Preface Thank you for purchasing Digital’s TFT type color display panel, the 'FP2600-T11' (hereafter referred to as the FP unit). The FP unit is a TFT type color liquid crystal display monitor for IBM-PC compatible personal computers (SVGA mode). Please read this manual completely to insure the correct use and complete understand- ing of the FP unit's functions.
A reference point. Describes the word or phrase marked by the as- terisk (*) and the corresponding number. Reference pages on related topics. Operational steps. Please follow these numbered steps in order to 1),2) perform the desired operation. FP2600-T11 User Manual...
When installing the FP unit, be sure to follow the instructions given in “Chapter 3. Installation and Wiring," to insure it is done correctly. Do not use the FP in an environment with flammable gas since it may cause an explosion. FP2600-T11 User Manual...
- use the Display OFF feature, if the same image is to be displayed for a long period of time. - change the screen display periodically to prevent the displaying of a single image for a long period of time. FP2600-T11 User Manual...
Some types of VGA equipment may not be within the ranges specified above, and, therefore, cannot be connected to the FP. Also, if the user changes his PC's VGA board, there is the possiblity that the new board may not be able to be connected to the FP. FP2600-T11 User Manual...
Panel can be used as a VGA Display Since the FP2600-T11 is equipped with an analog RGB interface, it can be connected to any PC with standard VGA/SVGA mode. (The PC's clock frequency, however,...
Package Contents The FP's packing box contains the items listed below. Please check to be sure each is included and is not damaged. FP unit (FP2600-T11) FP2500/2600 User Manual (Contained in plastic case) User Manual Installation Gasket (1) Installation Brackets (4)
FP2600-T11 unit Analog RGB Interface Cable (FP-CV00<2.5m>,FP-CV01<5m>) (VGA standard: Dsub 15-pin male) B type USB Interface Cable (5m) (FP-US00) (A-B type Cable) SIO Interface Cable (5m) (FP61V-IS00-O) (Straight Cable: Dsub 9-pin female) A type Personal Computer (PC) FP2600-T11 User Manual...
FP. A-B type cable. Backlight PS600-BU00 Replacement Backlight bulbs . Bulbs Installation Maintenance GP070-AT01 Metal installation brackets for FP2600-T11 Brackets Parts Replacement rubber gasket, used when Rubber GP-WP10-MS installing the FP. Same as the FP's Gasket original gasket. Provides disposable screen protection from Cover dust and other elements.
Pulse length: 1 µ s Rise time (rise/fall): 1 ns Pollution Level Not immune to corrosive gas Less than 100 Ω , or your country's applicable standard Grounding Protection*1 Equivalent to IP65f (JEM1030) (See the next page's note) FP2600-T11 User Manual...
To maintain the original protection level, you need to replace the installation gasket regularly. 2-1-3 Structural Specifications AC100V (FP2600-T11) External Dimensions 317W x 243H x 58D mm Weight 3.5 kg or less Cooling System Natural air circulation FP2600-T11 User Manual...
2) at *1 The brightness at central part of the screen when displaying all white. *2 2.5 times decreased brightness may be the life span, but this value is only for reference and not a guaranteed value. FP2600-T11 User Manual...
70± 1 Hz 28.322M H z± 1% • With vertical 350 pixels, 400 pixels, including 50 pixels at the top and at the bottom of the screen will be enlarged and displayed at 600 pixels (1.5 times). FP2600-T11 User Manual...
Page 18
NC (spare for input) Reserved NC (spare for input) H. SYNC Horizontal synchronous signal input V. SYNC Vertical synchronous signal input Reserved NC (spare for input) Connector: Mini Dsub 15 pin type Connector set screw: Inch type (4-40) FP2600-T11 User Manual...
Therefore, connect each pin's signal to the same signal name on the PC side. For example, pin #2 'RD' should be connected to the 'RD' input terminal on the PC's connector. Refer to section "2-4 Cable Diagrams" for each signal's direction. FP2600-T11 User Manual...
