Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JVC LST0420-001B
Summary of Contents for JVC LST0420-001B
-
Page 1: Dome Camera
DOME CAMERA TK-C215V4 TK-C215V12 For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. TK-C215V4/TK-C215V12 Serial No. INSTRUCTIONS *TK-C215V4 is used in the above illustration. LST0420-001B... -
Page 2: Introduction
European Union. If you wish to dispose of this product, please visit our web page www.jvc-europe.com to obtain information about the take-back of the product. [Other Countries outside the European Union] If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment. - Page 3 ● Consult the dealer or an experienced radio/ TV technician for help. CAUTION CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER'S AUTHORITY TO OPERATE THE EQUIPMENT. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
-
Page 4: Important Safeguards
Introduction These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. -
Page 5: Table Of Contents
Contents Introduction Safety Precautions ... 2 Contents... 5 Characteristics ... 6 Operating Precautions ... 7 Name of Parts ... 8 Camera... 8 Camera (Interior) ... 9 Setting the Lens and Switches (TK-C215V4) ... 10 Setting the Lens and Switches (TK-C215V12) ... 12 Installation and connection About Connection Cables ... -
Page 6: Characteristics
Introduction Thank you for purchasing this product. (These instructions are for: TK-C215V4U/TK-C215V12U.) Before beginning to operate this unit, please read the instruction manual carefully in order to make sure that the best possible performance is obtained. Characteristics Realizing a High Picture Quality This camera realizes 540 TV lines and S/N50 dB by employing a highly sensitive CCD with 380,000 pixels and a high-resolution video... -
Page 7: Operating Precautions
Operating Precautions To save energy, when it is not being used turn the system’s power off. This camera has been designed for indoor use. It cannot be used outdoors. Do not install or use the camera in the following places. ●... -
Page 8: Name Of Parts
Introduction Name of Parts Camera Mounting hole (elliptical) x 4 Use these when mounting the camera to the electrical box. (A pg. 22) Mounting hole (round) x 4 Use these when mounting the camera to the ceiling or wall. (A pg. 18, 20) Outer Case Use this in the following cases: ●... -
Page 9: Camera (Interior)
Camera (Interior) The dome cover, inner dome and outer case are removed. Procedures for removal. (A pg. 18 Embedding the camera to the ceiling , Step 3. to Step 5.) *TK-C215V4 is used in the above illustration. Strap A plate to connect the camera unit and the dome cover. -
Page 10: Setting The Lens And Switches (Tk-C215V4)
Introduction Setting the Lens and Switches (TK-C215V4) Set the video setting switches on the camera unit before mounting it. To set the switches, use a fine-tipped screwdriver. RESET/ [ SPOT ] LL PHASE WHT. BAL. IRIS LEVEL FOCUS ADJUST Function selection switch setting table (Items in bold are factory position) SELECT PHASE... - Page 11 [WHT.BAL.] ATW/MANUAL selection switch. For selecting whether to adjust the white balance automatically or manually. When the setting is changed from manual to ATW, the setting values in the manual mode will be reset. The camera switches to the same mode as with pressing the [RESET] button.
-
Page 12: Setting The Lens And Switches (Tk-C215V12)
Introduction Setting the Lens and Switches (TK-C215V12) Set the video setting switches on the camera unit before mounting it. To set the switches, use a fine-tipped screwdriver. Function selection switch setting table (Items in bold are factory position) SELECT PHASE SYNC WHT.BAL. - Page 13 [SELECT] WHT.BAL./PHASE setting switch. WHT.BAL.: The F [R/B, +/-] buttons are used as [R/B] adjustment buttons. PHASE: The F [R/B, +/-] buttons are used as [+/-] adjustment buttons. (Default setting: WHT.BAL.) [SYNC] Synchronization system selection switch. This switch sets the synchronizing system for the camera.
