Omni combined bar code and magnetic stripe reader (34 pages)
Summary of Contents for ID Tech EconoScan
Page 1
ID Tech EconoScan Manual More information available at POSMicro.com QUESTIONS? BULk DISCOUNTS SE HaBLa Ask the experts at POSMicro.com. ESpañOL FREE SHIPPING* 1.800.241.6264 Live Chat Now support@POSMicro.com Monday - Friday 6 AM to 5 PM Pacific Time *Free ground shipping to the continental USa on orders over $100.
Page 2
EZ One Shot BAR CODE SCANNER PROGRAMING SETUP MANUAL Default Default DEFAULT CHECK VERSION MANUAL VER: MAR20020808...
Page 3
WARNING Please shut down the Power of your P/C system before connecting the scanner. This process is critical prior protecting both scanner and your P/C system from serious damage We reserve the right to change the specifications and other info without prior notice, please contact us for the updated info.
CONTENTS GENERAL TABLE OF CONTENTS ----------------------------------------------------------------------- 1 INTRODUCTION, EZ TROUBLESHOOTING ----------------------- --- ----------- 2~3 CLONING MODE ----------------------------------------------------------------------------4~5 GETTING STARTED >>> HOW TO FIX THE SCANNER TO THE TERMINAL -----------------------6~7 >>> HOW TO CHANGE A CABLE -------------------------------------------------------- 7 >>> HOW TO SETUP THE PARAMETER.---------------------------------------------- 8 SETTING GROUP GROUP 1 >>>>...
INTRODUCTION Machine-readable bar codes save human from senseless boredom and costly errors of data entry. Human use a keyboard or a mouse for data entry to a computer. Bar codes must be scanned in via some other means. Thus bar code Scanner is a high performance input devices which provide fast and accuracy for bar code encoding, and will improve your work efficiency.
CLONING MODE WHAT IS CLONING MODE? CLONING means duplicate a parameter's setup of a scanner to the other's scanners. It can save much time for lots scanner setting. HOW SHOULD THE CLONING WORK? Step 1 : Take a scanner, set all the parameters with this manual. Step 2 : Scan the CLONING MODE bar code shown at Figure 1.
Page 8
EXAMPLE : 1. Project Assignments : 1.1. Beep tone: BEEP LOW -- HIGH . 1.2. Capslock Mode: CAPSLOCK ON ( FIXED ). 1.3. Reading Mode: CONTINUOUS AUTO OFF. 2. Setting Procedure: 2.1. Scan BEEP LOW.--HIGH (GROUP 3). 2.2. Scan CAPSLOCK ON (FIXED).(GROUP 3). 2.3.
GETTING STARTED HOW TO FIX THE SCANNER TO TERMINAL KEYBOARD WEDGE 1. Turn off the power of a terminal / computer / notebook.. 2. Disconnected the cable from the terminal / computer 3. Connect an appropriate keyboard cable to the scanner and to the terminal. 4.
USB Interface The USB Interfaces supported is compatible to Apple MAC series / later PCs and Window 98, Window 2000, Window Me, Window XP. 1. Turn off power to the terminal / computer 2. Disconnected the cable the terminal/ computer. 3.
HOW TO SETUP THE PARAMETER EZ One Shot Setting Procedure. How do you program a scanner with this manual? 1. Aim the scanner directly to the bar code ( function/ parameter ) you want to set, 1.1. Then you will hear TWO beep sounds, mean the NEW parameter is defined or updated into the memory processor.
-- GROUP 1 -- INTERFACES SELECTION, COMPUTER TYPE, DEFAULT. . A001$ DEFAULT . C004$ COMPUTER TYPE . C005$ PC- AT . C006$ PC-XT . C007$ MAC ADB NOTEBOOK* SYMPTOMS SOLUTION Scanners perform well as usual, but 1.Unplugged the cable from there is no any output show on the the computer, Computer's monitor while the...
