Full high definition interactive flat panel display (fhd ifpd) 75”(190cm) (33 pages)
Summary of Contents for Hitachi StarBoard T-17SXLG
Page 1
T-17SXLG Safe Handling StarBoard StarBoard T-17SXLG User's Guide How to Request a User's Guide When requesting a separate copy of this user's guide, specify T17-US100601. Read this user’s guide and carefully retain it for future reference. Before using this product, carefully read and fully understand the safety instructions.
Page 2
T-17SXLG Safe Handling StarBoard Notices Reproduction or reprinting, without permission, of this manual or any part thereof is prohibited. The contents of this manual are subject to change without prior notice. Every effort has been made to ensure that this manual is complete and correct. However, should any questionable points, mistakes, etc., come to your attention, please inform the vendor.
Page 3
95.64309G00x (StarBoard T-17SXLG), AH00131 * The term “x” as used in this manual denotes the model No. of the product. The StarBoard T-17SXLG incorporates WALTOP’s 17-inch LCD monitor integrated digitizer technology. Windows is registered trademarks of Microsoft Corporation (U.S.) and in other countries.
Page 4
T-17SXLG Safe Handling StarBoard Safe Handling Markings and Symbols Various markings and symbols are used in this user’s guide and on this product, to ensure the safe and correct use of this product and to prevent personal injury and property damage. These symbols and their meanings are as explained below.
Page 5
T-17SXLG Safe Handling StarBoard Safety Precautions Always comply with them WARNINGS Securely insert the power plug into the Before moving this product, detach the power socket. power plug and the power cable. If it is not plugged in securely, The power cable might be damaged,...
Page 6
T-17SXLG Safe Handling StarBoard Safety Precautions Always comply with them WARNINGS Do not use a power cable other than the Do not open or alter the cabinet of this accessory power cable. product. If a power cable other than the...
Page 7
T-17SXLG Safe Handling StarBoard Safety Precautions Always comply with them WARNINGS In the following cases, unplug the product from the AC Adaptor socket and ask the technical support of Hitachi Software. a. After the power cord or AC Adaptor plug is damaged.
Page 8
T-17SXLG Safe Handling StarBoard Careful thought was given to the cautions on this device and in this user’s guide. However, unanticipated circumstances might occur. When operating this product, users themselves must exercise caution as well as follow instructions. WARNINGS Warning Details Page Use the AC Adaptor supplied with this product.
2.3.2 OSD Adjustment Options..................2-8 3. Appendix ...................... 3-1 3.1 Troubleshooting ....................... 3-1 3.2 System Specifications ...................... 3-4 3.3 How to Take Care of the StarBoard ................. 3-6 3.4 Consumables ........................3-6 3.5 LCD Panel........................3-6 3.6 Provisions of Product Warranty ..................3-7...
Use as soon as the PC is started up (For Windows) The StarBoard can be used as soon as the PC is started up, by just installing the StarBoard Software package included.
(10) Pen tip replacement pin set (11) StarBoard Software x.x (DVD-ROM) (*2) (12) StarBoard T-17SXLG User’s Guide (this manual) (13) StarBoard Software x.x Installation Guide (*2) (14) Warranty Sheet (*1) The quantity of power cable is depended on the region.
(2) Stand (bottom of body and back) (5) Function buttons The stand serves to hold the Eight standard functions used by the StarBoard in place. The LCD angle StarBoard software are assigned to can be adjusted in the range of these buttons. (For details on approx.
Page 13
Introduction StarBoard 1.3.2 Front Switch Panel (1) Power button (4) Menu button This button turns the StarBoard LCD This button is used to display the monitor ON/OFF OSD menu. Press it after making menu selections to apply those. (2) Power indicator...
T-17SXLG Introduction StarBoard 1.3.3 Connector Panel Bottom View of StarBoard Back Right Side (1) Power port (4) Audio input port The AC adapter is connected here. This port is used to output PC audio from the StarBoard speakers. The (2) VGA input port...
Introduction StarBoard 1.4 Assembly and Setup Keep the following points in mind when installing the StarBoard. Select a stable, flat location. Avoid installing in locations that are dusty, extremely hot, cold, or humid. Also avoid installing in locations exposed to direct sunlight.
Use the screen at an easily viewable angle, taking into account external light and ceiling lighting, which may reflect off the screen. 1.4.2 How to Use the Pen Holder The T-17SXLG comes with a pen holder on the back side. Store the stylus pen in the pen holder when not in use. Insert vertically...
StarBoard To power outlet (1) Connect the RGB cable to the VGA input port on the side of the StarBoard, and tighten the screws to fasten. Connect the other end of the cable to the PC VGA port, and tighten the screws to fasten.
