CONTENTS PREFACE Table of Contents............LED & Beeper Indication..........Cloning Mode............How to fix the scanner to the terminal....... How to change a cable..........How to set up the parameter........GENERAL SETTINGS (GROUP 1 - 12) Default, Abort, Check Version, Setup Code Read..Reading Mode ............
Page 3
CONTENTS SYMBOLOGIES (GROUP 34 - 51) 34~36 Enable/Disable Barcode Symbology..43-45 China postcode(Toshiba code)....... 37 MSI code, UK Plessey code........47 Code 93, Telepen, IATA.......... Interleaved 2 of 5, Code 11........51 Industrial 2 of 5, Matrix 2 of 5......... 41 Codabar..............55 ABC Codabar, CX Codabar........
LED & BEEPER INDICATION Status Blue/Green LED Red LED Beeper Remark Initializing/ Solid for 2 sec 1 long beep Power-up Successful Barcode 1 Flash 1 beep Scan Successful 2 Flashes 2 beeps Connection Reads 2 beeps Configuration Barcode Data See Batch Mode Temporarily/ 2 short beeps 1 Flash...
CLONING MODE WHAT IS CLONING MODE? CLONING duplicates a scanners settings in other scanners. It can save time when a number of scanners must be programmed to the same settings. HOW SHOULD CLONING WORK? 1. Using this guide, make all the necessary settings for one wand. 2.
HOW TO CONNECT THE SCANNER TO THE HOST TERMINAL: Handheld Barcode Scanner KEYBOARD WEDGE INTERFACE 1. Power down the host computer. 2. Disconnect the keyboard cable from the computer. 3. Connect the “Y ” cable between the keyboard and the scanner and computer. 4.
USB INTERFACE The USB Interface supported is compatible with Apple MAC series, , Windows 98, 2000, XP, Vista, 7, 8 and so on. 1. Connect the USB cable between the scanner and the computer. 2. The scanner will beep. 3. The scanner will detect the USB driver automatically. (The first time the scanner is connected via the USB port, follow the appropriate instructions for the host computer.) 4.
HOW TO SET PARAMETERS How do you program a scanner with this user’s guide? 1. Use the scanner to scan at the bar code representing the function/ parameter you want to set. 2. When you hear two beeps, the new settings have been defined or updated into the memory processor.
GROUP-1 GENERAL SETTINGS . A001$ DEFAULT *Reset to factory default . A007$ CHECK VERSION *Check firmware version . P023$ RESET/ ABORT *Abort multi-step configuration SETUP CODE ON SETUP CODE READ SETUP CODE OFF *Caution: Scanning SETUP CODE OFF will turn the scanner into unprogrammable state and the scanner will not react to any configuration barcode!
GROUP-2 GENERAL SETTINGS - READING MODE . F005$ LED is always on. The trigger does not function in Continuous Mode. CONTINUOUS MODE . F001$ The LED is on steady if a bar code is close to the scanner, but starts flashing if no bar code is detected after 60 FLASH MODE seconds.
GROUP-5 GENERAL SETTINGS - ACCURACY ADJUSTMENT . A010$ ACCURACY ADJUSTMENT Accuracy Adjustment assures a more reliable decoded output. Enabling the feature and setting a number from 1 to 9 subjects the decoded output a higher standard of accuracy. The higher the number, the greater the accuracy.
GROUP-6 GENERAL SETTINGS ENABLE INVERSE BARCODE .D021$ DISABLE INVERSE BARCODE [READS POSITIVE BARCODE ONLY] .D022$ ENABLE INVERSE BARCODE [READS POSITIVE & NEGATIVE BARCODES] ENABLE CODE ID .A008$ FACTORY ID ON .A014$ AIM ID ON .A015$ SET ID ON DISABLE CODE ID .A009$ NOTES: 1.
GROUP-8 GENERAL SETTINGS - SET CODE ID . P001$ EAN 13 Set ID . P002$ EAN 8 Set ID . P003$ UPC E Set ID . P004$ UPC A Set ID . P005$ Code 39 Set ID . P013$ Code 93 Set ID .
Page 18
GROUP-9 GENERAL SETTINGS - SET CODE ID . P014$ MSI Code Set ID . P015$ UK Plessey Set ID . P017$ Matrix 2 of 5 Set ID . P006$ Interleaved 2 of 5 Set ID . P018$ Industrial 2 of 5 Set ID .
