Subscribe to Our Youtube Channel
Related Manuals for Lionel Halloween Witch Pylon
Summary of Contents for Lionel Halloween Witch Pylon
- Page 1 71-4297-250 3/07 Lionel Lionel Halloween Witch Pylon Halloween Witch Pylon Owner’s Manual Owner’s Manual...
-
Page 2: Table Of Contents
StationSounds ™ , Pullmor ® , ElectroCoupler ™ , Magne-Traction ® , CAB-1 ® Remote Controller, PowerMaster ® , Lionel ZW ® , ZW ® , PowerHouse ® , TMCC ® , Lionelville ™ , Lockon ® , Wireless Tether ™ , LionMaster ® , FatBoy ™ , American Flyer ® , TrainSounds ™ , PowerMax ™... -
Page 3: Wiring Your Pylon With A Conventional Power Supply
The Pylon will operate best at 12-18 volts (AC), and it can be powered through track power with a Lionel Lockon (available separately, 6-62900), or a FasTrack Accessory Power Wire (available separately, 6-12053), OR through an accessory power supply. - Page 4 Wiring your Pylon with a conventional power supply (continued) Mounting holes Mounting holes FasTrack Accessory Power Wire Figure 1. Wiring for conventional operation...
-
Page 5: Installing Your Pylon
Installing your Pylon hoose a flat, level area on your layout for the accessory. Secure this accessory to your layout with four screws (not included) using the holes near the corners of the base. Be sure to wire your accessory before you secure it to your layout—the wire terminals are on the underside of the base. -
Page 6: Attaching The Witch To Your Pylon
Attaching the witch to your Pylon omplete the assembly of your Pylon by attaching the witch and support rod to the structure. Figure 2 illustrates the following procedure. 1. Note that the supporting rod has different shaped ends. Insert the D-shaped coupling bottom end of the support rod onto the D-shaped mounting post on the top of the pylon. -
Page 7: Operating Your Pylon With Trainmaster Command Control
Operating your Pylon with TrainMaster Command Control ou may choose to wire your accessory with an SC-2 Switch and Accessory Controller (available separately, 6-22980) or the Accessory Switch Controller (available separately, 6-14182). Refer to these manuals for additional information. SC-2 wiring and operation Three wires (not included) are needed to connect your Pylon to the SC-2 and a separate accessory transformer. - Page 8 Operating your Pylon with TrainMaster Command Control (continued) Accessory Switch Controller wiring and operation Three wires (not included) are needed to connect your Pylon to the Accessory Switch Controller (ASC) and a separate accessory transformer. Refer to Figure 4. 1. Attach one wire to the transformer Power/A terminal and connect it to the COMM terminal on the ASC.
-
Page 9: Replacing The Lamp In Your Pylon
Replacing the lamp in your Pylon our Pylon is illuminated by one lamp. During the course of normal operations, this lamp may require replacement. Follow these steps to replace the lamp with Lionel part no. 671-4217-300. 1. Lift the support arm out of the tubes at the top of the pylon. Also, remove any screws securing the base to your layout. - Page 10 Replacing the lamp on your Pylon (continued) Base of the Pylon Mounting holes Roof Roof screws screws (recessed) (recessed) Mounting holes Figure 5. Screw locations...
- Page 11 Replacing the lamp on your Pylon (continued) Interior of the building with the roof removed Lionel part no. 671-4217-300 Figure 6. Lamp location...
-
Page 12: Limited Warranty/Lionel Service
Lionel L.L.C. or an authorized Lionel L.L.C. Service Center, together with proof of original purchase will, at the option of Lionel L.L.C., be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the original purchase price will be granted.
Need help?
Do you have a question about the Halloween Witch Pylon and is the answer not in the manual?
Questions and answers