JVC RX-6100VBK Instructions Manual page 34

To change the transmittable signals for
operating another manufacturer's VCR
1. Press and hold VCR POWER.
2. Press VCR.
3. Enter manufacturer's code (two digits) using
buttons 1–9, and 0.
See the list below to find the code.
Examples: For a PANASONIC product, press 0, then 7.
For a MITSUBISHI product, press 1, then 3.
4. Release VCR POWER.
Following button can be used for operating the VCR:
VCR POWER: Turns on and off the VCR.
After pressing VCR, you can perform the
following operations on the VCR:
VCR CH +/–:
Changes the TV channels on the VCR.
3:
Starts playback.
1:
Rewinds a video tape.
¡:
Fast winds a video tape.
7:
Stops operation.
8: Pauses. To resume playing, press 3.
REC PAUSE:
Pauses recording temporarily.
Note:
Refer to the manual supplied with your VCR.
5. Try to operate your VCR by pressing VCR
POWER.
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of VCR,
try each one until the correct one is entered.
Manufacturer Codes
Emerson 11
Fisher 29
Funai 10, 14, 15, 16
GoldStar 12
Hitachi 04
JVC 01, 02, 03
Mitsubishi 13
NEC 25
Panasonic 07, 17
Manufacturers' codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
32
Manufacturer Codes
Philips 09
RCA 05, 06
Samsung 24
Sanyo 21, 22, 23
Sharp 27, 28
Shinton 30
Sony 18, 19, 20
Toshiba 26
Zenith 08
To change the transmittable signals for
operating a CATV converter or satellite tuner
1. Press and hold CATV/SAT POWER.
2. Press CATV CONTROL.
3. Enter manufacturer's code (two digits) using
buttons 1–9, and 0.
See the list below to find the code.
Examples: For a JVC product, press 1, then 4.
For a SONY product, press 2, then 0.
4. Release CATV/SAT POWER.
Following button can be used for operating the CATV converter
or the satellite tuner:
CATV/SAT POWER: Turns on and off the CATV converter
or satellite tuner.
After pressing CATV CONTROL, you can perform the
following operations on the equipment:
CATV CH +/–:
Changes the channels.
1 – 9, 0, 100+ (+10): Selects the channel.
100+ (+10) button will function as the
ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
RETURN: Alternates between previously selected
channel and the current channel.
Note:
Refer to the manual supplied with your CATV converter or satellite
tuner.
5. Try to operate your CATV converter or satellite
tuner by pressing CATV/SAT POWER.
When your CATV converter or satellite tuner turns on or off,
you have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or satellite tuner, try each one until the
correct one is entered.
Manufacturer Codes
Hamlin 15, 16, 17, 18 RCA
Jerrold 01, 02, 03, 04, Scientific Atranta 09, 10
05, 06, 07, 08 Sony
Pioneer 13, 14
Manufacturers' codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
Manufacturer Codes
19
20
Zenith 11, 12