Subscribe to Our Youtube Channel
Related Manuals for Siqura MD20
Summary of Contents for Siqura MD20
- Page 1 Installation Manual Siqura MD20 Indoor Vandal Proof IP Mini PTZ Dome Camera MD20 Second draft...
-
Page 3: Table Of Contents
Contents CONTENTS PREFACE ......................1 CAUTIONS.......................3 OVERVIEW ......................5 3.1.................5 ENERAL PERATION EQUIREMENTS PACKAGE CONTENTS ..................7 DOME SETUP AND CABLE CONNECTION...............9 5.1............9 REPARATIONS FOR NDOOR AMERA ETUP 5.1.1. Switch definition ................... 10 5.1.2. Communication switch configuration ............11 5.1.3. Dome ID configuration ................11 5.1.4. - Page 4 Contents APPENDIX A: CAMERA ACCESSORIES ................. 37 .................... 38 OUNTING CCESSORIES ..................40 OUNTS AND OUNTING OXES APPENDIX B: TECHNICAL SPECIFICATIONS ..............47...
-
Page 5: Preface
All specifications are subject to change without notice. Notice To work with the Siqura MD20 camera, an installer or technician must have the following minimum qualifications: A basic knowledge of CCTV systems and components. - Page 6 Preface Regulations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 7: Cautions
Cautions CAUTIONS Handle the camera carefully. Do not abuse the camera. Avoid striking, shaking, etc. as the camera can be damaged by improper handling or storage. Install electrical wiring carefully. Ask a qualified electrician to perform the wiring for the installation. Please note that input electricity to the unit is at a tolerance of 24VAC 50/60 Hz ±... -
Page 9: Overview
General Operation Requirements A minimum of one control device is required for operation, such as a control keyboard, a DVR or a PC. The Siqura MD20 camera contains a built-in receiver that decodes commands originating from a control device communicating via Ethernet. -
Page 11: Package Contents
Before proceeding, please verify that the box contains the items listed here; the lens is not included. If any item is missing or has defects, DO NOT install or operate the product. Contact your dealer for assistance. Siqura MD20 - Indoor Vandal Proof Mini PTZ Dome Hard Ceiling Mount and 30-cm Cable Harness for... -
Page 13: Dome Setup And Cable Connection
5.1. Preparations for Indoor Dome Camera Setup This installation procedure is for the Siqura MD20 indoor dome camera. Follow the steps below to complete dome housing installation. To prepare the camera Unpack the dome package and take out the dome body. -
Page 14: Switch Definition
Reserved. Must be set to 29. RJ-45 connector. 22-pin connector. Reserved. Figure 5.2 Switches – MD20 (Indoor Dome) Table 5.1 Switch definitions please note Switch A has two buttons. Only the button closest to the 22-pin connector is used to restore factory server defaults. The other button is reserved. -
Page 15: Communication Switch Configuration
Dome Setup and Cable Connection 5.1.2. Communication switch configuration Table 5.2 shows the function of each pin within the Communication Switch: Communication Switch Switch Description SW 1 SW 2 Reserved SW 3 SW 4 Line lock switch SW 5 Reserved SW 6 Table 5.2 Communication switch descriptions Switches 1, 2, 3, 5, and 6 are reserved. -
Page 16: Establishing A Network Connection
Dome Setup and Cable Connection 5.2. Establishing a Network Connection The factory-set IP address of the Siqura MD20 camera is in the 10.x.x.x range. You will find it printed on a sticker on the bottom of the camera. please note This is the address the module will revert to if you issue a ‘Reset to factory... - Page 17 Dome Setup and Cable Connection Click Properties Figure 5.5 Opening IP settings on the host PC In the Internet Protocol (TCP/IP) Properties dialog, click Use the following IP address Enter an IP address that will assign your PC to the same subnet as the camera (i.e., within the 10.x.x.x range).
