Canon PIXMA MX700 series Quick Start Manual page 159

2-A Setting up for use over LAN
This section describes how to set up the machine to be used over wired LAN, when the machine has
not been connected to the network. This setup procedure requires settings to be performed on the
machine and the computer.
1
On the Setup Method screen, select Set up
the printer and the computer for network
use, then click Next.
W
Note
If you select Use the printer via USB, the machine is
set up to be used with USB connection.
(,; :..., ....
" : J l " ' > ~
.... <••• '';X';O..
,j'J< •
...-~~¥....
I
~
•••
i'2:::F:-'';;::::::::;::;;;:';;:''':::;~'
I
G"V~Y'~
~~sur~ll\aIIlrlepr,,,,,,,~(~~[,ItI<'.;('-np,A~ ''''':''''0,'''1
ll".f'l)f1rl'l91
Printer Connection
I
,
.
;
l
t
~IW'
,
i
I
r
m ...
Irltorm""_
2
When the Printer Connection screen
appears, connect the machine to the
computer with a USB cable, then turn on the
machine.
When the machine is turned on, the Power lamp
lights up green. When the computer detects the
machine, the next screen will appear automatically.
When using Windows 2000:
When you connect the machine to the computer
with a USB cable, a message asking for your
confirmation to restart your computer is displayed.
Click Yes. Then when an error message is
displayed, click OK to proceed with the installation.
W
Note
• To set up the machine that is not yet connected to a
LAN, connect the machine and the computer with a
USB cable.
• If you cannot go to the next procedure after 3
minutes, refer to "Cannot Install the MP Drivers" in
"Troubleshooting" in the User's Guide on-screen
manual.
3
When the Setup Preparations dialog box
appears, confirm that preparation is
complete, then click Next.
W
Note
If the machine's network settings are already
configured, the Setup Environment Confirmation
dialog box appears asking for your confirmation to use
the machine with the current settings. You can
proceed with the setup using the current network
settings. To do so, click Use it as is. To reconfigure the
network settings, click Reconfigure.
7
2-A Setting up for use over LAN
This section describes how to set up the machine to be used over wired LAN, when the machine has
not been connected to the network. This setup procedure requires settings to be performed on the
machine and the computer.
1
On the Setup Method screen, select Set up
the printer and the computer for network
use, then click Next.
W
Note
If you select Use the printer via USB, the machine is
set up to be used with USB connection.
(,; :..., ....
" : J l " ' > ~
.... <••• '';X';O..
,j'J< •
...-~~¥....
I
~
•••
i'2:::F:-'';;::::::::;::;;;:';;:''':::;~'
I
G"V~Y'~
~~sur~ll\aIIlrlepr,,,,,,,~(~~[,ItI<'.;('-np,A~ ''''':''''0,'''1
ll".f'l)f1rl'l91
Printer Connection
I
,
.
;
l
t
~IW'
,
i
I
r
m ...
Irltorm""_
2
When the Printer Connection screen
appears, connect the machine to the
computer with a USB cable, then turn on the
machine.
When the machine is turned on, the Power lamp
lights up green. When the computer detects the
machine, the next screen will appear automatically.
When using Windows 2000:
When you connect the machine to the computer
with a USB cable, a message asking for your
confirmation to restart your computer is displayed.
Click Yes. Then when an error message is
displayed, click OK to proceed with the installation.
W
Note
• To set up the machine that is not yet connected to a
LAN, connect the machine and the computer with a
USB cable.
• If you cannot go to the next procedure after 3
minutes, refer to "Cannot Install the MP Drivers" in
"Troubleshooting" in the User's Guide on-screen
manual.
3
When the Setup Preparations dialog box
appears, confirm that preparation is
complete, then click Next.
W
Note
If the machine's network settings are already
configured, the Setup Environment Confirmation
dialog box appears asking for your confirmation to use
the machine with the current settings. You can
proceed with the setup using the current network
settings. To do so, click Use it as is. To reconfigure the
network settings, click Reconfigure.
7