Panasonic WJ-HD500A Operating Instructions Manual page 21

Connection with the Extension Units
SCSI Connection
The Digital Disk Recorder WJ-HD500A controls
the extension units through the SCSI chain.
1. Connect the supplied SCSI cable between
the EXT STORAGE port on the WJ-HD500A
and the EXT IN port on the 1st extension
unit.
2. Connect the supplied SCSI cable between
the EXT OUT port on the 1st extension unit
and the EXT IN port on the 2nd extension
unit.
Repeat connections in the same manner for
all additional extension units.
3. The 3rd extension unit must be a WJ-
HDE505 if a further extension unit is con-
nected. Use WJ-HDE500 if the 3rd unit is
located at the end of the SCSI chain.
Up to 6 extension units can be added.
Switch Setting
Data termination and SCSI number settings are required, as
shown below.
1. Set the MODE switch #2 on the rear of the WJ-HD500A
to ON when connecting with an extension unit.
2. Set the SCSI ID number for each unit by pressing the
[–] or [+] button on the rear of the Extension Unit.
0 to 5 are applicable to the extension units.
Note: SCSI ID 6 and 7 are reserved for WJ-HD500A
Disk Recorder.
3. Set the termination switches on the rear of the Extension
Units to ON or OFF.
ON: Is applied to the extension unit located at the end
of the SCSI chain.
OFF: Is used for units other than the end unit.
21
Digital Disk Recorder
IN EXT STORAGE EXT STORAGE
SPOT
OUT
OUT
CONTROL ALARM
MULTI SCREEN OUT AUDIO
16 15 14 13 12 11 10
IN
OUT
16 15 14 13 12 11 10
Extesion Unit #1
WJ-HDE500
SCSI ID = 5
EXT IN EXT IN
EXT OUT EXT OUT
AC IN C IN
PO POWER WER
SCSI ID SCSI ID
TERMINATOR OR TERMINA
ON ON
OFF OFF
SIGNAL GND SIGNAL GND
Extesion Unit #2
WJ-HDE500
SCSI ID = 4
EXT IN EXT IN
EXT OUT EXT OUT
AC IN C IN
POWER PO WER
SCSI ID SCSI ID
TERMINATOR OR TERMINA
ON ON
OFF OFF
SIGNAL GND SIGNAL GND
Extesion Unit #3
WJ-HDE500 or
WJ-HDE 505*
SCSI ID = 3
EXT IN EXT IN
EXT OUT EXT OUT
AC IN C IN
PO POWER WER
SCSI ID SCSI ID
TERMINATOR OR TERMINA
ON ON
OFF OFF
SIGNAL GND SIGNAL GND
* Use a WJ-HDE505 for the 3rd unit position if additional units are installed.
Use a WJ-HDE500 if the 3rd position is the end of the SCSI chain.
WJ-HD500A
SCSI ID = 6 & 7
GEN-LOCK OUT
COPY SIGNAL GND
REMOTE(WV-CU50)
DATA 10/100 BASE-T AC
SERIAL
IN
MODE
9 8 7 6 5 4 3 2 1
ON
OFF
9 8 7 6 5 4 3 2 1
POWER
VIDEO
Extesion Unit #4
WJ-HDE500
SCSI ID = 2
EXT IN EXT IN
EXT OUT EXT OUT
SCSI ID SCSI ID
ON ON
TERMINA TERMINATOR OR
OFF OFF
ON ON
OFF OFF
Extesion Unit #5
EXT IN EXT IN
EXT OUT EXT OUT
SCSI ID SCSI ID
ON ON
OFF OFF TERMINATOR OR TERMINA
ON ON
OFF OFF
Extesion Unit #6
EXT IN EXT IN
EXT OUT EXT OUT
ON ON SCSI ID SCSI ID
OFF OFF TERMINATOR OR TERMINA
ON ON
OFF OFF
1 2 3 4
ON
MODE
SCSI ID
–
1
+
TERMINATOR
ON
OFF
AC IN C IN
POWER PO WER
ON ON
OFF OFF
SIGNAL GND SIGNAL GND
WJ-HD500
SCSI ID = 1
AC IN C IN
PO POWER WER
ON ON
OFF OFF
SIGNAL GND SIGNAL GND
WJ-HD500
SCSI ID = 0
AC IN C IN
PO POWER WER
ON ON
OFF OFF
SIGNAL GND SIGNAL GND