Related Manuals for Uninterruptible Power Supplies Online UPS 1K
Summary of Contents for Uninterruptible Power Supplies Online UPS 1K
- Page 1 User Manual Rack/Tower Online UPS 1K/1.5K/2K/3K Uninterruptible Power Supply System Version: 1.2...
-
Page 2: Table Of Contents
Table of Contents 1. Important Safety Warning ............... 1 1-1. Transportation ................. 1 1-2. Preparation ..................1 1-3. Installation ..................1 1-4. Operation ..................1 1-5. Maintenance, service and faults ............2 2. Installation and setup ................3 2-1 Rear panel view ................3 2-2. -
Page 3: Important Safety Warning
1. Important Safety Warning Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and read carefully the following instructions before installing the unit. Do not operate this unit before reading through all safety information and operating instructions carefully 1-1. -
Page 4: Maintenance, Service And Faults
1-5. Maintenance, service and faults The UPS system operates with hazardous voltages. Repairs may be carried out only by qualified maintenance personnel. Caution - risk of electric shock. Even after the unit is disconnected from the mains (building wiring outlet), components inside the UPS system are still connected to the battery and electrically live and dangerous. -
Page 5: Installation And Setup
2. Installation and setup NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. Please keep the original package in a safe place for future use. NOTE: There are two different types of online UPS: standard and long-run models. Please refer to the following model table. -
Page 6: Install The Ups
1. Programmable outlets: connect to non-critical loads. 2. Output receptacles: connect to mission-critical loads. 3. AC input 4. Input circuit breaker 5. Network/Fax/Modem surge protection 6. Emergency power off function connector (EPO) 7. USB communication port 8. RS-232 communication port 9. -
Page 7: Setup The Ups
Tower Installation Step 1 Step 2 Step 3 2-3. Setup the UPS Step 1: UPS input connection Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords. Step 2: UPS output connection For socket-type outputs, there two kinds of outputs: programmable outlets and general outlets. Please connect non-critical devices to the programmable outlets and critical devices to the general outlets. -
Page 8: Battery Replacement
Step 5: Disable and enable EPO function Keep the pin 1 and pin 2 closed for UPS normal operation. To activate EPO function, cut the wire between pin 1 and pin 2. It’s in closed status for UPS normal operation. Step 6: Turn on the UPS Press the ON/Mute button on the front panel for two seconds to power on the UPS. -
Page 9: Battery Kit Assembly (Option)
Step 4 Step 5 Step 6 Remove the top cover of After replacing the Re-connect the battery wires. battery box and replace the batteries, put the battery inside batteries. box back to original location and screw it tightly. Step 7 Put the front panel back to the unit. - Page 10 3-battery kit Step 1: Remove adhesive tapes. Step 2: Connect all battery terminals by following below chart. Tapes Tapes Step 3: Put assembled battery packs on Step 4: Cover the other side of plastic shell as one side of plastic shells and insert one below chart.
- Page 11 Step 3: Put assembled battery packs on Step 4: Cover the other side of plastic shell as one side of plastic shells. below chart. Then, battery kit is assembly well. 6-battery kit Step 1: Remove adhesive tapes. Step 2: Connect all battery terminals by following below chart.
-
Page 12: Operations
3. Operations 3-1. Button operation Button View Button Function Turn on the UPS: Press and hold ON/Mute button for at least 2 seconds to turn on the UPS. Mute the alarm: After the UPS is turned on in battery mode, press and hold this button for at least 5 seconds to disable or enable the alarm system. -
Page 13: Battery Information
Display Function Backup time information Indicates the backup time in pie chart. Indicates the backup time in numbers. H: hours, M: minute Warning & Fault information Indicates that the warning and fault occurs. Indicates the warning and fault codes, and the codes are listed in details in 3-5 section. -
Page 14: Audible Alarm
3-3. Audible Alarm Battery Mode Sounding every 4 seconds Low Battery Sounding every second Overload Sounding twice every second Fault Continuously sounding 3-4. LCD display wordings index Abbreviation Display content Meaning Enable Disable Escape Rack display Tower display Low Battery Overload Battery is not connected Overcharge... -
Page 15: Ups Setting
3-5. UPS Setting There are two parameters to set up the Parameter 2 UPS. Parameter 1: It’s for program alternatives. There are 9 programs to set up: Parameter 1 Parameter 2: It’s for setting information display。 01: Output voltage setting ... - Page 16 04: ECO enable/disable Interface Setting ENA: ECO mode enable DIS: ECO mode disable 05: AECO enable/disable Interface Setting ENA: Advanced ECO mode enable DIS: Advanced ECO mode disable 06: Bypass mode enable/disable Interface Setting ENA: Bypass mode enable DIS: Bypass mode disable 07: Programmable outlets enable/disable ...
- Page 17 08: Programmable outlets setting Interface Setting 0-999: setting the backup time limits in minutes from 0-999 for programmable outlets which connect to non-critical devices on battery mode. 09: LCD display direction setting Interface Setting RAC: the LCD display is horizontal. TOE: the LCD display is vertical.
-
Page 18: Operating Mode Description
3-6. Operating Mode Description Operating Description LCD display mode Rack Display Tower Display Online mode When the input voltage is within acceptable range, UPS will provide pure and stable AC power to output. The UPS will also charge the battery at online mode. -
Page 19: Faults Reference Code
Standby UPS is powered off without output mode power, but the battery still can be charged. Fault mode The UPS is in fault mode when no output power is supplied from the UPS and the fault icon flashes on the LCD display, although the information of UPS can be displayed in the screen. -
Page 20: Troubleshooting
4. Troubleshooting If the UPS system does not operate correctly, please solve the problem by using the table below. Symptom Possible cause Remedy No indication and alarm even The AC input power is not Check if input power cord though the main is normal. connected well. - Page 21 Symptom Possible cause Remedy Fault code is shown as 43 and The The UPS shut down Remove excess loads from icon is lighting on LCD automatically because of UPS output and restart it. display and alarm is continuously overload at the UPS sounding.
-
Page 22: Storage And Maintenance
5. Storage and Maintenance 5-1. Operation The UPS system contains no user-serviceable parts. If the battery service life (3~5 years at 25°C ambient temperature) has been exceeded, the batteries must be replaced. In this case, please contact your dealer. Be sure to deliver the spent battery to a recycling facility or ship it to your dealer in the replacement battery packing material. -
Page 23: Specifications
6. Specifications MODEL 1.5K 1.5KL Capacity VA/W 1000 VA / 900 W 1500 VA / 1350 W 2000 VA / 1800 W 3000 VA / 2700 W INPUT Low Line 80 VAC/70 VAC/60 VAC/55 VAC ± 5 % or 160 VAC/140 VAC/120 VAC/110 VAC ± 5 % Transfer (based on load percentage 100%-80% / 80%-70% / 70%-60% / 60%-0) Low Line...