Specifications 2-3-3 USB Interface Pin Assignments and Signal Names for USB Interface Signal Condition Pin Location Name 1 USB1-5V +5VIN 2 USBD1(-) USBdata(-) 3 USBD1(+) USBdata(+) 4 GND Ground Communication Low speed Device Connector: B type connector FP2600-T11 User Manual...
SENSE(MONO) SENSE(MONO) H.SYNC Input HSYN HSYN Output HSYN V.SYNC Input VSYN VSYN Output VSYN Reserved Signal names for the FP's RGB interface are designed to match the same pin order as the RGB interface on personal computers. FP2600-T11 User Manual...
Used for both sending touch panel data to the host, and receiving commands from the host. H: Front LED An LED to detect power supply, backlight burning out and input of image signal. 3-3-2 Front LED Operation Mode Display 2-10 FP2600-T11 User Manual...
Chapter 2-6-3 "FP Installation Dimensions". Panel Panel Cut • It is important that the panel surface is flat, clean, and has no jagged edges. • The Panel thickness should be between 1.6mm and 10.0mm. 1.6 to 10mm FP2600-T11 User Manual...
Page 27
• Check that heat from surrounding equipment will not cause the FP to overheat. • Do not use the FP2600-T11 in an environment that exceeds 50 • Ensure this unit is located as far away as possible from electromagnetic circuits, non-fuse type breakers, and other equipment that can cause arcing.
Page 28
(total: 4 slots) Insertion Slots Bottom 3) Insert each of the fasteners shown below. Be sure to pull the fastener back until it is flush with the rear of the attachment hole. FP2600-T11 User Manual...
Page 29
4) Use a Phillips screw driver to tighten each fastener screw and secure the FP in place. Do not use too much force, since it may damage the FP unit. A torque of only 0.5 N•m is sufficient to tighten these screws. FP2600-T11 User Manual...
• To prevent electrical shocks, be sure the Power Cable is plugged first into the FP unit, then into the wall (main supply). • Your FP2600-T11 uses input voltage of only AC100V. If your power supply is greater than that required by your unit, it may damage both the power source and the FP unit.
4) Replace the plastic terminal cover. 3-2-2 Precautions: FP2600-T11 Power Supply Please pay special attention to the following points when connecting the power cable to the Power Terminal Block at the back of the FP2600-T11 unit. • If the supplied voltage exceeds the FP...
3-2-4 Precautions: Input/Output Signal Lines Input and output signal lines must be separated from operating circuit power cables. If this is not possible, use a shielded cable and connect the shield to the FP chassis. FP2600-T11 User Manual...
3-3 Operation Mode Setup and Display Positioning 3-3-1 Operation Mode Setup and Adjustment The setup switches (dip-switches) are located in the rear of the unit. FP2600-T11 (rear view) Dip-switch The default settings for the FP were created based on the standard connection method used with IBM-PCs.
2) Main Menu The left illustrations are the main menu of OSD. By touching the characters on the display screen, you can switch to that screen adjustment mode. Touching the ESC key will exit OSD mode. FP2600-T11 User Manual 3-10...
Page 36
Phase adjustment : The function to compensate the flicker. Dimmer function : The function to compensate the flicker of backlight. Setup value clear : Returns all setup values to default values. Closes the OSD. Saves the setup values. FP2600-T11 User Manual 3-11...
Page 37
ALLCLEAR screen. When you push START, all setup data of the adjustment items will be returned to START default value (factory set up value). By pushing the ESC key, you will return to the main menu. FP2600-T11 User Manual 3-12...
65h / 67h Display ON 66h / 68h Display OFF Click sound (high) ON Click sound (high) OFF Click sound (low) ON Click sound (low) OFF Buzzer (high) ON Buzzer (high) OFF Buzzer (low) ON Buzzer (low) OFF FP2600-T11 User Manual...
