Table of Contents
Advertisement
Electrical Parts List
Product safety should be considered when a component replacement is made in any area of a projector.
Key No.
Part No.
Components indicated by a ! mark in this parts list and the circuit diagram show components whose value have
special significance to product safety. It is particularly recommended that only parts specified on the following parts
list be used for components replacement pointed out by the mark.
● Read Description in the parts list
Read description in the Capacitor and Resistor as follows:
CAPACITOR
CERAMIC 100P K 50V
RESISTOR
Description
Tolerance Symbols:
Less than 10pF
A : Not specified B : ±0.1pF
D : ±0.5pF
G : ±2pF
R : ±0.25 -0pF
More than 10pF
A : Not specified B : ±0.1%
D : ±0.5%
H : ±3%
L : ±15%
P : +100-0%
U : +75-10%
X : +40-20%
Rated value: P=pico farad, U=micro farad
Material:
CERAMIC........... Ceramic
MT-PAPER......... Metallized Paper
POLYESTER...... Polyester
MT-POLYEST.....Metallized Polyester
POLYPRO.......... Polypropylene
MT-POLYPRO....Metallized Polypropylene
COMPO FILM.....Composite film
MT-COMPO........Metallized Composite
STYRENE...........Styrene
TA-SOLID........... Tantalum Oxide Solid Electrolytic
AL-SOLID........... Aluminium Solid Electrolytic
ELECT................ Aluminum Foil Electrolytic
NP-ELECT..........Non-polarised Electrolytic
OS-SOLID.......... Aluminium Solid with Organic Semiconductive Electrolytic
POS-SOLID........ Polymerized Organic Semiconductive
DL-ELECT.......... Double Layered Electrolytic
PPS-FILM...........Polyphenylene Sulfide Film
MT-PPS-FILM.....Metalized Polyphenylene Sulfide Film
MT-PEN-FILM.....Metalized Polyethylenenaphthalate Film
CAPACITOR.......Other
CARBON
4.7K
J
A
1/4W
Performance Symbols:
A: General B: Non flammable Z: Low noise
Other: Temperature coefficient
Tolerance Symbols:
A: ±0.05% B: ±0.1% C: ±0.25% D: ±0.5%
F: ±1%
M: ±20%
Rated value, ohms:
K: 1,000, M: 1,000,000
Material:
CARBON........... Carbon
MT-FILM............ Metal Film
OXIDE-MT......... Oxide Metal Film
SOLID................ Composition
MT-GLAZE......... Metal Glaze
WIRE WOUND... Wire Wound
CERAMIC RES.. Ceramic
FUSIBLE RES.... Fusible
RESISTOR ........ Other
Key No.
Part No.
Rated Voltage
C : ±0.25pF
F : ±1PF
E : +0 -1pF
H : +0.1 -0pF
L : +0 -0.1pF
S : +0-0.25pF
C : ±0.25%
F : ±1%
G : ±2%
J : ±5%
K : ±10%
M : ±20%
N : ±30%
Q : +30-10%
T : +50-10%
V : +20-10%
W : +100-10%
Y : +150-10% Z : +80-20%
Rated Wattage
T: ±10ppm/°C
U: ±25ppm/°C
D: ±100ppm/°C
E: ±200ppm/°C
G: ±350ppm/°C
H: ±1000ppm/°C±10% W: ±1200ppm/°C±10%
Y: ±1400ppm/°C±10% J: ±2000ppm/°C±10% K: ±2400ppm/°C±10%
L: ±2700ppm/°C±10% M: ±3000ppm/°C±10% N: ±3300ppm/°C±10%
P: ±3600ppm/°C±10% Q: ±3900ppm/°C±10% R: ±4200ppm/°C±10%
S: ±4300ppm/°C±10% V: ±4500ppm/°C±10% X: ±8000ppm/°C±10%
G: ±2%
J: ±5%
K: ±10%
P: +5-15% Z: 0 ohm
-107-
-107-
Description
C: ±50ppm/°C
F: ±250ppm/°C
MP7-EF6000
Advertisement
Table of Contents
