Codes: All / All 8.1.3 Affected SW-Versions: 8.1.4 Fault Code for LSO reporting: 3DCA Fault Description 8.2.1 Fault Symptoms for customers: The display is not working at all or shows strange characters.
  • Page 58 Resolder new capacitor afterwards. 8.4.1.3 Repair by SW-Booting Not possible! 8.4.1.4 Test Retest handset after repair. 8.4.2 List of needed material 8.4.2.1 Components Display Capacitor C25(88) Part-Number: L36375-F3224-K 8.4.2.2 Jigs and Tools Hot Air Blower Soldering Iron V1.2 Page 26 of 34 ICP CD ST D.
  • Page 59 None 8.4.2.4 Working materials Desolder Wick / Braid Solder 8.4.3 Drawings Figure 1: C25 Board Display Capacitor Side Figure 2: C25 Display Capacitor (C301, C302, C304, C307, C308) Placement V1.2 Page 27 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 60 Information and Communication Products Communication Devices C308 C304 C302 C307 C301 V1.2 Page 28 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 61: Ringer Coil

    Information and Communication Products Communication Devices 9 Ringer Coil Affected Units 9.1.1 Type: 9.1.2 Affected IMEIs / Date Codes: All / All 9.1.3 Affected SW-Versions: 9.1.4 Fault Code for LSO reporting: 3RCO Fault Description 9.2.1 Fault Symptoms for customers: The handset ringer (buzzer) is not working or the Ringer level is too low 9.2.2 Fault Symptom on GSM-Tester: Handset fails ringer test.
  • Page 62 Resolder new coil afterwards. 9.4.1.3 Repair by SW-Booting Not possible! 9.4.1.4 Test Retest handset after repair. 9.4.2 List of needed material 9.4.2.1 Components Ringer Coil C25(88) Part-Number: L36151-F5105-K3 9.4.2.2 Jigs and Tools Hot Air Blower Soldering Iron V1.2 Page 30 of 34 ICP CD ST D.
  • Page 63 9.4.2.3 Special Tools None 9.4.2.4 Working materials Desolder Wick / Braid Solder 9.4.3 Drawings Figure 1: C25 Board Ringer Coil Side Figure 2: C25 Ringer Coil (L300) Placement (Top View) V1.2 Page 31 of 34 ICP CD ST D. Schnoor 8/99...
  • Page 64: Keypad Leds

    Information and Communication Products Communication Devices 10 Keypad LEDs 10.1 Affected Units 10.1.1 Type: 10.1.2 Affected IMEIs / Date Codes: All / All 10.1.3 Affected SW-Versions: 10.1.4 Fault Code for LSO reporting: 3LED 10.2 Fault Description 10.2.1 Fault Symptoms for customers: The display/keypad illumination is not working properly.
  • Page 65 10.4.1.3 Repair by SW-Booting Not possible! 10.4.1.4 Test Retest handset after repair. 10.4.2 List of needed material 10.4.2.1 Components LED C25(88) Part-Number: L36840-L2031-D670 10.4.2.2 Jigs and Tools Hot Air Blower Soldering Iron V1.2 Page 33 of 34 ICP CD ST D.
  • Page 66 Information and Communication Products Communication Devices 10.4.2.3 Special Tools None 10.4.2.4 Working materials Desolder Wick / Braid Solder 10.4.3 Drawings Figure 1: C25 Board LED Side V1.2 Page 34 of 34 ICP CD ST D. Schnoor 8/99...

This manual is also suitable for:

C2588

Table of Contents