Stop bit 1 bit Initializes the system default values. Function Default Setting Display output Backlight Click sound ON or OFF selected with Dip SW1-6 (high) Buzzer Automatic OFF mode ON or OFF selected with Dip SW1-5 FP2600-T11 User Manual...
800 x 600 becomes necessary. Also, a calibration program to adjust the actual touch position is needed. As a result, the following software is included with the FP2600-T11 unit. OS and Touch Panel Driver Combinations...
Page 41
11h 0h 17h 1h F4h 11h 0h 17h 1h F4h 10h when released, only 1 unit of data is sent (3) Sampling Rate A maximum of 87 points per second. FP2600-T11 User Manual...
Page 42
65h ( e ) / 67h ( g ) RS232C 65h ( e ) / 67h ( g ) Turns on FP2600-T11's display. Backlight is also turned on simultaneously. Display OFF 66h ( f ) / 68h ( h )
Page 43
If the following three commands are sent at the same time... Buzzer (high) ON Buzzer (low) ON ... the Buzzer (high) activates. However, when the Buzzer (high) OFF command is sent afterwards, the Buzzer (low) will activate. FP2600-T11 User Manual...
Page 44
Touch Panel Commands Reserved The following commands are reserved. If these commands are used, they are sometimes treated as errors. Reserved FP2600-T11 User Manual...
Page 45
Touch Panel Commands MEMO FP2600-T11 User Manual...
OFF and wear gloves. This section assumes that the FP is the cause of a problem, not the host. When the host is the problem, please refer to its corresponding manual. FP2600-T11 User Manual...
Has the 11V unit's (CFL). Change the backlight if it has backlight (CFL) been set burnt out. Chapter 7-3 up correctly? Replacing the Backlight. There is a problem with the FP unit. Please contact your local FP distributor. FP2600-T11 User Manual...
Page 48
Setup and Display Positioning. Adjust the screen display position. Chapter 3-3 Operation Does the screen display Mode Setup and Display Position- correctly? ing. There is a problem with the FP unit. Please contact your local FP distributor. FP2600-T11 User Manual...
Touch panel not working Connect the SIO or USB cable Is the SIO or USB cable correctly. connected correctly? 2-4 Cable Diagrams There is a problem with the FP unit. Please contact your local FP distributor. FP2600-T11 User Manual...
Be sure to change the gasket at least once a year, or when scratches or dirt become visible. Installation Gasket Attachment Procedure (all units) 1) Place the FP on a flat, level surface facing the display face downwards. 2) Remove the gasket from the FP2600-T11 User Manual...
Page 51
Related Items • Are all power cords and cables connected properly? Have any become loose? • Are all mounting brackets holding the unit securely? • Are there many scratches or traces of dirt on the installation gasket? FP2600-T11 User Manual...
When the unit’s backlight burns out, the unit’s status LED will brink green/red or orange. FP2600-T11 units use a CFL, long-life type backlight. The actual life of the backlight however, will vary depending on the FP’s operating conditions, and replacement may be required.
Page 53
Maintenance MEMO FP2600-T11 User Manual...
Display Position Compensation by OSD 3-10 Input Voltage 2-1, 3-5 Dot Pitch 2-3 Insertion Slot 3-3 Installation 3-1 Installation Gasket ix, 3-1, 6-1 Installation Guide ix Installation brackets ix, 1-2, 2-12, 3-3 Interface Specifications 2-4 Internal buffer 4-2 IP65F 2-1 FP2600-T11 User Manual...
Page 55
Buzzer and Click sounds 4-6 Vibration Endurance 2-1 Voltage Transformer 3-6 Rubber gasket 1-2, 3-1 Weight 2-2 Wiring 3-5 Grounding 3-7 Input/Output Signal Lines 3-7 Power Cable 3-5 Power Supply 3-6 When Connecting to a PC vii FP2600-T11 User Manual...