Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Pro-face FP2600-T41
Summary of Contents for Pro-face FP2600-T41
- Page 1 FP2600-T41 User Manual Digital Electronics Corporation...
-
Page 2: Preface
Preface Thank you for purchasing Digital’s TFT type color display panel, the 'FP2600-T41' (hereafter referred to as the FP unit). The FP unit is a TFT type color liquid crystal display monitor for IBM-PC compatible personal computers (SVGA mode). Please read this manual completely to insure the correct use and complete understand- ing of the FP unit's functions. -
Page 3: For The Safe And Correct Use Of This Unit
A reference point. Describes the word or phrase marked by the as- terisk (*) and the corresponding number. Reference pages on related topics. Operational steps. Please follow these numbered steps in order to 1),2) perform the desired operation. FP2600-T41 User Manual... -
Page 4: Warning Safety Instructions
When installing the FP unit, be sure to follow the instructions given in “Chapter 3. Installation and Wiring," to insure it is done correctly. Do not use the FP in an environment with flammable gas since it may cause an explosion. FP2600-T41 User Manual... -
Page 5: Caution Safety Instructions
- use the Display OFF feature, if the same image is to be displayed for a long period of time. - change the screen display periodically to prevent the displaying of a single image for a long period of time. FP2600-T41 User Manual... -
Page 6: Table Of Contents
Warning: Safety Instructions ..................iii Caution: Safety Instructions ..................iv Table of Contents ......................v When Connecting to a PC ................... vii FP2600-T41 Features ....................viii Package Contents ....................... ix UL/c-UL (CSA) Application Notes ................x CE Marking Notes ...................... x Chapter 1—Introduction... - Page 7 3 Touch Panel Does Not Work .................... 5-4 Chapter 6—Maintenance Regular Cleaning ..................... 6-1 1 Cleaning the Display ......................6-1 2 Installation Gasket Check/Replacement ................6-1 Periodic Check Points ..................... 6-2 Replacing the Backlight ................... 6-3 INDEX..................... i - iv FP2600-T41 User Manual...
-
Page 8: When Connecting To A Pc
Some types of VGA equipment may not be within the ranges specified above, and, therefore, cannot be connected to the FP. Also, if the user changes his PC's VGA board, there is the possiblity that the new board may not be able to be connected to the FP. FP2600-T41 User Manual... -
Page 9: Fp2600-T41 Features
Panel can be used as a VGA Display Since the FP2600-T41 is equipped with an analog RGB interface, it can be connected to any PC with standard VGA/SVGA mode. (The PC's clock frequency, however,... -
Page 10: Package Contents
Package Contents The FP's packing box contains the items listed below. Please check to be sure each is included and is not damaged. FP unit (FP2600-T41-24V) FP2500/2600 User Manual (Contained in plastic case) User Manual Installation Gasket (1) Installation Brackets (4) -
Page 11: Ul/C-Ul (Csa) Application Notes
OFF, or the area is known to be non-hazardous. CE Marking Notes The FP2600-T41-24V is a CE marked product that conforms to EMC directives EN55011 class A and EN61000-6-2. *For detailed CE marking information, please contact your local FP distributor. -
Page 12: Chapter 1-Introduction
FP2600-T41 unit Analog RGB Interface Cable (FP-CV00<2.5m>,FP-CV01<5m>) (VGA standard: Dsub 15-pin male) B type USB Interface Cable (5m) (FP-US00) (A-B type Cable) SIO Interface Cable (5m) (FP61V-IS00-O) (Straight Cable: Dsub 9-pin female) A type Personal Computer (PC) FP2600-T41 User Manual... -
Page 13: Optional Equipment
FP. A-B type cable. Backlight PS600-BU00 Replacement Backlight bulbs . Bulbs Installation Maintenance GP070-AT01 Metal installation brackets for FP2600-T41 Brackets Parts Replacement rubber gasket, used when Rubber GP-WP10-MS installing the FP. Same as the FP's Gasket original gasket. Provides disposable screen protection from Cover dust and other elements. -