-
Page 18: Dome Cable Definition And Requirements
Do not forget to save and reboot the camera after changing the settings. 5.3. Dome Cable Definition and Requirements For operation, the Siqura MD20 camera requires an Ethernet cable to carry the signals to a remote viewing site and a cable to power the dome. -
Page 19: Cable Requirements
Dome Setup and Cable Connection 5.3.1. Cable requirements For operation, the camera requires video and cable harness as described below: • A cable to provide 24VAC power supply to the dome. • A CAT-5 Ethernet cable. • Optional audio cables. •... -
Page 20: 22-Pin Connector Definition
Dome Setup and Cable Connection 5.3.4. 22-pin connector definition With the 22-pin connector, installers can simply connect the power and video cables to the dome at once. Particularly, the alarm pins are serviceable for connecting alarm input and output devices, such as alarm sensors, sirens or flashing lights with the surveillance system. For the definition of each pin, please refer to the table below. -
Page 21: Dome Installation
Dome Installation DOME INSTALLATION Based on the user’s installation environment, the Siqura MD20 dome camera can be installed on ceiling, wall or pole. In the following sections, various indoor dome installation methods and procedures are described in detail. 6.1. Installation Scenarios Choose your installation scenario from the list below for complete instructions for performing that installation. -
Page 22: Dome Dimensions
Figure 6.1 Siqura MD20 (Indoor dome) dimensions 6.3. Ceiling Mount Generally, there are four ceiling mounting methods for the Siqura MD20 indoor dome camera: • Hard ceiling mounting described in section 6.3.1 • In ceiling mounting described in section 6.3.2 •... -
Page 23: Hard Ceiling Mounting
Dome Installation 6.3.1. Hard ceiling mounting Hard Ceiling Mounting is a standard installation for an indoor dome, and general mounting accessories are equipped in the standard indoor dome camera package. The items and tools needed to mount the dome camera onto the ceilings are listed below. The supplied items are found in the dome camera package. -
Page 24: In-Ceiling Mounting
Dome Installation Thread the cable harness and Ethernet cable through the center hole of the Mount and connect the cables to the dome body. Attach the dome body to the Mount and rotate the dome body clockwise. Tighten the fixing screw on the fixing plate. - Page 25 • Tool for cutting a circle on the ceiling • Screwdrivers (slotted and Phillips) To install the Siqura MD20 camera with T-Bar Ceiling mount accessory for in-ceiling mounting Screw the T-Bar Body Holder, which is equipped with the T-Bar, onto the dome back, as shown in the figures.
- Page 26 Dome Installation Rotate the T-Bar’s wings to fix the T- Bar at the edge of the ceiling opening. Tighten the screws on the wings. Connect the cable harness and Ethernet cable to the dome body through the center hole of the bracket. Mount the dome body onto the bracket and rotate it clockwise.
-
Page 27: In-Ceiling Mounting With Ceiling Panel
Dome Installation Attach the decorative ring to the T-Bar. Completion 6.3.3. In-ceiling mounting with ceiling panel To mount the dome camera to a suspended ceiling with the T-Bar, employ the ceiling panel, as shown in figure 6.3. Figure 6.3 Employing the ceiling panel To install in a ceiling panel Cut the ceiling panel in half. -
Page 28: Ceiling Mounting With Straight Tube
Dome Installation 6.3.4. Ceiling mounting with straight tube The straight tube is available in 25 cm and 30 cm lengths. Figure 6.4 Ceiling Mount: Straight Tube Items Needed: • Dome Camera • Straight Tube and other equipped items (optional accessory) •... -
Page 29: Wall Mount
The locking screw plate should be attached to the camera and used in all wall mount applications. There are three types of wall mounts for the Siqura MD20 dome camera: • Mounting with a mini wall mount, as shown in section 6.4.1 •... - Page 30 Dome Installation Tools Needed: • Drill • Screwdriver To mount the dome with the Mini Wall Mount Make a cable entry hole in the wall to recess the cables. For less secure installations, drill a hole in the metal access plate on the bottom of the mount or leave the access plate off entirely.
