Installation Guide
Power over Ethernet

Advertising

   Related Manuals for HP J8726A

   Summary of Contents for HP J8726A

  • Page 1

    HP Switch zl Modules Installation Guide Power over Ethernet...

  • Page 3

    HP Switch zl Modules Installation Guide...

  • Page 4

    J8697A HP 20-port Gig-T PoE+ / 4-port SFP v2 zl Module J9535A E5406-48G zl Switch J8699A HP 20-port Gig-T PoE+ / 2-port 10-GbE SFP+ v2 zl Module J9536A HP E5406-44G-PoE+/4SFP zl Switch J9447A HP 24-port SFP v2 zl Module J9537A...

  • Page 5

    Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.

  • Page 7: Table Of Contents

    For the HP E5400 zl and E8200 zl Switches ......4 For the HP E8200 zl Switches Only ....... 9 E8200 zl Management Module Dependencies .

  • Page 8: Table Of Contents

    Contents Replacing or Removing a Module ........29 Troubleshooting .

  • Page 9: Hp Switch V2 Zl Modules

    Descriptions. The HP Switch v2 zl Modules are the second generation zl modules and provide a variety of improved network connectivity options for any of the HP E5400 zl or E8200 zl switches. The following modules are currently available. Compatibility Mode allows the inter-operation of v2 zl modules with the older zl modules in the same chassis switch.

  • Page 10

    HP Switch v2 zl Modules Module Description HP 20-port Gig-T PoE+ 20 twisted-pair ports with RJ-45 / 2-port 10-GbE SFP+ v2 connectors for 10/100/1000Base-T zl Module (J9536A) ports that support PoE+ and 2 ports for installing any of the supported HP transceivers.

  • Page 11

    This module requires switch software version K.15.04 or greater on both the E5400 zl chassis and E8200 zl chassis. Contact your HP authorized networking products reseller or your HP networking representative for information on availability of other modules. You can also visit the HP networking products Web site http://www.hp.com/networking...

  • Page 12: Hp Switch Zl Modules

    For the HP E5400 zl and E8200 zl Switches Descriptions. The HP Switch zl Modules are the first generation zl modules and provide a variety of network connectivity options for any of the HP E5400 zl or E8200 zl switches. The following modules are currently available.

  • Page 13

    STP cable. All ports have the IEEE 802.3ab Auto MDI/MDI-X (HP Auto-MDIX) feature and support IEEE 802.3at PoE+. HP Switch zl 4 port 10- 4 ports for installing any of the GbE X2 Module supported HP 10-GbE X2 1...

  • Page 14

    These modules require switch software version K.14.34 or greater and installed on the E5400 zl or E8200 zl chassis. Contact your HP authorized networking products reseller or your HP networking representative for information on availability of other modules and mini-GBICs. You can also visit the HP networking products Web site www.hp.com/ networking/support to get more information.

  • Page 15

    HP Switch zl Modules Module Description HP Redundant There are no ports on the J9052A. Wireless Services zl This module provides failover or Module (J9052A) high availability options for the J9051A module. There needs to be at least one J9051A in a chassis for the Note J9052A to operate.

  • Page 16

    Wireless Edge Services modules. For information on completing this configuration, see the Management and Configuration Guide on the HP Web site. For the latest version, visit the HP networking products Web site www.hp.com/networking/support.

  • Page 17: For The Hp E8200 Zl Switches Only

    E8200 zl Management Module Dependencies The HP E8206 zl and E8212 zl switches both use the same management module (J9092A). However, the E8206 zl switch Management Module requires soft- ware release K.14.34 or later, and the E8212 zl switch Management Module requires software release K.12.31 or later.

  • Page 18: E8206 Zl Module

    HP Switch zl Modules Note The management module must be updated in the E8212 zl switch prior to installing in the E8206 zl switch. This is because the E8206 zl switch does not recognize a management module running software prior to K.14.34.

  • Page 19: Steps To Update The E8212 Zl Module Software

    HP Switch zl Modules Steps to Update the E8212 zl Module Software Copy new software to primary or secondary flash memory on acitive management module: USB – E8200zl#copy usb flash K_13_60.swi pri TFTP – E8200zl#copy tftp flash 192.168.248.10 k_13_60.swi pri...

  • Page 20

    HP Switch zl Modules ProCurve J9093A,Fabric Module E8200zl Enabled ProCurve J9093A,Fabric Module E8200zl Enabled Example when standby management the module has rebooted. ProCurve Switch E8212zl# show redundancy Settings -------- Mgmt Redundancy : Enabled Statistics ---------- Failovers Last Failover : Tue May 12 17:30:07 2009...

  • Page 21: Network Interface Module Leds

    Network Interface Module LEDs Network Interface Module LEDs Network Connectivity Modules Port LEDs There are two LEDs for each port: ■ The Link LED lights green with a valid connection and orange if there is a fault or alert condition. ■...