-- GROUP 2 -- READING MODE SETTING . F005$ * LED is always on. , * The trigger is functionless eternally if Continuous Mode on. CONTINUOUS MODE . F001$ * LED is always on if bar codes close to the scanner, and turns to flashing when there is no any bar code approaching after 60 sec.
-- GROUP 5 -- ACCURACY ADJUSTMENT . A010$ ACCURACY ADJUSTMENT Accuracy Adjustment aims to assure for getting more reliable decoded output. The accurate decoded output can be adjusted by customer as follow. The higher the numbers is set mean more accurate output will be. The higher the number is set, SETTING PROCEDURE STEP 1 : Scan : ACCURACY ADJUSTMENT.
-- GROUP 6 -- ENABLE AND DIABLE CODE ID ENABLE CODE ID . A008$ FACTORY ID ON . A014$ AIM ID ON . A015$ SET ID -ON . A009$ DISABLE CODE ID REMARK: 1.Among those Code ID, only ONE type code ID will be sent. 2.Code ID is located at the position before the bar code data and after the preamble, The Structures of data will be show as follow:...
-- GROUP 7 -- SYMBOLOGIES CODE ID IDENTIFIER, SET ID SYMBOLOGIES CODE ID IDENTIFIER Factory SYMBOLOGIES SYMBOLOGIES Factory ID CODABAR EAN 8 DELTA Code UPC-E LABEL Code UPC-A UK PLESSY EAN 13 MATRIX 2 OF 5 Code 93 ]G0 FULL ASCII Code 39 Code 11 ]H0 STANDARD Code 39 TELEPEN...
-- GROUP 8 -- CODE ID CONFIGURATION: SET ID . P001$ EAN 13 Set ID . P002$ EAN 8- Set ID . P003$ UPC E Set ID . P004$ UPC A Set ID . P005$ CODE 39 Set ID . P013$ Code 93 Set ID .
Page 20
-- GROUP 9 -- CODE ID CONFIGURATION: SET ID . P012$ China Post Code [ TOSHIBA Code ] Set ID . P014$ MSI Code Set ID . P015$ UK Plessy Set ID . P017$ Matrix 2 of 5 Set ID .
APPENDIX 1 FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH (Default Length) STEP 1 - Scan: MIN / MAX LENGTH STEP 2 - Scan : " TWO DIGIT " Number from Appendix 1. STEP 3 - Scan: MIN / MAX LENGTH. Be noticed that the scanner will only read a bar code within the length's limit.
APPENDIX 1 FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH (Default Length) STEP 1 - Scan: MIN / MAX LENGTH STEP 2 - Scan : " TWO DIGIT " Number from Appendix 1. STEP 3 - Scan: MIN / MAX LENGTH. Be noticed that the scanner will only read a bar code within the length's limit.
APPENDIX 1 FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH (Default Length) STEP 1 - Scan: MIN / MAX LENGTH STEP 2 - Scan : " TWO DIGIT " Number from Appendix 1. STEP 3 - Scan: MIN / MAX LENGTH. Be noticed that the scanner will only read a bar code within the length's limit.
APPENDIX 1 FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH (Default Length) STEP 1 - Scan: MIN / MAX LENGTH STEP 2 - Scan : " TWO DIGIT " Number from Appendix 1. STEP 3 - Scan: MIN / MAX LENGTH. Be noticed that the scanner will only read a bar code within the length's limit.
-- GROUP 21 -- SYMBOLOGIES FORMATTING: CODABAR . I 001$ CODABAR . I 007$ ENABLE . I 002$ CDV & NOT SEND CD . I 008$ DISABLE . I 005$ MIN LENGTH ( 6 ) . I 009$ DISABLE CDV .
APPENDIX 1 FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH (Default Length) STEP 1 - Scan: MIN / MAX LENGTH STEP 2 - Scan : " TWO DIGIT " Number from Appendix 1. STEP 3 - Scan: MIN / MAX LENGTH. Be noticed that the scanner will only read a bar code within the length's limit.