-
Page 31: Wall Mounting With Gooseneck Tube
Items Needed: • Dome Camera • Gooseneck Tube and other equipped items (optional accessory) • Screws and screw anchors (not supplied) • Indoor tube adaptor for MD20 Tools Needed: • Drill • Screwdriver To mount the dome with the gooseneck tube Make a cable entry hole on the wall to recess the cables. -
Page 32: Wall Box Mounting
6.4.3. Wall box mounting Items Needed: • Dome Camera • Wall Box Mount and other equipped items (optional accessory) • Indoor tube adaptor for MD20 Tools Needed: • Drill • Screwdriver To mount the dome with the gooseneck tube and wall box Fix the wall box to the wall with proper screws and screw anchors (not supplied). -
Page 33: Corner Mount
Figure 6.8 Wall Box Mounting: Wall Box Mount + Gooseneck Tube 6.5. Corner Mount There are two ways to corner mount a Siqura MD20 dome camera: • With a standard or mini mounting plate, as shown in section 6.5.1 • With a thin or wide box as shown in section 6.5.2 6.5.1. -
Page 34: Corner Thin/Wide Box Mounting
Dome Installation To mount the dome camera with the corner standard/mini mounting plate and gooseneck tube/mini wall mount Make a cable entry hole on the wall to recess the cables. Otherwise, cables can be threaded through the cable entry hole on the tube. Fix the Corner standard/mini mounting plate on corner wall with proper screws and screw anchors (not supplied). - Page 35 • Gooseneck Tube and other equipped items (optional accessory) • Corner Thin/Wide Box (optional accessory) • Screws and Screw Anchors for fixing the Corner Thin/Wide Box (not supplied) • Indoor tube adaptor for MD20 Tools Needed: • Drill • Screwdriver To mount the dome with the corner box and gooseneck tube Make a cable entry hole in the wall to recess the cables.
-
Page 36: Pole Thin/Wide Direct Mounting
Dome Installation 6.6. Pole Mount There are two ways to pole mount the Siqura MD20 dome camera: • Using a thin wide direct mount as described in section 6.6.1 • Using a thin wide box mount as described in section 6.6.2 6.6.1. -
Page 37: Pole Thin/Wide Box Mounting
• Dome Camera • Gooseneck Tube and other equipped items (optional accessory) • Pole Thin/Wide Box (optional accessory) • Stainless Steel Straps (optional accessory) • Indoor tube adaptor for MD20 Tools Needed: • Stainless Strap Cutter • Screwdriver To mount the dome camera with the pole box and gooseneck tube Fasten the pole thin/wide box on a pole with equipped stainless straps. - Page 38 Dome Installation Connect the cables to the dome camera. Then attach the dome to the indoor tube adaptor and fix them with the supplied screw. Figure 6.12 Pole Box Mounting: Pole Thin/Wide Box + Gooseneck Tube...
-
Page 39: System Integration
System Integration SYSTEM INTEGRATION The dome camera can be integrated into other suppliers' surveillance systems with the Pelco D protocols. Refer to the following sections for more information. 7.1. Using a Control Keyboard The speed dome camera can be controlled through a Pelco keyboard supplied with the Pelco D protocol. -
Page 41: Appendix A: Camera Accessories
If anything is missing, do not install the dome. Contact your dealer for assistance. Siqura MD20 accessories Security Screw Set (equipped with Vandal Proof Cover) Power Adapter • Input: 100~115VAC/Output: 24VAC 36VA •... -
Page 42: M Ounting A Ccessories
Camera Accessories Mounting Accessories Before installing, make sure you have all the parts listed. If anything is missing, do not install the dome. Contact your dealer for assistance. Indoor tube adaptor For mounting the indoor dome camera onto a gooseneck/straight tube. White;... - Page 43 Camera Accessories T-Bar Ceiling Mount, T-Bar Body Holder and Red Sticker For In-ceiling Installation use. T-Bar Ceiling Mount: Height: 85 mm (3.35 in.); Diameter: 180 mm (7.1 in.); 0.5 kg (1.1 lbs).Red Sticker: 155 +/- 3 mm (6.1 +/- 1.2 in.) Ceiling Panel For ceiling mounting.