GROUP-11 GENERAL SETTINGS KEYBOARD LAYOUT . C009$ . C010$ JAPAN (106 key) . C025$ ENGLISH (USA) . C018$ CANADIAN (FRENCH) . C034$ ENGLISH (UK) . C012$ CANADIAN (TRADITIONAL) . C029$ FRENCH . C011$ NORWEGIAN . C026$ GERMAN . C014$ SWEDISH .
GROUP-12 GENERAL SETTINGS . A005$ CAPITAL LOCK MODE CAPLOCK OFF . A004$ . A006$ CAPLOCK ON CAPLOCK FREE NOTE: 1. When barcode scanner is set to Caplock Free mode, no matter keyboard Capslock LED indicator is ON or OFF, output will be always the same as the Original barcode.
GROUP-13 TETHERED SCANNER SETTINGS . C004$ PC-AT COMPUTER TYPE . C007$ NOTEBOOK* SYMPTOMS SOLUTION Scanner seems to be 1. Unplug the cable from the host computer. performing as usual, 2. Plug the cable back into the host computer. but no data is being 3.
GROUP-14 TETHERED SCANNER SETTINGS (The following are only supported by Bi-Color models) BI-COLOR: CYCLE MODE . D027$ *.D027$* GREEN > RED . D028$ *.D028$* RED > GREEN . D029$ *.D029$* GREEN > BI-COLOR . D030$ *.D030$* RED > BI-COLOR 1. Illumination color will switch back and forth from one to another when good read does not occur.
GROUP-15 ADVANCED AUTO-SENSING SETTINGS (The following is only supported by autosensing models) MAGNETIC SWITCH . F034$ (CCD & LASER SCANNERS) MAGNETIC SWITCH ON . F035$ MAGNETIC SWITCH OFF NOTES: 1. The Magnetic Switch is automatically activated when Auto- Sensing Mode is on. 2.
GROUP-16 ADVANCED AUTO-SENSING SETTINGS (The following is only supported by autosensing models) DEACTIVATION TIME . F030$ (CCD & LASER SCANNERS) DEACTIVATION TIME NOTES: 1. The default of Deactivation Time is 3 Sec. 2. Deactivation Time is the time interval between the last scan and the automatic deactivation of LED or Laser light in Auto-Sensing Mode.
GROUP-19 TETHERED SCANNER - WAND EMULATION SETTINGS . D001$ LEVEL DURATION OF MINI WIDTH 200us . D002$ 600uS . D003$ POLARITY OF IDLE CONDITION . D004$ HIGH . D005$ OUTPUT OF WAND EMULATION Bar High / Space Low . D006$ Bar Low / Space High .
GROUP-20 WIRELESS SCANNER SETTINGS INTERFACE . E043$ *.E043$* BT HID Emulates a Bluetooth HID keyboard that transmits each barcode data to the host after decode. . E042$ *.E042$* BT SPP Emulates a Bluetooth SPP device that transmits each barcode data in serial communication to the host after decode.
GROUP-21 WIRELESS SCANNER SETTINGS BLUETOOTH PROFILE . E043$ (Recommanded) BT mode - HID 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT mode - HID]; the scanner will emit several beeps. 4. Select “Wireless Scanner” from discovered device list. (For PC, please click “Create a pairing code for me”) 5.
GROUP-23 WIRELESS SCANNER SETTINGS Getting Connected - iOS (Apple) (Group 21), Simply follow instruction in [BT mode - HID]. in which step 5 & 6 can be skipped since Apple devices will not require pincode for connection. Touch Keyboard . E047$ ENABLE iOS HOTKEY .
GROUP-24 WIRELESS SCANNER SETTINGS POWER OFF TIMEOUT Variable Timeout . B030$ *.B030$* SET MINUTE (Range: 00 ~ 60) . B029$ *.B029$* SET SECOND (Range: 00 ~ 60) The timeout is 3 minutes by default, and is programmable to the second and minute, ranging from 10 seconds (00:10) to 60 minutes and 60 seconds (60:60) For example, to set the timeout as 5 minutes 30 seconds: 1.
GROUP-25 WIRELESS SCANNER SETTINGS SET BLUETOOTH DEVICE ID To customize your own Bluetooth device name for the wireless scanner, please follow below steps: STEP 1 . B022$ Default Wireless ID STEP 2 . B023$ Set Wireless ID STEP 3 Scan up to 16 alphanumeric characters from Full ASCII Table (GROUP 52-60) as your desired ID name.