-- GROUP 22 -- SYMBOLOGIES FORMATTING: ABC-CODABAR, CX- CODABAR . I 017$ ABC- CODABAR . I 039$ . I 018$ INSERT DATA -ON . I 036$ . I 035$ INSERT DATA- OFF SET INSERT DATA* *The data can be any alphanumerics of FULL ASCII Table ( GROUP 32- 40 ) REMARK: ABC-CODABAR (American Blood Commission.).The ABC Code is an acronym for American Blood Commission.
-- GROUP 23-- SYMBOLOGIES FORMATING: CODABAR COUPLING, ADJACENT MUST ON . . I 019$ CODABAR COUPLIN . I 041$ . I 020$ INSERT DATA -ON . I 026$ . I 021$ INSERT DATA- OFF SET INSERT DATA* ABC-CODABAR and CX-CODABAR code have certain rules of Stop Character of first bar code and the stop character of Second bar code while conjunction, but CODABAR COUPLING does not have any limitation of that, means that while CODABAR COUPLING...
APPENDIX 1 FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH (Default Length) STEP 1 - Scan: MIN / MAX LENGTH STEP 2 - Scan : " TWO DIGIT " Number from Appendix 1. STEP 3 - Scan: MIN / MAX LENGTH. Be noticed that the scanner will only read a bar code within the length's limit.
APPENDIX 1 FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH (Default Length) STEP 1 - Scan: MIN / MAX LENGTH STEP 2 - Scan : " TWO DIGIT " Number from Appendix 1. STEP 3 - Scan: MIN / MAX LENGTH. Be noticed that the scanner will only read a bar code within the length's limit.
-- GROUP 31 - - SYMBOLOGIES FORMATTING: EAN/UCC-128 . M001$ EAN/ UCC- 128 . M005$ ENABLE . M002$ FUNC 1CHEAR SEND . M006$ DISABLE . M003$ FUNC 1 CHEAR NOT SEND . M007$ CODE ID ENABLE . M004$ DEFINE EAN 128 CODE ID DISABLE REMARK :DEFINE EAN 128 The first FNC1 character is translated to ]c1, and the second FNC1...
-- GROUP 41 - - FUNCTION CODE ( CODE 39 ) FOR PC AT $T A $T B $T C $T D $T E $T F $T G $T H $T I $T J $T K $T L $T M Home $T N...
Page 59
-- GROUP 42 -- FUNCTION CODE ( CODE 39 ) FOR PC AT $T O $T P Right Left $T Q $T R Down $T S Page Up $T T $T U Page Down $T V Back Tab $T W $T X Enter $T Y...
-- GROUP 43 -- TROUBLE SHOOTING The Decoder CCD scanner is a simple device to install and use. Therefore, most of the problems can be attribute to these areas: The troubleshooting process may follow simple procedures as below: INCORRECT CONFIGURATION SETUP INCORRECT INTERFACES CONNECTION POOR BAR CODE SYMBOL QUALITY.
Page 61
-- GROUP 44 -- TROUBLE SHOOTING Does the keyboard work. Since the key- in data from keyboard must pass through the decoder, the cabling connections are correct if the keyboard is functioning well. Can your computer accept the data fast enough? Computer's BIOS has a feature related to keyboard typing speed.
Page 62
-- GROUP 45 -- TROUBLE SHOOTING CONFIGURATION SETUP Are you setup to the Right Interfaces 1.Interface setting does not match with the right interface. For instance you select keyboard cable, but you had set it to Rs232 or Wand Emulation. 2.
Page 63
-- GROUP 46 -- TROUBLE SHOOTING POOR BAR CODE QUALITY The third problem area has nothing to do with the unit, but rather the quality of the bar code and / or the scanning technique. TOLERANCE OF BAR CODE B ar codes may have a tolerance. Normally the tolerances are caused by Bar code software or of printer, a reputation high quality bar code software should be choose to generate bar codes.