Adjusting Subwoofer Level/Bass Level; Treble Level/Fader (Between Front And Rear); Black Out In Multeq Mode; Adjusting Sound Setting In Manual Mode - Alpine CDA-137EBT Owner's Manual

Adjusting Subwoofer Level/Bass Level/

Treble Level/Fader (Between Front and
Rear)/Balance (Between Left and Right)/

Black Out in MultEQ mode

You can change these settings to create your own preference in MultEQ
(Curve 1 or Curve 2) mode.
1
Press AUDIO repeatedly to select the MultEQ adjustment
item.
*1 *2
SUBWOOFER d BASS d TREBLE
*4
BLACK OUT d DEFEAT d VOLUME d SUBWOOFER
*1 When the SUBWOOFER mode is set to OFF, its level cannot be
adjusted.
This function is inoperable when MultEQ is set to OFF.
*2
If you set the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) switch
*3
of the IMPRINT audio processor (PXA-H100) to 2.2ch (3WAY), you
cannot adjust the FADER mode. For details, refer to the Owner's
Manual of PXA-H100.
When BLACK OUT mode is turned ON, all display indications on
*4
this unit will turn off to reduce power consumption. This additional
power enhances the sound quality. If any button on the unit is
pressed during the Blackout Mode, the function is displayed for 5
seconds before returning to Blackout mode.
Note
• If no operation is performed for 5 seconds after selecting the
SUBWOOFER, BASS, TREBLE, FADER, BALANCE, BLACK OUT or
DEFEAT mode the unit automatically returns to normal mode.
2
Turn the Rotary encoder to change the setting as below.
Subwoofer level
Bass level
Treble level
Balance
Fader
Black Out
Defeat
Volume
Note
• Depending on the connected devices, some functions and display
indications do not work.
34
-EN
*2 *3
d BALANCE d FADER
d
0 ~ 15
-7 ~ +7
-7 ~ +7
-15(L) ~ 15(R)
-15(R) ~ 15(F)
ON/OFF
ON/OFF
0 ~ 35

Adjusting Sound Setting in Manual Mode

You can change these sound settings to create your own preference when
the MultEQ mode is set to Mult EQ OFF (Manual Mode).
Use steps 1 to 4 to select one of the Sound menu modes to
modify. See the applicable section below for details about the
selected item.
1
Press and hold SOUND SETUP for at Least 2 seconds to
activate the Sound menu selection mode.
2
Turn the Rotary encoder to select the desired item, and
then press s/ENTER.
MultEQ Mode  Subwoofer  SUBW. System
*1
 SUBW. Channel  Factory's EQ  TW Setup
 Media Xpander  MX Level
*4
 Sound Field  MultEQ Mode
(e.g. Select Subwoofer)
These functions are inoperable when Subwoofer is set to OFF.
*1
This function can be operable only when PXA-H100 (sold
*2
separately) is connected and 2.2ch (3WAY) mode is set. For details,
refer to the Owner's Manual of PXA-H100.
This function is inoperable when Media Xpander is set to OFF.
*3
In step 2, three sound adjustment items (Parametric EQ/ Graphic
*4
EQ, T.Correction, X-Over) can be selected in Sound Field
Adjustment mode, turn the Rotary encoder
item, and then press
s/ENTER
3
Turn the Rotary encoder to change the setting, and then
press s/ENTER.
(e.g. Select Subwoofer ON or Subwoofer OFF)
4
Press and hold for at least 2 seconds to return to normal
c
mode.
Note
• Media Xpander, Factory's EQ, Parametric EQ/Graphic EQ, EQ Mode
and MX Level Adjustment are inoperable when DEFEAT is set to ON.
Pressing c returns to the previous Sound menu mode.
•
• If no operation is performed for 60 seconds, Sound menu mode is
cancelled.

Turning Subwoofer ON/OFF

When the subwoofer is on, you can adjust the subwoofer output level.
Setting item: Subwoofer
e
Setting contents:
ON (Initial setting) / OFF
ON:
The subwoofer signal is output from the Subwoofer RCA Connectors
(refer to "Connections" on page 50)
OFF:
No subwoofer signal is output from the Subwoofer RCA Connectors
(refer to "Connections" on page 50).

Setting the Subwoofer System

When the subwoofer is on, you can select either System 1 or System 2 for
the desired subwoofer effect.
Setting item: SUBW. System
e
*1
 SUBW. Phase
*2
 Filter Type
*3
 EQ Mode  TCR Parameter
to select the desired
to continue to step 3.
*1