GROUP-26 WIRELESS SCANNER SETTINGS SET SPP PINCODE By default, the pincode under SPP profile for the scanner is “1234”. You may customize this pincode with below steps: STEP 1 . B024$ Set SPP Pincode STEP 2 (see below) Scan numeric barcodes NUMERIC BARCODES Up to 8 numbers can be set as SPP pincode.
GROUP-27 WIRELESS SCANNER SETTINGS SPP MASTER MODE First, please generate one configuration barcode for the target SPP slave device in below methods: 1. The barcode must be Code 39 with no checksum 2. Barcode data format: LTB + Target MAC address For example, the target SPP slave device’s MAC address is 001583522C3B.
GROUP-28 WIRELESS SCANNER SETTINGS SPP REMOTE CONTROL There are two ways to verify connection status by the host under SPP profile. Command Response Host sends: CR,LF,{,A,L,},CR,LF (8 bytes) Scanner replys: O,K,CR,LF (4 bytes) Beeper Response Host sends: CR,LF,{,M,1,},CR,LF (8 bytes) Scanner reacts: a short beep SHUT DOWN...
GROUP-29 WIRELESS SCANNER SETTINGS BATCH MODE . E054$ ENABLE . E053$ DISABLE When out of range, the scanner will temporarily keep scanned data in its memory buffer(2K RAM) until the buffer is full. When back in range, the scanner will send all stored data back to the host. *Note: 1.
GROUP-30 WIRELESS SCANNER SETTINGS MEMORY MODE For memory version only . C035$ *.c035$* MEMORY MODE After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: <...
GROUP-31 WIRELESS SCANNER SETTINGS DATA FORMAT For memory version only . R011$ *.R011$* DATA FORMAT The default Data Format is <Date>, <Time>, <Barcode Data> below are items and their setup codes: Code Item Code Item Date Barcode Data Time Quantity Example: To change Data Format to <Barcode Data>, <Date>, <Time>...
GROUP-32 WIRELESS SCANNER SETTINGS DATE FORMAT For memory version only . R008$ *.R008$* DATE FORMAT The default Date Format is DD/MM/YYYY (Code = 09), below is full list of available formats and their setup codes: Code Format Code Format DD-MM-YYYY DD/MM/YYYY MM-DD-YYYY MM/DD/YYYY...
GROUP-33 WIRELESS SCANNER SETTINGS QUANTITY For memory version only . R017$ *.R017$* ENABLE QUANTITY INPUT Once you enable quantity input, the operation procedure under memory mode will be as follows: 1. Scan [MEMORY MODE] (Group 30) 2. Set DATA FORMAT (Group 31) as appropriate. For example, your data format is <Barcode Data>, <Quantity>.
Page 46
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters.
GROUP-37 SYMBOLOGIES: MSI CODE, UK PLESSEY CODE . L001$ . L008$ ENABLE CHECK DIGIT DOUBLE 11 . L002$ PLUS MOD 10 . L009$ DISABLE CHECK DIGIT SINGLE . L004$ MOD 10 . L005$ CDV & SEND CD MIN LENGTH [ 6 ] .
Page 48
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters.
Page 50
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters.
GROUP-39 SYMBOLOGIES: INTERLEAVED 2 OF 5, CODE 11 . J001$ INTERLEAVED 2 OF 5 . J008$ ENABLE . J002$ First digit suppressed . J009$ DISABLE . J003$ Last digit suppressed . J014$ DISABLE CDV . J004$ NO suppressed . J006$ CDV &...
Page 52
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters.
GROUP-40 SYMBOLOGIES: INDUSTRIAL 2 OF 5, MATRIX 2 OF 5 INDUSTRIAL 2 OF 5 . N001$ . N005$ ENABLE . N002$ CDV & NOT SEND CD DISABLE . N006$ . N003$ MIN LENGTH [ 6 ] DISABLE CDV . N007$ .
Page 54
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters.
GROUP-41 SYMBOLOGIES: CODABAR . I 001$ CODABAR ENABLE . I 007$ . I 002$ CDV & NOT SEND CD . I 008$ DISABLE . I 005$ MIN LENGTH [ 6 ] . I 009$ DISABLE CDV . I 006$ MAX LENGTH [ 48 ] CDV &...
Page 56
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters.
GROUP-42 SYMBOLOGIES: ABC- CODABAR, CX- CODABAR . I 017$ ABC- CODABAR . I 039$ . I 018$ INSERT DATA- ON . I 036$ . I 035$ INSERT DATA- OFF SET INSERT DATA* The data can be any alphanumerics of FULL ASCII Table (GROUP 52-60) ABC-CODABAR (American Blood Commission).
