Related Manuals for Colortrac Flatbed 24120
Summary of Contents for Colortrac Flatbed 24120
- Page 1 INSTALLATION and OPERATING MANUAL Colortrac Flatbed 24120 Revised Jan 2004 PAS119 info@colortrac.com http://www.colortrac.com...
- Page 2 Colortrac Ltd. Colortrac Ltd makes no warranty claims with respect to this documentation and disclaims any implied warranties of merchantability or fitness for a particular purpose. The information contained in this document is subject to change without notice.
-
Page 3: Table Of Contents
Colortrac Flatbed Operator Manual. Table of Contents INTRODUCTION................3 SAFETY ....................4 EMC C A................4 LASS INSTALLATION................. 5 ............5 NPACKING AND NSTALLATION ............5 CANNER ABLING AND 3.2.1 Installation using IEEE 1394/Firewire ........5 3.2.2 Installation using ultra wide SCSI ........... 5 OPERATION OF SCANNER.............. -
Page 4: Introduction
Windows operating system and the ScanWorks PC software. The operation of ScanWorks is described using 'Hot Tips' within the software. The Colortrac Flatbed scanner must NOT be installed by an end user. The flatbed will almost always need re-aligning after shipment and this can only be done an Colortrac engineer or one of it's approved distributors/ resellers who have been suitably trained on this product by Colortrac. -
Page 5: Safety
The scanner weighs approx. 120 Kg and will require a minimum of two people to lift it. No attempt should be made by a single person to lift it as serious back damage is likely. Colortrac Ltd recommend that in the interests of safety four adults should be used to move the scanner once unpacked. -
Page 6: Installation
This is to be carried out by a Colortrac engineer or approved distributor/ reseller. Any attempt to install this scanner by the user will invalidate the warranty. If the scanner needs to moved to a different then a Colortrac engineer will need to be contacted to arrange for movement. -
Page 7: Operation Of Scanner
The scanner is now ready for use. As the scanner has multiple cameras, on initial installation Colortrac Ltd recommends that the operator runs an auto-stitch and re-calibrated, for details on how to do this see section 6. -
Page 8: Control Panel
Colortrac Flatbed Operator Manual. Control Panel The display on the bottom right hand corner of scanner indicates its status. The Forward and Reverse buttons allow the scan head to be moved along the length of the scan path. Advance Button... -
Page 9: Maintenance
MAINTENANCE Left/ Right and Front/ Back Stitch Unlike the previous Colortrac models, the Flatbed 24120 doesn't have an auto-stitch. Therefore a manual stitch procedure is required. Place stitch target on scanner face down with bottom edge of target nearest narrow black strip of glass. -
Page 10: Colour Calibration
Colortrac Flatbed Operator Manual. COLOUR CALIBRATION The scanner will need to be colour calibrated after 30 minutes of being switched on. This ensures that the scanner produces the correct colours across the scan. This can be carried out automatically by positioning the Calibration Target over the scan head making sure that the tubes are in the centre of the target (see below). -
Page 11: Trouble Shooting
Colortrac Flatbed Operator Manual. TROUBLE SHOOTING Lights on scanner control panel fail to come on Check that the power supply is connected to the scanner. Check that the scanner is switched on. Error symbol on the display panel indicates a failure during power up Scanner needs re-calibrating. -
Page 12: Specification
Colortrac Flatbed Operator Manual. SPECIFICATION Colortrac Flatbed 24120 Features: 24-bit RGB mode 8-bit greyscale 4-bit indexed colour palette 1-bit binary (b/w) Resolution: 50 to 3600 in 1dpi increments 600 dpi optical resolution Imaging Technology: 3 tri-linear CCD cameras 2 x 7,500 pixels each Scan Area: 841mm x 594mm or 24"... -
Page 13: 10 Declaration Of Conformity
Colortrac Flatbed Operator Manual. 10 DECLARATION OF CONFORMITY Manufacturer: Colortrac Ltd Kings Hall St Ives Business Park St Ives Cambridgeshire, PE17 4WY United Kingdom Details Of Electrical Equipment Model Number: Colortrac Flatbed 24120 Description: Large Format Colour Document Scanner Directives this equipment complies with:...
Need help?
Do you have a question about the Flatbed 24120 and is the answer not in the manual?
Questions and answers