  • Page 22: Wireless Edge Module Leds

    Network Interface Module LEDs Wireless Edge Module LEDs There are no network connectivity ports on the J9051A or J9052A. The module enables the Switch to operate with ProCurve Radio Ports as a centrally-administered Wireless LAN system. LEDs State Meaning Module Ready The normal state;...

  • Page 23: Features

    Module Features Link and Mode LEDs (one pair per port) retaining screw network ports Figure 2. Example: HP 24-port Gig-T PoE+ v2 zl Module Link and Mode LEDs SFP+ ports (one pair per port) Extractor handles Figure 3. Example: HP 8-port 10-GbE SFP+ v2 zl Module...

  • Page 24: Zl Module Features

    (one pair per port) network ports Figure 4. Example: HP ProCurve 24-Port 10/100/1000-T zl Module Link and Mode LEDs (one pair per port) port covers Extractor handles Figure 5. Example: HP ProCurve Switch 4-port 10 Gig-X2 zl Module...

  • Page 25: The Zl Modules Have The Following Features

    • the RJ-45 ports on all modules have the HP Auto-MDIX and the IEEE 802.3ab Auto MDI/MDI-X feature. These features operate the same way and allow you to use either straight-through or crossover twisted- pair cables for all the twisted-pair network connections.

  • Page 26: Installing The Modules

    6 software version, and see for the previous module software versions. You can install any of the modules into any of the HP networking chassis zl switches that have compatible module slots. HP E5400 zl Switches: E5406 zl and all related bundles ■...

  • Page 27: Installing The Module In An Unused Slot

    The HP Switch zl Modules have “low-force”, high-performance connectors. High insertion ■ forces are not necessary to install the modules, and should not be used.

  • Page 28

    Installing the Modules Insert module into the guides and slide it in until it is fully inserted. Open extractor handles Figure 6. Example: Module being installed Use the extractor handles to seat the module completely. Then tighten the retaining screws on the module until they are secure, but do not overtighten them.

  • Page 29: Installing Or Removing A Mini-gbic Or Sfp Transceiver

    Installing the Modules Installing or Removing a mini-GBIC or SFP transceiver You can install or remove a mini-GBIC or SFP transceiver from the mini-GBIC zl Module without having to power off the switch. Use only HP mini-GBICs or SFP transceivers. WARNING The HP mini-GBICs and SFPs are Class 1 laser devices.

  • Page 30: Install Or Remove An X2 Transceiver

    Installing the Modules Install or Remove an X2 Transceiver Note Hot swapping transceivers is supported. You can install or remove a trans- ceiver with the switch powered on, a reset will not occur. a. Slide the transceiver in until it stops. b.

  • Page 31: Verifying The Module Is Installed Correctly

    Installing the Modules Verifying the Module is Installed Correctly Observe the Module Status LED for the slot in which the module is being installed, and the Test and Fault LEDs on the switch to verify the module is installed properly. Test LED Module Status LEDs Fault LED...

  • Page 32

    Installing the Modules LED Behavior Display for a Properly Installed Module Module Status (for the slot in which you are installing the module) The LED goes ON as soon as the module is installed and the switch is powered on, and stays ON steadily.

  • Page 33: Connecting The Network Cables

    Installing the Modules Connecting the Network Cables Connect the appropriate network cables to the module's ports as shown in the table below. For more information on the cable specifications, see page “Cabling and Technology Specifications” on Module 10/100/1000-T PoE zl Module twisted-pair cable with RJ-45 ports with...

  • Page 34: Connecting A Fiber Cable To An X2 Transceiver

    Installing the Modules Connecting a fiber cable to an X2 transceiver To connect: 1. Remove the dust covers from the cable connectors and the port.   2. Aligning the notches on the cable connectors with the slots of the port, press the cable connector into the port until it...

  • Page 35: Verifying The Network Connections Are Working

    Installing the Modules Verifying the Network Connections Are Working Check the port LEDs for the newly-installed module to ensure the port(s) connected in the preceding step are operating correctly. Each port on the switch modules has Link and Mode LEDs near it as shown in the next illustration.

  • Page 36: Default Port Configuration

    By default, all ports on the J8702A and J8705A modules have PoE power enabled. Ports on the J9307A and J9308A modules provide PoE+ power. For information regarding customizing PoE and PoE+ ports refer to the HP Power over Ethernet (PoE/PoE+) Planning and Implementation Guide that is on...

  • Page 37: Replacing Or Removing A Module

    Replacing or Removing a Module Replacing or Removing a Module Follow these procedures to replace one module with another, or to remove a module without replacing it: Remove any network cables from the ports on the module. If the module you want to remove has a shutdown button, make sure to shut down the module before removing it either by using the CLI ...

  • Page 38: Troubleshooting

    See the Customer Support/Warranty booklet located on the HP networking products Web site, www.hp.com/networking/ support. Additionally, your HP-authorized network reseller can also provide you with assistance, both with services they offer and with services offered by HP.

