Table of Contents
Advertisement
Power Clear Snowthrower
Model No. 38587—Serial No. 311000001 and Up
Model No. 38593—Serial No. 311000001 and Up
Introduction
This machine is intended to be used by residential
homeowners or professional, hired operators. It
is designed primarily for removing snow from
paved surfaces, such as driveways and sidewalks,
and other surfaces for traffic on residential or
commercial properties. It is not designed for
removing materials other than snow, nor is it
designed for clearing off gravel surfaces.
Read this information carefully to learn how to operate
and maintain your machine properly and to avoid injury
and machine damage. You are responsible for operating
the machine properly and safely.
You may contact Toro directly at www.Toro.com for
machine and accessory information, help finding a
dealer, or to register your machine.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your machine ready. Figure 1
identifies the location of the model and serial numbers
on the machine. Write the numbers in the space
provided.
Figure 1
1. Model and serial number location
Model No.
Serial No.
This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious
injury or death if you do not follow the recommended
precautions.
© 2010—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
1. Safety alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects,
This spark ignition system complies with Canadian
ICES-002.
The enclosed Engine Owner's Manual is supplied
for information regarding the US Environmental
Protection Agency (EPA) and the California
Emission Control Regulation of emission systems,
maintenance, and warranty. Replacements may be
ordered through the engine manufacturer.
Safety
This machine meets or exceeds the B71.3
specifications of the American National Standards
Institute in effect at the time of production.
Read and understand the contents of this manual
before you start the engine.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
Improperly using or maintaining this machine
could result in injury or death. To reduce this
Register at www.Toro.com.
Form No. 3365-632 Rev A
Operator's Manual
Figure 2
WARNING
CALIFORNIA
Proposition 65 Warning
or other reproductive harm.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro 38587
Summary of Contents for Toro 38587
- Page 1 Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model This spark ignition system complies with Canadian and serial numbers of your machine ready. Figure 1 ICES-002.
- Page 2 potential, comply with the following safety – If fuel is spilled on clothing, change clothing instructions. immediately. • Use extension cords and receptacles as specified This machine is capable of amputating hands and by the manufacturer for all machines with electric feet and of throwing objects.
-
Page 3: Clearing A Clogged Discharge Chute
The following list contains safety information specific • Disengage power to the rotor blades when the to Toro products or other safety information that you machine is transported or not in use. must know. • Never operate the machine without good visibility •... -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 94-2577 1. To engage the rotor blades, hold the control bar against the handle. 2. To disengage the rotor blades, release the control bar. 114-1707 Order part no. -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Unfold the handle. Discharge chute Chute handle Phillips head screws Install the discharge chute. Washers Locknuts Unfolding the Handle No Parts Required Figure 5 Procedure... -
Page 6: Installing The Discharge Chute
Installing the Discharge Chute Adjusting the Control Cable Parts needed for this procedure: No Parts Required Discharge chute Procedure Chute handle Refer to Adjusting the Control Cable in Maintenance. Phillips head screws Washers Product Overview Locknuts Procedure Install the discharge chute as shown (Figure 7). Figure 8 1. -
Page 7: Mixing Gasoline And Oil
Fill the fuel tank with fresh fuel (Figure 10). Mixing Gasoline and Oil This machine uses a 50:1 gasoline-to-oil mixture. Use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added) or an equivalent high-grade, NMMA TCW 3-certified 2-cycle oil. Important: Do not use E85 or E20 fuel. Alternative... -
Page 8: Starting The Engine
Starting the Engine 1. Turn the ignition key clockwise to the On position (Figure 11). Figure 14 Figure 11 Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole. 2. Move the choke lever to the right (Figure 12 and Important: Do not use the primer or the Figure 13). -
Page 9: Disengaging The Rotor Blades
WARNING The electrical cord can become damaged, causing a shock or fire. Thoroughly inspect the electrical cord before plugging it into a power source. If the cord is damaged, do not use it to start the machine. Replace or repair the damaged cord immediately. -
Page 10: Adjusting The Discharge Chute
Adjusting the Discharge Chute when trying to operate frozen controls. If you have difficulty operating any control or part, start the To adjust the discharge chute, move the chute handle engine and let it run for a few minutes. and the chute deflector handle as shown (Figure 20). Operating Tips WARNING The rotor blades can throw stones, toys, and other... -
Page 11: Recommended Maintenance Schedule(S)
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the control cable and adjust it if necessary. After the first hour • Check for loose fasteners and tighten them if necessary. •... -
Page 12: Servicing The Spark Plug
Inspecting the Rotor Blades 2. Move the Z-fitting to a higher or lower hole on the adjuster link as needed to obtain the 1/16-inch to Service Interval: Yearly—Inspect the rotor blades and 1/8-inch (2 mm to 3 mm) gap between the control have an Authorized Service Dealer bar and the handle (Figure 22). -
Page 13: Replacing The Drive Belt
12. Install the spark plug and tighten it securely. 13. Connect the wire to the spark plug. 14. Remove the fuel tank cap. 15. Install the shroud with the screws you removed in step 4. Note: Ensure that the upper and lower shrouds fit together in the side grooves. -
Page 14: Storing The Machine
Storage 4. Remove the rotor pulley and the drive belt (Figure 27). 5. Install the new drive belt, routing it as shown in Storing the Machine Figure 28. WARNING • Gasoline fumes are highly flammable, explosive, and dangerous if inhaled. If you store the machine in an area with an open flame, the gasoline fumes may ignite and cause an explosion. - Page 15 Notes:...
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.