Operating Jvc's Audio/Video Components; Operating Audio Components - JVC RX-6510VBK Instructions Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.

Operating Audio Components

IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK (SYNCHRO) jacks (see page 26) in addition to the
connections using cables with RCA pin plugs (see pages 5 and 6).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel, the remote control will
not operate that source. To operate a source with the remote
control, the source must be selected using source selecting buttons
on the remote control.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 12.)
• Refer also to the manuals supplied with your components.
CATV/DBS
POWER
DVD
TV SOUND
BASS
SURROUND
ON/OFF
BASS BOOST EFFECT
SOUND
MUTING
RETURN
CATV/DBS
CONTROL CONTROL
TV/VIDEO
TUNING
REC
PAUSE
RM-SRX6510J
A/V CONTROL RECEIVER
* When you press one of the following buttons, the remote
control operation mode appears on the display window for
about 10 seconds.
Buttons on the Remote Control
FM/AM
CD
TAPE/CDR
DVD
TV SOUND
VCR
CATV/DBS CONTROL
CONTROL
SOUND
27
VCR TV AUDIO
POWER POWER POWER
CD
FM/AM
VCR TAPE/CDR
TREBLE
DSP ANALOG/DIGITAL SLEEP
MODE INPUT
– CENTER +
1 2 3
MENU
TEST – REAR • L +
4 5 6
ENTER
– REAR • R +
7/P 8 9
– SUB WOOFER +
0
10 +10
FM MODE 100 +
CH TV VOL VOLUME
PLAY
/REW FF/
PAUSE
STOP CONTROL
Ex.: When you
press CD button
Remote Control Operation Mode
TUNER
CD
TAPE
DVD
TV
VCR
DBS
Current setting or VCR or TAPE
or CDDSC
SOUND
Tuner
You can always perform the following operations:
FM/AM:
Alternates between FM and AM.
After pressing FM/AM, you can perform the following operations:
1 – 10, +10:
Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
TUNING +/–: Tunes into stations.
FM MODE:
Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations:
SURROUND ON/OFF: Turns on or off the Surround modes –
Dolby Pro Logic, Dolby Digital, and
DTS Digital Surround.
DSP MODE:
Selects the DSP modes.
After pressing SOUND, you can perform the following operations:
SUBWOOFER +/–: Adjusts the subwoofer output level.
CENTER +/–: Adjusts the center speaker output level.
REAR•L +/–:
Adjusts the left rear speaker output level.
REAR•R +/–: Adjusts the right rear speaker output level.
EFFECT:
Selects the effect level.
TEST:
Turns on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the 10 keys; otherwise,
the 10 keys cannot be used for operating your target source.
CD player
After pressing CD, you can perform the following operations on the
CD player:
PLAY3:
Starts playing.
4 4 : 4
4 4
Returns to the beginning of the current (or
previous) track.
¢ : ¢ ¢
¢ ¢
Skips to the beginning of the next track.
STOP7:
Stops playing.
PAUSE8: Pauses playing. To release it, press PLAY3.
1 – 10, +10:
Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.