Page 14: Chapter 2-Specifications
Pulse length: 1 µ s Rise time (rise/fall): 1 ns Pollution Level Not immune to corrosive gas Grounding Less than 100 Ω , or your country's applicable standard Protection*1 Equivalent to IP65f (JEM1030) (See the next page's note) FP2600-T41 User Manual... -
Page 15: Structural Specifications
To maintain the original protection level, you need to replace the installation gasket regularly. 2-1-3 Structural Specifications DC24V (FP2600-T41) External Dimensions 317W x 243H x 58D mm Weight 3.5 kg or less Cooling System Natural air circulation FP2600-T41 User Manual... -
Page 16: Functional Specifications(For Dc24V)
2) at *1 The brightness at central part of the screen when displaying all white. *2 2.5 times decreased brightness may be the life span, but this value is only for reference and not a guaranteed value. FP2600-T41 User Manual... -
Page 17: Interface Specifications(For Dc24V)
31.469±1 KHz 70±1 Hz 28.322M H z±1% • With vertical 350 pixels, 400 pixels, including 50 pixels at the top and at the bottom of the screen will be enlarged and displayed at 600 pixels (1.5 times). FP2600-T41 User Manual... - Page 18 NC (spare for input) Reserved NC (spare for input) H. SYNC Horizontal synchronous signal input V. SYNC Vertical synchronous signal input Reserved NC (spare for input) Connector: Mini Dsub 15 pin type Connector set screw: Inch type (4-40) FP2600-T41 User Manual...
-
Page 19: Serial Interface
Therefore, connect each pin's signal to the same signal name on the PC side. For example, pin #2 'RD' should be connected to the 'RD' input terminal on the PC's connector. Refer to section "2-4 Cable Diagrams" for each signal's direction. FP2600-T41 User Manual... -
Page 20: Usb Interface
Specifications 2-3-3 USB Interface Pin Assignments and Signal Names for USB Interface Signal Condition Pin Location Name 1 USB1-5V +5VIN 2 USBD1(-) USBdata(-) 3 USBD1(+) USBdata(+) 4 GND Ground Communication Low speed Device Connector: B type connector FP2600-T41 User Manual... -
Page 21: Cable Diagrams
Specifications Cable Diagrams 2-4-1 RGB Interface Cable Pin Connections FP side RGB cable PC side RED VIDEO Output RED VIDEO Analog R Input RED IN Analog G Input GRIN IN GRN VIDEO Output GRN VIDEO Analog B Input BLU IN BLU VIDEO Output BLU VIDEO... -
Page 22: Pin Connections For The Sio Interface Cable
Specifications 2-4-2 Pin Connections for the SIO Interface Cable FP side SIO cable PC side Output Input Output Input Input Output Input Output GND 5 GND 5 Output DSR 6 Input DSR 6 Input Output Output Input Input Signal names for the FP's SIO interface are designed to match the same pin order as the SIO interface on a standard PC. -
Page 23: Names And Functions Of Fp Parts
Used for both sending touch panel data to the host, and receiving commands from the host. H: Front LED An LED to detect power supply, backlight burning out and input of image signal. 3-3-2 Front LED Operation Mode Display 2-10 FP2600-T41 User Manual... -
Page 24: Flat Panel (Fp) Dimensions
Specifications 2-6 Flat Panel (FP) Dimensions 2-6-1 External Dimensions ( DC24V ) Unit: mm [in.] 301.0 [11.85] 317 [12.48] 58 [2.28] 8 [0.31] Side Front FP2600-T41 User Manual 2-11... -
Page 25: Installation Brackets
Specifications 2-6-2 Installation Brackets Unit: mm [in.] 16[0.63] 31[1.22] 19.5[0.77] 2-6-3 FP Installation Dimensions Unit: mm [in.] Panel +0.04 301.5 [11.87 2-12 FP2600-T41 User Manual... -
Page 26: Chapter 3-Installation And Wiring
Chapter 2-6-3 "FP Installation Dimensions". Panel Panel Cut • It is important that the panel surface is flat, clean, and has no jagged edges. • The Panel thickness should be between 1.6mm and 10.0mm. 1.6 to 10mm FP2600-T41 User Manual... - Page 27 • Check that heat from surrounding equipment will not cause the FP to overheat. • Do not use the FP2600-T41 in an environment that exceeds 50 • Ensure this unit is located as far away as possible from electromagnetic circuits, non-fuse type breakers, and other equipment that can cause arcing.
