Nice Pop Instructions For Installation, Use And Maintenance Manual

Nice Pop Instructions For Installation, Use And Maintenance Manual

For swing gates

Advertisement

For swing gates
Pop
Instructions and warnings for the fitter
Istruzioni e avvertenze per l'installatore
Instructions et recommandations pour l'installation
Anweisungen und hinweise für den installateur
Instrucciones j advertencias para el instalador
Instrukcja dla instalatora

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pop and is the answer not in the manual?

Questions and answers

Summary of Contents for Nice Pop

  • Page 1 For swing gates Instructions and warnings for the fitter Istruzioni e avvertenze per l’installatore Instructions et recommandations pour l’installation Anweisungen und hinweise für den installateur Instrucciones j advertencias para el instalador Instrukcja dla instalatora...
  • Page 5 PP7024 PP7224...
  • Page 7 Considering the hazards that may exist during the installation and oper- • Connect the control unit only to a power supply line equipped with ation of POP, it is necessary that also the installation be carried out in safety grounding system.
  • Page 8 “WARN- INGS”. 2.1) Preliminary checks Do not use POP to automate a gate that is inefficient and unsafe. • The gate opens and closes without presenting points of friction. The device does not solve faults resulting from incorrect installation •...
  • Page 9 On PP7224: connect the cable from the PP7024 unit to the mammoth terminal. 2.12) Using buffer batteries (Fig. 14) (optional) POP comes complete with housing for buffer batteries (optional). Break open the plastic cap on the control unit box in order to connect the box with the battery.
  • Page 10 However, periodically make sure (at least once provided in the corresponding maintenance schedule. 5.1) Disposal POP is constructed of various types of materials, some of which can 1. Disconnect the automation system from the electric mains. be recycled (aluminium, plastic, electric cables), while others must 2.
  • Page 11 Retain the manual for future use and deliver it to any subse- quent owner of the automation system. However, Nice is not the producer of your automation system, which is • Your automation system is a machine that will faithfully rather the result of a combination of operations carried out by your instal- execute your commands;...
  • Page 12 Only qualified personnel are authorized to carry carefully designed by Nice to make it extremely easy, without any need out checks, maintenance operations and repairs.
  • Page 14 Tel. +39.06.72.67.17.61 Tel. +33.(0)4.42.62.42.52 info@es.niceforyou.com Tel. +86.21.575.701.46 Fax +39.06.72.67.55.20 Fax +33.(0)4.42.62.42.50 Fax +86.21.575.701.44 inforoma@niceforyou.com infomarseille@fr.niceforyou.com info@cn.niceforyou.com www.niceforyou.com Nice Gate is the doors and gate automation division of Nice Nice Screen is the rolling shutters and awnings automation division of Nice...
  • Page 15 control unit POA1 Instructions and warnings for the fitter Istruzioni ed avvertenze per l’installatore Instructions et recommandations pour l’installateur Anweisungen und Hinweise für den Installateur Instrucciones y advertencias para el instalador Instrukcje i uwagi dla instalatora Aanwijzingen en aanbevelingen voor de installateur...
  • Page 16: Table Of Contents

    POA1 Table of contents: page page Product description Programmable functions Direct programming Installation Level one programming, part one Typical system layout Level one programming, part two Preliminary checks Level two functions Electrical connections 2.3.1 Electrical diagram Programming 2.3.2 Description of the connections Programming methods 2.3.3 Notes about connections 7.1.1 Level one programming: functions...
  • Page 17: Product Description

    1) Product description: The POA1 control unit operates on the basis of a current sensitivity The control unit is pre-programmed for the normal functions, while system which checks the load of the motors connected up to it. The more specific functions can be chosen following a simple procedure. system automatically detects travel stops, memorises the running time of each motor and recognises obstacles during normal move- The most important components of the POA1 control unit have been...
  • Page 18: Preliminary Checks

    • The “mechanical stops” must both be able to stop the gate from moving and easily absorb all the kinetic energy accumulated dur- ing movement (if necessary, use the stops for POP motors). • The power supply line must be protected by magneto-thermal and differential switches and equipped with a disconnection device.
  • Page 19 2.3.2) Description of connections Here follows a brief description of the possible control unit output connections: Terminals Function Description L-N- Power supply line mains power supply 1÷3 Motor 2 * M2 motor connection 4÷5 Flashing light Connection of flashing light 24Vd.c. max. 25W 6÷7 Open Gate indicator/Elect.Lock Connection for Open Gate Indicator 24Vac max.
  • Page 20: Stop Type Input

