Toro 38535 Operator's Manual
Hide thumbs Also See for 38535:

Advertisement

CCR™ 2450 GTS® Snowthrower
Model No. 38535—Serial No. 270000001 and Up
Introduction
Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.
You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a dealer,
or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. Figure 1 identifies the
location of the model and serial numbers on the product.
Write the numbers in the space provided.
Figure 1
1. Model and serial number location
Model No.
Serial No.
This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (Figure 2),
which signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.
Figure 2
1. Safety alert symbol
This manual uses 2 other words to highlight information.
Important calls attention to special mechanical information
and Note emphasizes general information worthy of special
attention.
© 2006—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Safety
This snowthrower meets or exceeds the ISO standard
8437 in effect at the time of production.
Read and understand the contents of this manual
before the engine is ever started.
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
Improperly using or maintaining this snowthrower
could result in injury or death. To reduce this potential,
comply with the following safety instructions.
Training
Read the operating and service instruction manual
carefully. Be thoroughly familiar with the controls and
the proper use of the equipment. Know how to stop
the unit and disengage the controls quickly.
Never allow children to operate the equipment. Never
allow adults to operate the equipment without proper
instruction.
Keep the area of operation clear of all persons,
particularly small children, and pets.
Exercise caution to avoid slipping or falling, especially
when operating in reverse.
Preparation
Thoroughly inspect the area where the equipment is to
be used and remove all doormats, sleds, boards, wires,
and other foreign objects.
Disengage all clutches and shift into neutral before
starting the engine. Do not operate the equipment
without wearing adequate winter garments.
Wear footwear which will improve footing on slippery
surfaces.
Handle fuel with care; it is highly flammable.
– Use an approved fuel container.
– Never add fuel to a running or hot engine.
– Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
– Replace gasoline caps securely and wipe up spilled
fuel.
Register at www.Toro.com.
Form No. 3355-468 Rev A
Operator's Manual
Original Instructions (EN)
Printed in the USA
All Rights Reserved

Advertisement

Table of Contents
loading

Summary of Contents for Toro 38535

  • Page 1 Authorized Service Improperly using or maintaining this snowthrower Dealer or Toro Customer Service and have the model and could result in injury or death. To reduce this potential, serial numbers of your product ready. Figure 1 identifies the comply with the following safety instructions.
  • Page 2: Maintenance And Storage

    The following list contains safety information specific to • Do not run the engine indoors, except when starting Toro products or other safety information that you must it and for moving the snow thrower in or out of the know.
  • Page 3: Safety And Instructional Decals

    Remove the key from the ignition switch before storing or lost, repair or replace it before beginning operation. the snowthrower. Also, tighten any loose fasteners. • Purchase only genuine Toro replacement parts and • Do not smoke while handling gasoline. accessories. •...
  • Page 4 105-1979 Order Part No. 108-7342 1. Choke 2. Use unleaded gasoline; 50:1 gas:oil mixture. 3. To start the engine, move the choke to the right, push the primer twice, turn the key, and push the choke left after it starts. 4.
  • Page 5: Loose Parts

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Step Qty. Description Wheels Long spacer Install the wheels. Short spacer Pushnuts – No parts required Install the handle. Discharge chute Chute handle Phillips head screws Install the discharge chute.
  • Page 6: Table Of Contents

    6. Tighten the knobs until they are snug. 7. Adjust the control cable. Refer to Adjusting the Control Cable. 3. Installing the Discharge Chute Install the discharge chute as shown (Figure 9). Figure 5 3. Loosely install the handle bolts, curved washers, and knobs (Figure 6).
  • Page 7: Figure

    Mixing the Gasoline and Oil This snowthrower uses a 50:1 gasoline-to-oil mixture. Use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added) or an equivalent high-grade, NMMA TCW-certified two-cycle oil. Important: To prevent engine damage, do not use automotive oil (such as SAE 30 or 10W30) or fuel mixed at the wrong gasoline-to-oil ratio.
  • Page 8: Figure

    4. Shake the container to mix the gasoline and oil thoroughly. 5. Slowly remove the cap and add the remaining amount of gasoline. Note: Do not mix gasoline and oil in the fuel tank. Oil at room temperature mixes easier and more thoroughly Figure 16 than cold oil.
  • Page 9: Figure

    Stopping the Rotor Blades • Remove the snow as soon as possible after it falls. • To self-propel, raise the handle and tilt the snowthrower To stop the rotor blades, release the control bar (Figure 20). slightly forward, lifting the wheels off the ground. The more you tilt the handle forward, the faster the snowthrower self-propels.
  • Page 10: Figure

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the control cable both initially and after the rst hour of operation; adjust it After the rst operating if necessary.
  • Page 11: Figure

    1. Add a fuel stabilizer/conditioner to the fuel in the fuel blades and the scraper (Figure 25) tank as directed. Note: If you use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added), you do not need to add a fuel stabilizer/conditioner.
  • Page 12 Folding the Handle 1. Loosen the knobs and pull out the handle bolts. 2. Fold the upper handle forward (Figure 26). Figure 26...
  • Page 15 357 22 434131 Spypros Stavrinides Limited Surge Systems India Limited India 91 1 292299901 T-Markt Logistics Ltd Hungary 36 26 525 500 61 3 9580 7355 Toro Australia Australia Toro Europe BVBA Belgium 32 14 562 960 374-0102 Rev A...
  • Page 16 Instructions for Obtaining Warranty Service The Toro® Company and its afliate, Toro Warranty Company, If you think that your Toro Product contains a defect in materials pursuant to an agreement between them, jointly promises to the or workmanship, follow this procedure: original purchaser* to repair any Toro Product used for normal 1.

This manual is also suitable for:

Ccr 2450 gts

Table of Contents