- Page 28 (total: 4 slots) Insertion Slots Bottom 3) Insert each of the fasteners shown below. Be sure to pull the fastener back until it is flush with the rear of the attachment hole. FP2600-T41 User Manual...
- Page 29 4) Use a Phillips screw driver to tighten each fastener screw and secure the FP in place. Do not use too much force, since it may damage the FP unit. A torque of only 0.5 N•m is sufficient to tighten these screws. FP2600-T41 User Manual...
-
Page 30: Power Cable Connection
• To prevent electrical shocks, be sure the Power Cable is plugged first into the FP unit, then into the wall (main supply). • Your FP2600-T41 -24V uses input voltage of only DC24V. If your power supply is greater than that required by your unit, it may damage both the power source and the FP unit. -
Page 31: Precaoutions: Connecting The Power Supply
• Be sure to ground the surge absorber (E1) separately from the GP unit (E2). FP unit • Select a surge absorber that has a maximum circuit volt- age greater than that of the lightening peak voltage of the power surge supply. absorber FP2600-T41 User Manual... -
Page 32: Precautions: Grounding
3-2-4 Precautions: Input/Output Signal Lines Input and output signal lines must be separated from operating circuit power cables. If this is not possible, use a shielded cable and connect the shield to the FP chassis. FP2600-T41 User Manual... -
Page 33: Operation Mode Setup And Display Positioning
3-3 Operation Mode Setup and Display Positioning 3-3-1 Operation Mode Setup and Adjustment The setup switches (dip-switches) are located in the rear of the unit. FP2600-T41 (rear view) Dip-switch The default settings for the FP were created based on the standard connection method used with IBM-PCs. -
Page 34: Front Led Option Mode Display
Pow er O N Pow er O N P a n e l N orm al N orm al Bulb burned out Bulb burned out Ba cklig h t Im a g e in p u t FP2600-T41 User Manual... -
Page 35: Display Position Compensation By Osd
2) Main Menu The left illustrations are the main menu of OSD. By touching the characters on the display screen, you can switch to that screen adjustment mode. Touching the ESC key will exit OSD mode. FP2600-T41 User Manual 3-10... - Page 36 Phase adjustment : The function to compensate the flicker. Dimmer function : The function to compensate the flicker of backlight. Setup value clear : Returns all setup values to default values. Closes the OSD. Saves the setup values. FP2600-T41 User Manual 3-11...
- Page 37 ALLCLEAR screen. When you push START, all setup data of the adjustment items will be returned to START default value (factory set up value). By pushing the ESC key, you will return to the main menu. FP2600-T41 User Manual 3-12...
-
Page 38: Chapter 4-Touch Panel Commands
65h / 67h Display ON 66h / 68h Display OFF Click sound (high) ON Click sound (high) OFF Click sound (low) ON Click sound (low) OFF Buzzer (high) ON Buzzer (high) OFF Buzzer (low) ON Buzzer (low) OFF FP2600-T41 User Manual... -
Page 39: Boot-Up Initialization
Parity 1 bit Stop bit Initializes the system default values. Default Setting Function Display output Backlight ON or OFF selected with Dip SW1-6 (high) Click sound Buzzer ON or OFF selected with Dip SW1-5 Automatic OFF mode FP2600-T41 User Manual... -
Page 40: Touch Interface Data
800 x 600 becomes necessary. Also, a calibration program to adjust the actual touch position is needed. As a result, the following software is included with the FP2600-T41 unit. OS and Touch Panel Driver Combinations... - Page 41 11h 0h 17h 1h F4h 11h 0h 17h 1h F4h 10h when released, only 1 unit of data is sent (3) Sampling Rate A maximum of 87 points per second. FP2600-T41 User Manual...