-
Page 44: M Ounts And M Ounting B Oxes
Camera Accessories Mounts and Mounting Boxes To secure the indoor tube adaptor to the tube or wall mount, all tube mounts and the mini wall mount are supplied with the following: • Cup washer (1) • 8mm spring washer (1) •... - Page 45 Camera Accessories Swan-neck Mount White, Iron, Height: 250/500 mm (9.8/19.7 in.) ,Diameter: 50 mm (2 in.) 1 kg (2.2 lbs) / 1.8 kg (4 lbs) Straight Tube White, Iron, Height: 250/500 mm (9.8/19.7 in.) ,Diameter: 50 mm (2 in.) 1 kg (2.2 lbs) / 1.8 kg (4 lbs).
- Page 46 Camera Accessories Corner Standard Mounting Plate White, 222×204×117 mm (8.7×8×4.6 in.); 2 kg (4.4 lbs); Supplied with washer-8×4, spring washer×4, M8*16 screw×4, M8 nut×4. Corner Thin Box White/Ivory, 300×164×222 mm (11.8×6.5×8.7 in.); 3 kg (6.7 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4.
- Page 47 Camera Accessories Corner Wide Box White/Ivory; 232×234×210 mm (9.1×9.2×8.3 in.); 2.7 kg (6 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4. Pole Thin Box White/Ivory; 291×136×242 mm (11.5×5.4×9.5 in.); 3.1 kg (6.9 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4.
- Page 48 Camera Accessories Pole Wide Box White/Ivory, 270×166×155 mm (10.6×6.5×6.1 in.); 3.2 kg (7.1 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Wall Box Mounting Ivory, 270(L)×166(W)×95(D) (10.6×6.5×3.7 in.); 2.2 kg (4.84 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4...
- Page 49 Camera Accessories Pole Thin Direct Mounting White/Ivory, 232×136×60 mm (9.1×5.4×2.4 in.); Diameter: 112~140 mm (4.4~5.5 in.); 0.7 kg (1.6 lbs); Supplied with stainless steel straps×4, M8*16 screw×4, washer×4. Pole Wide Direct Mounting White/Ivory, 270×170×60 mm (10.6×6.7×2.4 in.); Diameter: 112~130 mm (4.4~5 in.); 1 kg (2.2 lbs);...
-
Page 51: Appendix B: Technical Specifications
Technical Specifications APPENDIX B: TECHNICAL SPECIFICATIONS Item Siqura MD20 CAMERA CCD Sensor 1/4" EXview CCD Optical Zoom Digital Zoom 1×~ 10× variable NTSC 380k Effective Pixels 440k Horizontal Resolution 470 TVL Scanning System NTSC / PAL Synchronization Internal / Line Lock Video Output 1.0 Vp-p / 75 Ω, BNC... - Page 52 Technical Specifications Item Siqura MD20 Alarm Reaction Preset, Sequence, Auto pan, Cruise GENERAL Environment Indoor Operating Temperature 0°C ~ 40°C (32°F ~ 104°F) Waterproof Standard Dimension 133 x 173 mm (5.2 x 6.8 in) Weight 1.4 kg (3 lbs) Power Source 24VAC 50/60Hz ±...
- Page 54 © Optelecom-NKF B.V. 2008 *%199925410900-00%* Version 1.0 (081212-1) Siq MD20 Installman (MW03SP3)
Need help?
Do you have a question about the MD20 and is the answer not in the manual?
Questions and answers