Operating Jvc's Audio/Video Components - JVC RX-6100VBK Instructions Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.
IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 26) in addition to the
connections using cables with RCA pin plugs (see page 5).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel to choose a source, the
remote control will not operate that source. To operate a source with
the remote control, the source must be selected using source
selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 11.)
• Refer also to the manuals supplied with your components.
CATV/ SAT TV
DVD TV SOUND/ DBS
CD ANALOG/DIGITAL
TAPE/MD
REC PAUSE
SURROUND
SURROUND
CATV CH
MODE
SUBWOOFER
1 2
REAR•L
5
6
EFFECT TEST
0
9
TV/ VIDEO
TV CH
MUTING
RM-SRX6500J REMOTE CONTROL
Tuner
After pressing FM/AM, you can perform the following operations:
FM/AM:
Alternates between FM and AM.
1 – 10, +10:
Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
POWER
VCR AUDIO
VCR SLEEP
PHONO
FM/AM
3
8
CATV
CONTROL
7
SOUND
VCR CH
CD - DISC
CNTR
3 4
REAR•R
7 8
/P
MENU
ENTER
+10
10
RETURN 100+
TV VOL VOLUME
Sound control section (Amplifier)
You can always perform the following operations:
SURROUND:
Turns on or off the Surround modes —
Dolby Pro Logic, Dolby Digital, and DTS
Digital Surround.
SURROUND MODE:
Selects the DSP modes.
After pressing SOUND, you can perform the following operations:
SUBWOOFER –/+: Adjusts the subwoofer output level.
CNTR –/+:
Adjusts the center speaker output level.
REAR•L –/+:
Adjusts the left rear speaker output level.
REAR•R –/+: Adjusts the right rear speaker output level.
EFFECT:
Selects the effect level.
TEST:
Turns on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
Turntable
After pressing PHONO, you can perform the following operations
on a turntable:
3:
Starts playing.
7:
Stops operations.
CD player
After pressing CD, you can perform the following operations on the
CD player:
3 3 3 3 3 :
Starts playing.
4 4
4 4 : 4
Returns to the beginning of the current (or
previous) track.
¢ ¢ ¢ ¢ ¢ :
Skips to the beginning of the next track.
7 7 7 7 7 :
Stops playing.
8 8 8 8 8 : Pauses playing. To release it, press 3 3 3 3 3 .
1 – 10, +10:
Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
29