Table of Contents
Advertisement
Viewable Picture Area:
LTC 2914/91: 34 cm (13.4-in) measured diagonally.
LTC 2917/91: 41 cm (16-in) measured diagonally.
LTC 2919/90: 45.7 cm (18-in) measured diagonally.
Linearity:
Horizontal: 7%.
Vertical: 7%.
Horizontal Resolution: 700 TV lines (min).
Video Input:
Composite Video: 0.3 to 1.5 Vp-p, sync negative. Manual
switching from 75 Ω unbalanced to Hi-Z with loop-through
operation via the impedance switch.
Y/C:
Y-signal: 0.7 Vp-p,
C-signal: 0.3 Vp-p. Manual switching from 75 Ω
unbalanced to Hi-Z with loop-through operation via the
impedance switch.
Audio Input: 1 V line level.
Audio Output: Loop-through line level, 1 W speaker.
4.2
Mechanical
Cabinet:
Material: Steel with plastic front.
Finish: Charcoal.
Dimensions:
LTC 2914/91: 356 W x 380 D x 333 H mm (14 x 15 x
13.1 in).
LTC 2917/91: 400 W x 406 D x 363 H mm (15.75 x 16 x
14.3 in).
LTC 2919/90: 441 W x 444 D x 413 H mm (17.4 x 17.5
x 16.25 in).
Weight:
LTC 2914/91: 13.2 kg (29 lb).
LTC 2917/91: 19 kg (41.8 lb).
LTC 2919/90: 21.8 kg (48 lb).
4.3
Environmental
Temperature:
Operating: 0°C to 40°C (32°F to 104°F),
Storage: –10°C to 50°C (14°F to 122°F).
Humidity: 10%–90%, noncondensing.
4.4
Agency Certifications
EMC:
Immunity: EN50130-4.
Emission: EN50081-1 1992, FCC Part 15, Class B.
Product complies with DHHS Rules 21 CFR applicable at the
date of manufacture.
Safety:
CE, LVD Requirement: EN60950 1992.
ETL: ANSI/UL1950.
cETL: CAN/CSA_C22.2, No. 950.
5
TROUBLESHOOTING GUIDE
No Power Indicated: The power plug may be loose or
disconnected.
Resolution: Insert the power plug firmly into the socket.
Power On, No Display: (1) No video signal connected; (2)
Video cable is disconnected.
Resolution: (1) Select and push correct video input button; (2)
Check video cable for proper connection and correct accordingly.
Power On, No Sound: (1) Incorrect cable connection
configuration; (2) Audio cable is disconnected; (3) Volume
output is set too low.
Resolution: (1) Ensure that cable connection configuration is
correct (see Section 2.5); (2) Connect audio cable firmly;
(3) Adjust speaker volume via OSD menu.
Display Jitter: The monitor may be close to a device generating
a strong magnetic field.
Resolution: Move the device away from the monitor until
picture stabilizes.
No Color, Incorrect Color, or Dark Color: The picture control
setting (e.g. Tint, Color, Brightness, or Contrast) may be set
improperly.
Resolution: Reset each picture control setting to the mid-range
level, or restore the factory DEFAULT setting in the OSD
menu.
Unnatural Color, Irregular Color, or Distorted Picture: The
monitor may be close to a speaker, magnet, or any other device
generating a strong magnetic field.
Resolution: Move the device away from the monitor and
discontinue power to the monitor. Wait at least 3 minutes, then
restore power to the monitor.
Picture Overexposure: The video input signal is not terminated.
Resolution: Ensure that the impedance switch on the rear panel
for that channel is set to the 75 Ω position, which properly
terminates the signal.
A Blank Display in Sequence Mode: Upon power-up, the
monitor memorizes the system configuration (i.e., the number or
video inputs which are connected). If a video input is added
after power-up, that signal will NOT be displayed in sequence
mode.
Resolution: Turn off the monitor for a few seconds, then power
up again. The additional signal should now be included in the
sequence mode.
11
Hide quick links:
Advertisement
Table of Contents
