Setting The Speakers For The Dsp Modes - JVC RX-6100VBK Instructions Manual

Setting the Speakers for the DSP Modes

To obtain the best possible surround sound of the DSP (Digital
Signal Processor) modes (see page 18), you have to register the
information about the speakers arrangement after all connections are
completed.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Front, Center, and Rear Speaker Setting
Register the sizes of all the connected speakers.
On the front panel ONLY:
1. Press SETTING repeatedly until
"FRONT SPK" (Front Speaker),
"CENTER SPK" (Center
Speaker), or "REAR SPK" (Rear
Speaker) appears on the display.
• Once you have pressed SETTING, MULTI CURSOR % / fi
can be also used for selecting the speakers.
2. Press MULTI CURSOR @ / # to
select the appropriate item about
the speaker selected in the above
step.
• As you press it, the display changes to
show the following:
LARGE SMALL
LARGE: Select this when the speaker size is relatively large.
SMALL: Select this when the speaker size is relatively small.
NONE: Select this when you have not connected a speaker.
(Not selectable for the front speakers)
3. Repeat steps 1 and 2 to select the appropriate
items for the other speakers.
Notes:
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 4 3 / inches (12 cm), select "LARGE," and if it is smaller than
4
4 3 / inches (12 cm), select "SMALL."
4
• If you have selected "NO" for the subwoofer setting, you can only
select "LARGE" for the front speaker setting.
• If you have selected "SMALL" for the front speaker setting, you
cannnot select "LARGE" for the center and rear speaker settings.
• When you change your speakers, you need to register the
information about the speaker again.
12
Center Delay Time Setting
Register the delay time of the sound from the center speaker,
comparing that of the sound from the front speakers.
If the distance from your listening point to the center speaker is
equal to that to the front speakers, select 0 msec. As the distance to
the center speaker becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 11
inches (30 cm) decrease (or increase) in distance.
• When shipped from the factory, delay time is set to 0 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
"CENTER DELAY" appears on
the display.
• Once you have pressed SETTING, MULTI CURSOR % / fi
SETTING
• The display changes to show the current setting.
2. Press MULTI CURSOR @ / # to
select the delay time of the center
speaker output.
• Pressing # increases the delay time from
• Pressing @ decreases the delay time from
MULTI CURSOR
Rear Delay Time Setting
Register the delay time of the sound from the rear speakers,
comparing that of the sound from the front speakers.
NONE
If the distance from your listening point to the rear speakers is equal
to that to the front speakers, select 0 msec. As the distance to the rear
speakers becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 11
inches (30 cm) decrease (or increase) in distance.
• Rear delay time for Dolby Digital and DTS Digital Surround is to
be set to 5 msec.
• When shipped from the factory, delay time is set to 5 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
"REAR DELAY" appears on the
display.
• Once you have pressed SETTING, MULTI CURSOR % / fi
• The display changes to show the current setting.
2. Press MULTI CURSOR @ / # to
select the delay time of the rear
speaker output.
• Pressing # increases the delay time from
• Pressing @ decreases the delay time from
can be also used for selecting "CENTER DELAY."
0 msec ("C. DELAY: 0ms") to 5 msec ("C.
DELAY: 5ms").
5 msec ("C. DELAY: 5ms") to 0 msec ("C.
DELAY: 0ms").
can be also used for selecting "REAR DELAY."
0 msec ("R. DELAY: 0ms") to 15 msec
("R. DELAY: 15ms").
15 msec ("R. DELAY: 15ms") to 0 msec
("R. DELAY: 0ms").
13 /
16
SETTING
MULTI CURSOR
13
/
16
SETTING
MULTI CURSOR