Page 19
Use only AC Adaptor or power cables specified by the manufacturer. Use of improper adaptors or cables can damage the product or cause a fire. How to install StarBoard Software For details on how to install StarBoard software, see “StarBoard Software Installation” in StarBoard Software x.x Installation Guide Notice of USB cable Some kind of USB chipset causes the function buttons doesn't work.
Notice when displaying screens at SXGA resolution Be sure to set the monitor refresh rate to 60 Hz if displaying the StarBoard at SXGA resolution (1280 1024). If used at a refresh rate other than 60 Hz, the pen may not operate correctly due to noise from the LCD panel.
If the StarBoard is not connected” message appears, StarBoard Software has not detected the StarBoard. Check whether the StarBoard and PC are connected properly. If they are connected properly, the “StarBoard is connected” message appears. If the indication does not change even though you have checked the connection, there is likely to be some problem.
Usage StarBoard 2.2 Using the Stylus Pen This section describes how to use the StarBoard stylus pen. 2.2.1 How to Use the Stylus Pen The stylus pen has a power switch. Battery life can be pronged by switching the power switch OFF when not in use.
Mouse right-click Secondary button click Button No. 1 Pen tip Side Button No. 1 Side Button No. 0 This function can only be changed in Windows. For details on changing the button settings, see the StarBoard Software x.x Online Help. English...
T-17SXLG Usage StarBoard 2.2.4 Changing the Battery in the Stylus Pen The stylus pen contains a single AAA alkaline dry cell battery. If the pen begins to operate erratically (e.g., if pen input is cut off), change the battery as described below.
T-17SXLG Usage StarBoard (3) Put the stylus pen back together. NOTICE When changing the battery, be careful not to close the pen’s rear part too forcefully. If too much force is applied when closing the rear part of the stylus pen, the pen may be damaged.
StarBoard 2.3 Using the OSD Menu The OSD menu is used when adjusting the StarBoard LCD screen. OSD is an abbreviation for On-Screen Display. The OSD feature allows you to view and adjust the settings for the display on the screen.
T-17SXLG Usage StarBoard 2.3.2 OSD Adjustment Options (1) BRIGHTNESS Used to adjust screen brightness. (0-100) (2) CONTRAST Used to adjust colour contrast. The larger the value, the brighter the image will be. (0-100) (3) LCD ADJUSTMENT CLOCK : Used to adjust screen size. (0-100)
Page 28
T-17SXLG Usage StarBoard (4) COLOUR TEMPRATURE Used to adjust the colour temperature of the screen. (SRGB, 9300K, 7200K, 6500K, 5000K) USER : Used to adjust the red, green, and blue colours of the screen. (0-100) RETURN : Used to return to the previous page.
Page 29
T-17SXLG Usage StarBoard (7) OTHER SETUP SMOOTH : Used to adjust the smoothness of the image. (0-3) OSD H.POSITION : Used to adjust horizontal position of OSD window. (0-100) OSD V.POSITION : Used to adjust vertical position of OSD window. (0-100) OSD TRANSPARENCY : Used to turn OSD window background transparency ON/OFF.
Start up system in proper order. (For the proper order? details on how to start up the system, see ”2.1 Turning the StarBoard On” on page 2-1 of this User’s Guide.) StarBoard Software may be Uninstall StarBoard Software, and then damaged or did not install reinstall.
Page 31
Uninstall StarBoard Software, and damaged or may not be then reinstall. (For details on how to installed correctly. install StarBoard software, see “StarBoard Software Installation ” in StarBoard Software x.x Installation Guide) Is battery worn out? Replace stylus pen battery.
Page 32
Is the StarBoard Software Function button features require the running? StarBoard Software. Use them with the StarBoard Software running. (For details on how to use the StarBoard Software, see the StarBoard Software x.x Installation Guide.) StarBoard Software may be Uninstall StarBoard Software, and damaged or may not be then reinstall.
Appendix StarBoard 3.3 How to Take Care of the StarBoard Please clean your StarBoard periodically so it will continue to work for a long time. (1) Cleaning and care • Use a dry, soft cloth to clean the StarBoard display surface. Do not use detergents.
T-17SXLG Appendix StarBoard 3.6 Provisions of Product Warranty 1. During the free warranty service period, if a malfunction occurs during normal use, the malfunction will be corrected without charge, according to the provisions of the warranty. Furthermore, if the customer registration card accompanying the warranty is not returned to our company, the customer information will not be registered, so free repairs might be unavailable.
Page 37
T-17SXLG Appendix StarBoard In the event of a malfunction in this product caused by the connection to this product of equipment other than the equipment specified by our company. In the event that there is no abnormality in this product, but a defect in a part other than this product was detected or remedied.