    2.3.4) STOP type input The POA1 control unit can be programmed for two types of STOP Note 1. Any number of NO devices can be connected to each oth- input: er in parallel, with an 8.2KΩ termination resistance (Figure 4). - NC type STOP for connecting up to NC type contacts Note 2.
  • Page 21 PHOTO, PHOTO1 and PHOTO2 connections (The auxiliary input AUX must be programmed as PHOTO2) PHOTO FOTO 1 2 3 4 5 PHOTO 1 FOTO 1 1 2 3 4 5 PHOTO 2 FOTO 2 1 2 3 4 5 2.3.6) Examples of photocell connections with PHOTO and PHOTO1 connections the phototest function.
  • Page 22: Checking The Connections

    2.3.7) Checking the connections WARNING: The next operations involve work being car- 4. If the connections are correct, the LED for the “NC”-type inputs ried out on live circuits. Some parts have mains voltage will be on, while those for the “NO” type inputs must be off. Here running through them and are therefore EXTREMELY DAN- follows Figure 8 illustrating the LEDs on, and the summary table of GEROUS! Pay maximum attention to what you are doing...
  • Page 23: Testing

    3) Testing The automation system must be tested by qualified and • Make sure that the motor switches off when the door reaches the expert staff who must establish which tests to perform mechanical stop. depending on the relative risk. •...
  • Page 24: Level One Programming, Part One

    6.2) Level one programming, part one • Automatic closing: This function features an automatic closing cycle after the pro- • Close after photo: grammed pause time; the pause time is factory set to 20 seconds During the automatic closing cycle, this function reduces the but it can be modified to 5, 10, 20, 40 or 80 seconds.
  • Page 25: Programming

    • Pre-flashing time: If the “current sensitivity” function (together with oth- A manoeuvre warning sign can be activated on the flashing light er vital features) is adjusted correctly, the system will before each manoeuvre begins, and the time programmed to 1, 2, comply with European standards, EN 12453 and EN 4, 6, 8 and 10 seconds.
  • Page 26: Level One Programming: Functions

    7.1.1) Level one programming: functions At level one, the functions can be activated or deactivated. short flashes indicate the function has been deactivated; long flash- At level one, LED P1 is always on; if LEDs L1, L2…L5 are on, the es indicate the function has been activated.
  • Page 27: Memory Deletion

    7.2) Memory deletion Each new programme replaces the previous settings. It is usually As all the functions return to their pre-set values after unnecessary to “delete all” the memory. If required, the memory can the memory is deleted, a new search for the mechanical be totally deleted by performing this simple operation: stops must be carried out.
  • Page 28: Programming Diagram

    7.5) Programming diagram The following figure shows the complete programming diagram of the functions and relative parameters. This figure also shows the functions and parameters either as they were initially or following total memory deletion. Normal operation Led P1 Slow flashing Photo Photo Step step...
  • Page 29: Optional Accessories

    8) Optional accessories • “RADIO” Card The control unit has a connector for fitting a 4 channel radio card • PS124 Buffer Battery complete with SM slot. This remote control device functions by PS124 buffer batteries can be used to supply the control unit in means of transmitters which act on the inputs as per the following case of network blackouts.
  • Page 30 : programmable at 5, 10, 20, 30 and 40 % of working time Leaf delay in close cycle : Automatic detection 2nd motor output : for POP PP7224 motors Maximum cable lengths : electricity supply : 2nd motor : other inputs/outputs 50m...
  • Page 31: Radio Receiver

    smxi smif smxis radio receiver Description of the product SMXI, SMXIS and SMXIF are 4-channel radio receivers for control Mode I. Each transmitter button activates the corresponding output units equipped with SM-type connector. in the receiver, that is, button 1 activates output 1, button 2 activates The peculiarity of compatible transmitters is that the identification output 2, and so on.
  • Page 32 Memorising a remote control When the memorisation phase is activated, any trans- mitter correctly recognised within the reception range of the radio is memorised. Consider this aspect with care and remove the aerial if necessary to reduce the capacity of the receiver. The procedures for memorising the remote controls must be per- formed within a certain time limit;...
  • Page 33 Deleting all transmitters All the memorised codes can be deleted as follows: Table “B4” Deleting all transmitters Example Press the receiver button and hold it down Wait for the Led to light up, then wait for it to switch off and then wait for it to flash 3 times Release the button exactly during the third flash 3°...
  • Page 34 Shanghai Tel. +39.06.72.67.17.61 Tel. +33.(0)4.42.62.42.52 info@es.niceforyou.com Tel. +86.21.575.701.45/46 Fax +39.06.72.67.55.20 Fax +33.(0)4.42.62.42.50 Fax +86.21.575.701.44 inforoma@niceforyou.com info@cn.niceforyou.com www.niceforyou.com Nice Gate is the doors and gate automation division of Nice Nice Screen is the rolling shutters and awnings automation division of Nice...

This manual is also suitable for:

Pop pp7024Pop pp7224

Table of Contents