  • Page 39: Before Calling Support

    Customer Support Services Before Calling Support Before calling your networking dealer or HP Support, to make the support process most efficient, retrieve the following information: Information Item Information Location • product identification, including the chassis, the front of the switch, and on the...

  • Page 40: Specifications

    0C to 40C (32F to 104F) -40C to 70C (-40F to 158F) J8708A 0C to 55C (32F to 131F) -40C to 70C (-40F to 158F) J8726A 0C to 55C (32F to 131F) -40C to 70C (-40F to 158F) J9051A 0C to 40C (32F to 104F) -40C to 70C (-40F to 158F)

  • Page 41: Network Connectivity Speeds And Technologies

    10-Gig ER Fiber (single mode) For supported transceivers, visit www.hp.com/networking/support – In the first textbox, type J4858 (for 100-Mb and Gigabit information), or J8436 (for 10-Gigabit information). – Select any of the products that display in the dropdown list. – Select Product support information. Then click on Manuals and find the Transceiver Support Matrix.

  • Page 42: Technology Standards And Safety Compliance

    Specifications Technology Standards and Safety Compliance Table 2. Technology Standards and Safety Compliance Laser safety information Technology Compatible EN/IEC SFP+ Media with these IEEE standard ("mini-GBIC") Lasers Lasers Converter standards compliance Lasers Lasers 10-T IEEE 802.3  10BASE-T 100-TX IEEE 802.3u 100BASE-TX 1000-T...

  • Page 43

    Specifications Table 2. Technology Standards and Safety Compliance (Continued) Laser safety information Technology Compatible EN/IEC SFP+ Media with these IEEE standard ("mini-GBIC") Lasers Lasers Converter standards compliance Lasers Lasers 10-Gig SR IEEE 802.3ae EN/IEC 60825 Class 1M Class 1 Laser 10GBASE-SR Laser Product...

  • Page 44: Cabling And Technology Specifications

    Specifications Cabling and Technology Specifications Table 3. Cabling Specifications 10 Mbps Operation Category 3, 4 or 5, 100-ohm unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable, complying with IEEE 802.3 10BASE-T specifications. 100 Mbps Operation Category 5, 100-ohm UTP or STP cable, complying with IEEE 802.3u 100BASE-TX specifications.

  • Page 45

    For 10GBASE-T, Category 6 patch cables are sensitive to movement once link has been established, and could cause link to drop if moved. Therefore HP recommends using Category 6A patch cables, or using cable management options to tie down (dress) the Category...

  • Page 46: Technology Distance Specifications

    Specifications Technology Distance Specifications Table 4. Technology Distance Specifications Technology Supported cable type Multimode fiber Supported distances modal bandwidth 100-FX multimode fiber up to 2,000 meters 100-BX single mode fiber 0.5 - 10,000 meters 1000-T twisted-pair copper up to 100 meters ...

  • Page 47: Mode Conditioning Patch Cord

    Specifications Table 4. Technology Distance Specifications(Continued) Technology Supported cable type Multimode fiber Supported distances modal bandwidth 10-Gig ER single mode fiber 2 - 40,000 meters CX4 Media Converter 12-strand female-female multi- 150 MHz*km 1 - 50 meters mode fiber MPO ribbon cable 500 MHz*km...

  • Page 48: Installing The Patch Cord

    Specifications Note Most of the time, if you are using good quality graded-index multimode fiber page 36, there should not be a cable that adheres to the standards listed on need to use mode conditioning patch cords in your network. This is especially true if the fiber runs in your network are relatively short.

  • Page 49: Emc Regulatory Statements

    EMC Regulatory Statements EMC Regulatory Statements U.S.A. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment.

  • Page 50: Korea

    Korea Taiwan European Community Declaration of Conformity These products are designed for operation with the HP switches that have zl module slots. Please see the Declarations of Conformity included in the Installation Guides for those products. N o t e...

  • Page 51: Waste Electrical And Electronic Equipment (weee) Statements

    Waste Electrical and Electronic Equipment (WEEE) Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.

  • Page 52

    Waste Electrical and Electronic Equipment (WEEE) Statements Élimination des appareils mis au rebut par les ménages dans l'Union européenne Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques et électroniques.

  • Page 53

    Para obter mais informações sobre locais que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço de coleta de lixo ou com a loja em que o produto foi adquirido.

  • Page 54

    Waste Electrical and Electronic Equipment (WEEE) Statements Likvidácia vyradených zariadení v domácnostiach v Európskej únii Symbol na výrobku alebo jeho balení označuje, že daný výrobok sa nesmie likvidovať s domovým odpadom. Povinnosťou spotrebiteľa je odovzdať vyradené zariadenie v zbernom mieste, ktoré je určené...

  • Page 56

    © Copyright 2005-201 1 Hewlett-Packard Development Company, L.P. The information Copyright Hewlett-Packard Company,  contained herein is subject to change without notice. The only warranties for HP products 2005 -2011. All rights reserved. and services are set forth in the express warranty statements accompanying such products and services.

Comments to this Manuals

Symbols: 0
Latest comments: