Cleaner Maintenance - Hoover vacuum cleaner User Manual

3 in 1 tool – Combines several functions in one. The 3 in 1 tool can be stored neatly
underneath the hose handle. [1]
dusting brush – For bookshelves, frames, keyboards and other delicate areas. To extend
the brushes push the button on the body of the tool. [22]
Crevice Tool – For corners and hard to reach areas. [23]
Furniture Nozzle – For soft furniture and fabrics [24]
Parquet Caresse Nozzle* – For parquet floors and other delicate floors. [1U]
Pet Hair Remover mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for
deepcleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [1V]
Allergen Remover mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deepcleaning
on textile surfaces and other hard to clean areas. Particularly suitable for allergen removal. [1w]
Grand Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1X]
Stair Cleaning Stretch Hose* – Use for stair cleaning and areas requiring long reach.[1y]
Use this in addition to the standard cleaner hose. Attach the hose to the end of the hose
handle. [25]
ImPORTANT: Do not use the grand turbo and mini turbo nozzles on rugs with long fringes,
animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while
the brush is rotating.

ClEANER mAINTENANCE

Emptying the dust Container
When the dust reaches the max level indicator in the container empty the dust bin.
ImPORTANT:To maintain optimum performance do not allow the dust to sit higher than the
max level.
1. Release the container by sliding the dust container release button towards the rear of
the cleaner. [13] Lift the dust container from the cleaner main body.
2. Hold the dust container over a bin with one hand and press the bin container door open
trigger. [14]
3. Close the dust container door and refit to the cleaner main body.
Cleaning the washable filters
The cleaner is fitted with a blue filter pack. To maintain optimum cleaning performance
regularly remove the the filters and tap against the side of the bin to release dust. The filters
should be washed every 3 months or when the filter has excessive dust level.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean your
filters may result in air blockage, overheating and product failure. This may invalidate
your guarantee.
*Certain Models Only ** Certain models only, nozzles may vary according to model
ImPORTANT: Always ensure the filters are fully dry before use.
To access the pre-motor filter:
1. Release the container by sliding the dust container release button towards the rear of
the cleaner. [13] Lift the dust container from the cleaner main body.
2. Hold the dust container with one hand and with the other hand rotate the bin handle
anti clockwise to release it from the dust container. [15]
3. Remove the blue filter pack located in the dust container handle. [16]
4. Remove the foam filter from the filter pack. [17]
5. Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using. [18]
6. Reassemble to filter pack once fully dry and refit to the cleaner.
ImPORTANT: Do not use the product without the filter pack fitted.
To access the exhaust filter:
1. Unclip the exhaust filter from the rear of the cleaner. [19]
2. Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using.
Cleaning the dust container / multi-cyclonic separation unit
This cleaner uses a multicyclonic separation system, unique to Hoover. If necessary the
separation unit can be disassembled from the dust container and cleaned.
1. Release the dust container by sliding the dust container release button towards the
rear of the cleaner. [13] Lift the dust container from the cleaner main body.
2. Hold the dust container with one hand and with the other hand rotate the dust container
handle anti clockwise to release it from the dust container. [15]
3. Remove the multicyclonic separation unit from the dust container by pulling the handle
provided.[20]
4. If necessary, use a cloth to remove excessive dust from the multi-cyclonic unit surface. [21]
5. Reassemble the multicyclonic separation unit to the dust container and refit the filter
pack in position.
6. Reassemble the dust container handle to the bin container. Refit the dust container to
the cleaner.
NOTE: For stubborn dirt the multi-cyclonic separation unit, or the dust container can be
washed, but care must be taken to ensure that both are completely dry before use.
ImPORTANT: For optimum performance, we recommend that the multi-cyclonic separation
system is inspected after each empty.
Removing a blockage from the cleaner
1. Check if the dust container is full. If so refer to 'Emptying the dust container.
3