When Mounting The Camera Directly To The Ceiling Or On The Wall - JVC TK-C210FW Instructions Manual

Installation and connection (continued)
Mounting the Camera to the
Ceiling (continued)
When mounting the camera directly to
the ceiling or on the wall
When mounting to a wall, replace areas indicated
as "ceiling" in the procedures by "wall".
Setup
1.
Open a hole in the ceiling. (R30 mm)
Make use of the template supplied to open a hole.
2.
Draw the fall prevention wire mounted to
the ceiling slab and the cable out from the
ceiling in advance.
CAUTION:
● Select a suitable safety cable based on
length, strength, location, material
(insulation property), etc.
● Use a ring on the fall prevention wire for
mounting to the camera unit with an
internal diameter of at least R3.1 mm or
and not larger than R5.5 mm, and an
external diameter that is not larger than
R 9 mm.
3.
Remove the dome cover.
As illustrated in the diagram, hold the dome
ring such that the position mark comes
between the thumb and index finger. Turn the
ring in the anti-clockwise direction to remove.
3.
Dome Ring Position mark
4.
Remove the outer case.
A
Loosen the camera fastening screw with a
screwdriver.
B
To remove, turn the camera unit in the anti-
clockwise direction.
C
Dismantle the fall prevention wire.
5.
Loosen the pan fastening screw.
CAUTION:
● Moving the lens unit without loosening the
pan fastening screw may damage the lens
unit.
20
6.
Set the switches for video images.
(TK-C215V4 A pg. 10)
(TK-C215V12 A pg. 12)
(TK-C210FW A pg. 14)
5.
4.
Pan fastening
Screw
6.
Camera
Fastening
Screw
4.
*TK-C215V4 is used in the above illustration
Connecting
1.
Align j with the shooting direction when
mounting the cover to the ceiling.
Mount by using the supplied adapter ring to
clamp between the outer case and the ceiling.
Notes on outer case mounting screws
(not supplied):
● The diameter of the attachment hole of
outer case is R4.5 mm (3/16 inch).
● Do not use flathead screws.
● When using an impact screwdriver, do not
tighten the screws fully. Tighten using your
hand instead. Failure to do so may damage
the outer case.
2.
Hang the fall prevention wire that has been
dismantled in Step 4 C of the setup
procedures to the hook.
3.
Attach the fall prevention wire to the
camera.
(Fall prevention wire is not included)
CAUTION:
● Tighten all screws securely. Otherwise the
camera may come loose and fall.
Installation and connection (continued)
Adaptor ring
1.
Attach from
2.
the ceiling
slab
Fall preven- 3.
tion wire
(not supplied)
Be sure to loosen
the screw.
*TK-C215V4 is used in the above illustration
4.
Connect the video signal cable. (A pg. 14)
Lower the protection cover and connect the
connectors. Upon connecting, restore the
protection cover to cover the connectors.
5.
Connect the input power supply cable.
(A pg. 15)
6.
Install the Ferrite core (TK-C210FW only)
(A pg. 14)
7.
Connect the alarm cable.
(TK-C215V12 only) (A pg. 15)
8.
Wrap insulation tape around cables.
Alarm signal cable
(TK-C215V12 only)
5.7.
Solder or crimp
4.
Insulation tape
Protection
Wrap with tape
cover
8.
Input power
supply cable
*TK-C215V12 is used in the above illustration
Mounting
1.
Align the position mark of the fastened
outer case with that of the camera unit.
NOTE:
When doing so, be careful not to catch the
cables in the outer case.
2.
Turn the camera unit in the clockwise
direction.
T When doing so, ensure that the X mark is
visible. (See illustration below)
3.
Fasten the camera by tightening the camera
fastening screw.
Position
mark
2.
1.
T Check
Camera
fastening screw
3.
*TK-C215V4 is used in the above illustration
Adjusting Images
After mounting is completed, adjust the
images while checking the actual image.
(A pg. 23 Adjusting Images )
21