Setting The Lens And Switches - JVC TK-C210FW Instructions Manual

Introduction (continued)
Setting the Lens and
Switches (TK-C215V4)
Set the video setting switches on the camera unit
before mounting it.
To set the switches, use a fine-tipped screwdriver.
RESET/ [ SPOT ]
LL PHASE
O
1
N
2 2
3
4 4
5
WHT.
6
BAL.
7
8
L H
IRIS
LEVEL
FOCUS ADJUST
Function selection switch setting table
(Items in bold are factory position)
OFF ON
1 AGC OFF ON
SELECT PHASE WHT.BAL.
2
3 SYNC LL INT
4 WHT.BAL. ATW MANU
5 BLC OFF ON
6 DAY/NIGHT OFF ON
7 RESERVED SET TO OFF
8 RESET/SPOT RESET
SPOT
10
A
[RESET/SPOT] RESET/SPOT button
When this button is pressed, the value of the
white balance or phase adjusted manually is
reset to the default value.
● When the 2 [SELECT] switch is set to
WHT.BAL., the white balance is reset to the
default value.
When the switch is set to PHASE, the phase
is reset to the default value.
● When setting to SPOT:
When this button is pressed, white spots are
corrected.
For instructions on correcting white spots, see
White-spot correction (A pg. 27).
B
[R/B, +/-] R/B, +/- adjustment button
This button is pressed when manually
adjusting the white balance or when adjusting
the vertical phase of the line lock.
The function of this button is selected using
the 2 [SELECT] switch.
● When manually adjusting the white balance:
Press the R button to increase the red tint and
decrease the blue tint.
Press the B button to increase the blue tint
and decrease the red tint.
● When adjusting the phase:
Press the + or - button to adjust the phase.
C
Function selection switches
1.
[AGC] Auto-gain control switch.
Setting this switch to ON automatically
increases the sensitivity even when the
brightness of the subject is insufficient.
(Default setting: ON)
2.
[SELECT] WHT.BAL./PHASE setting switch.
WHT.BAL.:
The B [R/B, +/-] buttons are used as [R/B]
adjustment buttons.
PHASE:
The B [R/B, +/-] buttons are used as [+/-]
adjustment buttons.
(Default setting: WHT.BAL.)
3.
[SYNC] Synchronization system selection
switch.
This switch sets the synchronizing system for
the camera.
INT:
This is set for internal synchronization
LL (Line Lock):
The camera's vertical synchronization is
locked to the AC 24 V power line frequency.
When switching between multiple cameras
using a switcher, selecting this mode and
adjusting the vertical phase can reduce the
monitor sync disturbances occur that when
the camera image is switched.
U type: 60 Hz only
E type: 50 Hz only
(Default setting: INT)
4.
[WHT.BAL.] ATW/MANUAL selection switch.
For selecting whether to adjust the white
balance automatically or manually.
When the setting is changed from manual to
ATW, the setting values in the manual mode
will be reset. The camera switches to the
same mode as with pressing the [RESET]
button.
(Default setting: ATW)
NOTE:
● The white balance of this camera is preset
to use under sunlight or halogen lamps,
and may not be properly adjusted when
used under artificial lights such as
fluorescent lights.
5.
[BLC] Backlight compensation switch.
When the object is placed against the light,
setting this to ON increases the iris aperture
by 1 stop and the object will appear clearer.
(Default setting: OFF)
6.
[DAY/NIGHT] Easy Day & Night switch.
To capture a subject with continually changing
brightness (day/night), set this switch to ON .
The camera automatically captures the image
in color when the subject is bright, and in
black and white mode when it is dark.
(Default setting: OFF)
NOTE:
● When this item is set to ON , the AGC
feature will automatically be set to ON
regardless of the [AGC] Switch 1 setting.
● The Easy DAY & NIGHT feature on this
camera uses a sensitized black and white
mode unlike other black and white
surveillance cameras that use infra-red
lighting.
● Sensitivity increases in the case of black-
and-white images. The screen may
therefore appear rougher and white spots
may increase.
7.
[RESERVED]
Not used. Ensure to set this to OFF before
using the camera.
(Default setting: OFF)
8.
[RESET/SPOT] RESET/SPOT CORRECTION
selection switch.
RESET:
The [RESET/SPOT] button is used as a
[RESET] button.
SPOT:
The [RESET/SPOT] button is used as a
[SPOT] button. (A pg. 27)
(Default setting: RESET)
D
[IRIS LEVEL] Iris level adjustment
For adjusting the level of the automatic
aperture control lens. This adjustment only
needs to be made when required. Use this to
accommodate particular shooting conditions.
To darken image: Counterclockwise (L side)
To brighten image: Clockwise (H side)
NOTE:
Prior to adjusting the aperture level, ensure to
set the [AGC] Switch 1 of the function
selection switch C to OFF . Otherwise,
when the level is turned too far toward L, the
AGC function activates increasing sensitivity
and the picture may look uneven.
E
[FOCUS ADJUST] focus adjustment button
Use this to adjust the lens focus.
Upon pressing, the lens aperture will open up
for about 30 seconds such that the depth of
field becomes shallower, thus enabling focus
to be easily adjusted. (A pg. 25)
NOTE:
The electronic shutter functions automatically
upon pressing the focus adjustment button
and the screen may flicker. However, this is
not a malfunction.
F
Focus adjustment ring
Move this to the left/right to adjust the focus.
G
Zoom adjustment ring
Move this to the left/right to adjust the field
angle.
11