- Page 42 65h ( e ) / 67h ( g ) RS232C 65h ( e ) / 67h ( g ) Turns on FP2600-T41's display. Backlight is also turned on simultaneously. Display OFF 66h ( f ) / 68h ( h )
- Page 43 If the following three commands are sent at the same time... Buzzer (high) ON Buzzer (low) ON Click sound (high) ON ... the Buzzer (high) activates. However, when the Buzzer (high) OFF command is sent afterwards, the Buzzer (low) will activate. FP2600-T41 User Manual...
- Page 44 Touch Panel Commands Reserved The following commands are reserved. If these commands are used, they are sometimes treated as errors. Reserved FP2600-T41 User Manual...
- Page 45 Touch Panel Commands MEMO FP2600-T41 User Manual...
-
Page 46: Chapter 5-Troubleshooting
OFF and wear gloves. This section assumes that the FP is the cause of a problem, not the host. When the host is the problem, please refer to its corresponding manual. FP2600-T41 User Manual... -
Page 47: No Display
Has the 11V unit's Change the backlight if it has burnt out. backlight (CFL) been set Chapter 7-3 Replacing up correctly? the Backlight. There is a problem with the FP unit. Please contact your local FP distributor. FP2600-T41 User Manual... - Page 48 Setup and Display Positioning. Adjust the screen display position. Chapter 3-3 Operation Does the screen display Mode Setup and Display Position- correctly? ing. There is a problem with the FP unit. Please contact your local FP distributor. FP2600-T41 User Manual...
-
Page 49: Touch Panel Does Not Work
Touch panel not working Connect the SIO or USB cable Is the SIO or USB cable correctly. connected correctly? 2-4 Cable Diagrams There is a problem with the FP unit. Please contact your local FP distributor. FP2600-T41 User Manual... -
Page 50: Chapter 6-Maintenance
Be sure to change the gasket at least once a year, or when scratches or dirt become visible. Installation Gasket Attachment Procedure (all units) 1) Place the FP on a flat, level surface facing the display face downwards. 2) Remove the gasket from the FP2600-T41 User Manual... - Page 51 Related Items • Are all power cords and cables connected properly? Have any become loose? • Are all mounting brackets holding the unit securely? • Are there many scratches or traces of dirt on the installation gasket? FP2600-T41 User Manual...
-
Page 52: Replacing The Backlight
When the unit’s backlight burns out, the unit’s status LED will brink green/red or orange. FP2600-T41 units use a CFL, long-life type backlight. The actual life of the back- light however, will vary depending on the FP’s operating conditions, and replacement may be required. - Page 53 Maintenance MEMO FP2600-T41 User Manual...
-
Page 54: Index
Input Voltage 2-1, 3-5 Display Position Compensation by OSD 3-10 Insertion Slot 3-3 Dot Pitch 2-3 Installation 3-1 Installation Gasket ix, 3-1, 6-1 Installation Guide ix Installation brackets ix, 1-2, 2-12, 3-3 Interface Specifications 2-4 Internal buffer 4-2 IP65F 2-1 FP2600-T41 User Manual... - Page 55 Precautions: Grounding 3-7 UL508 x Precautions: Input/Output Signal Lines 3-7 UL Registration Model x Precautions: Power Supply 3-6 User Manual ix Priority USB Interface 2-7, 2-10 Buzzer and Click sounds 4-6 USB Interface Cable 1-1, 1-2, 2-9 FP2600-T41 User Manual...
- Page 56 Vertical Installation 3-2 Vertical display adjustment 3-11, 3-12 Vibration Endurance 2-1 Voltage Transformer 3-6 Weight 2-2 Wiring 3-5 Grounding 3-7 Input/Output Signal Lines 3-7 Power Cable 3-5 Power Supply 3-6 When Connecting to a PC vii FP2600-T41 User Manual...
- Page 57 MEMO FP2600-T41 User Manual...