Canon PIXMA MX700 series Quick Start Manual page 106

Message
Action
'There is no photo data."
•
There are no image data saved on the memory card that can be read by this
machine.
• The machine may not recognize the file if the file name or the folder path
contains certain characters. Use only alphanumeric characters.
•
Photo data edited or processed on a computer must be printed from the
computer.
"The waste ink absorber is almost full.
The machine has a built-in ink absorber to hold the ink used during Print Head
Press [OK] to continue but early Cleaning, for example.
replacement recommended. <See
This error message indicates that the ink absorber is nearly full.
manual>"
Press the OK button to cancel the error so you can continue printing.
However, because printing is disabled once the ink absorber becomes
completely full and until the ink absorber is replaced, you are recommended to
contact your Canon service representative as early as possible. (You will need
to replace a particular part of the machine.)
"Incompatible device detected.
A communication time out occurs if an operation takes too long or if it takes too
Remove the device." much time to send data. This may cancel printing. In such cases, disconnect
and reconnect the USB cable.
When printing from a PictBridge compliant device, depending on the model or
brand of your device, you may have to select a PictBridge compliant print mode
on the device before connecting it to the machine. You may also have to turn on
your device or select Play mode manually after connecting the device to the
machine. Perform necessary operations before connecting your device referring
to its instruction manual.
If the error is still not resolved, check if you can print another photograph.
"An unsupported USB hub is If a PictBridge compliant device is connected via a USB hub, remove the hub
connected. Remove the hub." and connect it directly to the machine.
"**** Turn off the machine, and unplug the power cord of the machine from the power
Error code"
supply. After a while, plug the power cord of the machine back in, and then turn
on the machine. If the same error occurs, contact your Canon service
representative.
"Scanner is not operating correctly." Turn off the machine, and unplug the power cord of the machine from the power
supply. After a while, plug the power cord of the machine back in, and then turn
on the machine. If the same error occurs, contact your Canon service
representative.
"The card is currently write-enabled. The Card Slot is set to USB enabled or LAN enabled.
Remove card and set to read-only
You cannot print in this mode. After writing on the memory card, set to Read-
mode before performing operation."
only mode again.
"Document in ADF. Redo operation The document is jammed in the ADF. Remove the document page jammed in
after checking document in ADF and the ADF, then press the OK button. When the error is cleared, redo the
pressing [OK]." operation. See "Document Jams" on page 116.
"Document size is too long. Redo The document is too long or is jammed in the ADF. Remove the document page
operation after checking document on jammed in the ADF, then press the OK button. When the error is cleared, make
ADF and pressing [OK]." sure that the document you are loading meets the machine's requirements
before redoing the operation. See "Original Document Requirements" on page 6
and "Document Jams" on page 116.
"Auto redia'" The machine is waiting to redial the recipient's number because the line was
busy or the recipient did not answer when you tried to send a document. Wait for
the machine to automatically redial the number. If you want to cancel automatic
redialing, wait until the machine starts dialing the number, press the Stop/Reset
button, then follow the instructions on the LCD. You can also delete the
document from memory. See "Document Stored in Memory" on page 73.
"Hang up the phone." The handset is not placed in the handset cradle correctly. Replace the handset
correctly.
"Try again in black & white." The recipient's fax machine is not color-compatible. Press the Black button to
resend the faxes. Alternatively, you can set Color TX to Send in black & white.
"Failed to connect." The telephone line cable with a modular plug is not plugged in properly, or Dial
tone detect is set to ON. Make sure that the cable is plugged in properly, and
resend the fax after a while. If you still cannot send the fax, set Dial tone detect
to OFF
102 Troubleshooting
Message
Action
'There is no photo data."
•
There are no image data saved on the memory card that can be read by this
machine.
• The machine may not recognize the file if the file name or the folder path
contains certain characters. Use only alphanumeric characters.
•
Photo data edited or processed on a computer must be printed from the
computer.
"The waste ink absorber is almost full.
The machine has a built-in ink absorber to hold the ink used during Print Head
Press [OK] to continue but early Cleaning, for example.
replacement recommended. <See
This error message indicates that the ink absorber is nearly full.
manual>"
Press the OK button to cancel the error so you can continue printing.
However, because printing is disabled once the ink absorber becomes
completely full and until the ink absorber is replaced, you are recommended to
contact your Canon service representative as early as possible. (You will need
to replace a particular part of the machine.)
"Incompatible device detected.
A communication time out occurs if an operation takes too long or if it takes too
Remove the device." much time to send data. This may cancel printing. In such cases, disconnect
and reconnect the USB cable.
When printing from a PictBridge compliant device, depending on the model or
brand of your device, you may have to select a PictBridge compliant print mode
on the device before connecting it to the machine. You may also have to turn on
your device or select Play mode manually after connecting the device to the
machine. Perform necessary operations before connecting your device referring
to its instruction manual.
If the error is still not resolved, check if you can print another photograph.
"An unsupported USB hub is If a PictBridge compliant device is connected via a USB hub, remove the hub
connected. Remove the hub." and connect it directly to the machine.
"**** Turn off the machine, and unplug the power cord of the machine from the power
Error code"
supply. After a while, plug the power cord of the machine back in, and then turn
on the machine. If the same error occurs, contact your Canon service
representative.
"Scanner is not operating correctly." Turn off the machine, and unplug the power cord of the machine from the power
supply. After a while, plug the power cord of the machine back in, and then turn
on the machine. If the same error occurs, contact your Canon service
representative.
"The card is currently write-enabled. The Card Slot is set to USB enabled or LAN enabled.
Remove card and set to read-only
You cannot print in this mode. After writing on the memory card, set to Read-
mode before performing operation."
only mode again.
"Document in ADF. Redo operation The document is jammed in the ADF. Remove the document page jammed in
after checking document in ADF and the ADF, then press the OK button. When the error is cleared, redo the
pressing [OK]." operation. See "Document Jams" on page 116.
"Document size is too long. Redo The document is too long or is jammed in the ADF. Remove the document page
operation after checking document on jammed in the ADF, then press the OK button. When the error is cleared, make
ADF and pressing [OK]." sure that the document you are loading meets the machine's requirements
before redoing the operation. See "Original Document Requirements" on page 6
and "Document Jams" on page 116.
"Auto redia'" The machine is waiting to redial the recipient's number because the line was
busy or the recipient did not answer when you tried to send a document. Wait for
the machine to automatically redial the number. If you want to cancel automatic
redialing, wait until the machine starts dialing the number, press the Stop/Reset
button, then follow the instructions on the LCD. You can also delete the
document from memory. See "Document Stored in Memory" on page 73.
"Hang up the phone." The handset is not placed in the handset cradle correctly. Replace the handset
correctly.
"Try again in black & white." The recipient's fax machine is not color-compatible. Press the Black button to
resend the faxes. Alternatively, you can set Color TX to Send in black & white.
"Failed to connect." The telephone line cable with a modular plug is not plugged in properly, or Dial
tone detect is set to ON. Make sure that the cable is plugged in properly, and
resend the fax after a while. If you still cannot send the fax, set Dial tone detect
to OFF
102 Troubleshooting