-
Page 14: Installation And Connection
Installation and connection About Connection Cables The maximum connection distance varies with the type of cable used. Please refer carefully to the table for each cable during connection. * Be sure to turn off the power of devices before connecting cables. Video signal cables Connect the coaxial cables (BNC) to the video signal output connector (BNC). -
Page 15: Electrical Specifications Of Alarm Input Terminals
Electrical Specifications of Alarm Input Terminals (TK-C215V12 only) ● To prevent penetration of noise in the internal circuitry, apply a non-voltage contact signal to the ALARM input terminal. Never apply a voltage. ● Apply an alarm signal for at least 200 ms. If it is shorter, it is not guaranteed that the signal will be recognized as an alarm signal. -
Page 16: System Diagram
Installation and connection System diagram TK-C215V4 Video signal Power TK-C215V4 Video signal Power TK-C215V12 Video signal Power Alarm signal METAL CONTACT Power Unit DC 12 V or AC 24 V Digital Video Recorder etc. NOTE: ● Turn OFF the power supply to all equipment to be used before making connections. -
Page 17: Mounting The Camera
(recess bracket). ● For detail related to embedded cover (rsecess bracket), please contact JVC. *TK-C215V4 is used in the above illustration. Embedded Cover in Ceiling (recess bracket) Selecting a mounting method Select a method for mounting the camera according to the intended purpose. -
Page 18: Embedding The Camera To The Ceiling
Installation and connection Mounting the Camera (continued) Embedding the camera to the ceiling * Make use of a ceiling material with a thickness between 9.5 mm to 22 mm. Setup Open a hole in the ceiling. (R120 mm, 4 3/4 inches) Draw the fall prevention wire mounted to the ceiling slab and the cable out from the... - Page 19 Connecting Attach the fall prevention wire to the camera, followed by attaching it to the ceiling slab (Fall prevention wire is not included.) Connect the video signal cable. (A pg. 14) Lower the cover and connect the connectors. Upon connecting, cover the connectors using the protection cover.
-
Page 20: When Mounting The Camera Directly To The Ceiling Or On The Wall
Installation and connection Mounting the Camera (continued) When mounting the camera directly to the ceiling or on the wall When mounting to a wall, replace areas indicated as “ceiling” in the procedures by “wall”. Setup Open a hole in the ceiling. (R 30 mm, 1 1/8 inches) Make use of the template supplied to open a hole. -
Page 21: Adjusting Images
Attach from the ceiling slab Fall prevention wire (not supplied) TK-C215V4 is used in the above illustration. Connect the video signal cable. (A pg. 14) Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors. Connect the input power supply cable. -
Page 22: When Mounting The Camera To The Electrical Box
Installation and connection Mounting the Camera (continued) When mounting the camera to the electrical box NOTE: Before mounting the camera to electrical boxes, please refer to local building codes for box type to use for low-voltage wiring. Connecting Align j with the shooting direction when mounting the cover to the electrical box. -
Page 23: Adjusting Image
Adjusting Image Adjusting Images Upon mounting the camera, adjust the images while checking the actual image. Mounting the test monitor Connect the [MONITOR] terminal of this camera to a test monitor to adjust the camera’s shooting direction, image and focus. * The power to the camera body must be ON when adjustments are performed. -
Page 24: Adjusting The Field Angle/Focus/Brightness
Adjusting Image Adjusting Images (continued) Adjusting the field angle/focus/ brightness Upon determining the imaging direction, adjust the field angle, focus and iris level accordingly. The method of adjustment varies with the camera in use. TK-C215V4 (A pg. 24) TK-C215V12 (A pg. 25) TK-C215V4 Iris Level Adjustment... - Page 25 TK-C215V12 ● 2 types of angle of view may be selected for TK-C215V12. In general, set in a way such that the home position shoots a wide range and the alarm position a narrow range. ● Use the alarm input mode selection switch to set the actions when there is an alarm input.
- Page 26 Adjusting Image Adjusting Images (continued) TK-C215V12 (continued) Registering alarm position For registering the angle of view during monitoring when there is an alarm input. 2.,3. 1.,5. Check that the [ALARM POSITION] indicator light is turned on. Registration of alarm position is enabled. ●...
-
Page 27: Other Installation And Adjustment
Other installation and adjustment Mounting the Inner Dome After setting is complete, mount the Inner dome. *TK-C215V4 is used in the above illustration. Mount the inner dome . Mount the inner dome to the claws (3 locations). CAUTION: ● Mount the inner dome such that it does not cover the lens. -
Page 28: White-Spot Correction
Other installation and adjustment White-spot correction As a general characteristic unique to CCDs, white-spots may appear on the screen with age. In order to reduce this phenomenon, this unit is equipped with a white-spot correction feature. Switch on the camera power supply and wait for at least 30 minutes. -
Page 29: Others
Others Specifications Camera Signal system : Based on NTSC standard Scanning frequencies : 15.734 kHz (Horizontal), 59.94 Hz (Vertical) Image device: 1/4" IT CCD Effective picture elements: : 380,000 pixels, 768 (H) x 494 (V) Sync system : Line lock/Internal Video S/N: 50 dB (AGC OFF, white 50 % output) - Page 30 Others Specifications (continued) External Dimensions [Unit: mm (inches)] When cover is attached 121 (4-3/4) 4-R4,5 46 (1-13/16) (3/16) 6(1/4) R156 (6-1/8) When embedded R116 (4-9/16) R145 (5-3/4) * Specifications and appearance of this unit and related products are subject to change for product improvement without prior notice.
- Page 31 Focus chart...
- Page 32 LST0420-001B © 2006 Victor Company of Japan, Limited...