GROUP-43 SYMBOLOGIES: CODABAR COUPLING, ADJACENT REQUIRED CODABAR COUPLING . I 019$ . I 041$ . I 020$ INSERT DATA - ON . I 026$ . I 021$ INSERT DATA - OFF SET INSERT DATA* ABC-Codabar and CX-Codabar have certain rules regarding the Stop Character of first bar code and the stop character of second bar code while in conjunction, while Codabar- Coupling is enabled, the data from any two Codabar bar codes...
GROUP-44 SYMBOLOGIES: STANDARD & FULL ASCII CODE 39, CODE 32 STANDARD CODE 39 . G003$ & FULL ASCII 39 DISABLE CDV . G008$ . G004$ ENABLE . G009$ CDV & SEND CD . G005$ DISABLE . G001$ CDV & NOT SEND CD .
Page 60
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters.
GROUP-46 SYMBOLOGIES: UPC-E SYSTEM NUMBER . H064$ UPC-E0 E [ 0 ] OFF . H063$ E ( 0 ) ON . H065$ UPC-E1 E [ 1 ] ON . H066$ E ( 1 ) OFF NOTE: Most UPC bar codes lead with 0 number systems, for these bar codes use UPC E(0) selection.
GROUP-50 SYMBOLOGIES: EAN/UCC-128, CODE 128 . M001$ EAN/ UCC-128 . M005$ ENABLE . M002$ FUNC 1 CHAR SEND . M006$ DISABLE . M003$ FUNC 1 CHAR NOT SEND CODE ID ENABLE . M007$ . M004$ DEFINE EAN 128 CODE ID DISABLE NOTES: DEFINE EAN 128 The first FNC1 character is translated to ]c1, and the second FNC1 character is translated to an ASCII <GS>...
GROUP-64 TROUBLE SHOOTING Our Barcode Scanners are simple to install and use. Most operational issues can be attributed to: INCORRECT INTERFACE CONNECTION INCORRECT CONFIGURATION SETUP POOR BARCODE QUALITY GENERAL PROCEDURES First, make sure the scanner is firmly connected to the host computer, when attached correctly, the scanner will emit one long beep.
Page 81
GROUP-65 TROUBLE SHOOTING RS232 INTERFACE PROBLEMS Once you read bar code, there is no output on the monitor, the symptoms may be caused by: 1. Have you set the protocol of RS232 like Baud rate, data bits, parity and handshaking etc. of a scanner to match to the PC terminal setting? Solution: reset the above mentioned RS232 protocol of scanner to match to PC protocol.
Page 82
GROUP-66 TROUBLE SHOOTING Is the proper symbology enabled? Each bar code symbology can be individually enabled or disabled. It is suggested that you enable only those that you will be scanning, thereby eliminating the possibility of mis reads from the scanning of other symbologies. Does the selected bar code symbology con guration match the bar code(s) being read? Scanned data from each bar code symbology can be restricted...
APPENDIX 2 Cable Pin Assignment INTERFACES: 1. TTL, Wand Emulation 1.1 ) AMP (D-Sub 9Pin): Signal Data +5VCC 1.2 ) Din 5 male (240 degree): Signal + 5VCC Data 2. Keyboard Interface: Type of connector: 2.1 ) PS/2 Mini Din6 Female: Signal PC Data +5VCC...
Page 88
APPENDIX 2 Cable Pin Assignment 2. Keyboard Interface: Type of connector: 2.3) PC-AT: Din 5 Male: Signal KB-Clk KB-Data +5VCC 2.4) PC-AT: Din 5 Female: Signal PC-Clk PC-Data +5VCC 3.RS232 Interfaces: 3.1) DB9F Signal TXD(Out) RXD(In) CTS(In) RTS(Out) +5VCC 3.2) DB25F Signal RXD(In) TXD(Out)
APPENDIX 3 BAR CODE TEST CHART NARROW WIDE CHAR.GAP DENSITY mm[mil] mm[mil] mm[mil] RATIO MEDIUM 0.25(10) 0.625(25) 0.25(10) 1/2.5 DENSITY MEDIUM DENSITY NW-7 [CODABAR] CODE-39 Interleaved 2of5...
Page 90
APPENDIX 3 BAR CODE TEST CHART NARROW WIDE CHAR.GAP DENSITY mm[mil] mm[mil] mm[mil] RATIO 0.33(13) 0.825(32.5) 0.33(13) 1/2.5 DENSITY LOW DENSITY...