Potterton Eurocondense Plus Installation Manual page 33

ADJUSTEMENT TABLE FOR HEATING ENGINEERS
Display on room control module RRG Function
BUM parameter final user level
.
Program No.
546 ZBreMinL
547 ZReglVerz
551 Kon
552 HydrSystem
553 KonfigHks
555 KonfigRg1
556 KonfigRg2
557 KonfigRg3
558 KonfigRg4
561 KonfigRg7
562 pH2Omin
563 pH2Omax
584 ZkickFkt
596 ZeitAufZu
598 LmodRgVerz
604 LPBKonfigO
605 LPBAdrGerNr
606 LPBAdrSegNr
607 TbwBereit
614 KonfigEingang
615 KonfigAusgang
618 KonfigEingangR
619 KonfigAusgang1R
620 KonfigAusgang2R
621 KonfigAusgang3R
622 TAnfoExtMax
623 PAnfoExtSchwelle
Minimum running time for burner
Control delay after burner startup
Constant for rapid reduction (without
room influence)
Hydraulic system setting Assignment of HKM
or RRG to heating circuit [0...255], see Table 11
Adjustment codes
Adjustment codes
Adjustment codes
Adjustment codes
Adjustment codes
Min. boiler water pressure
Max. boiler water pressure
Time for pump output kick function
Running time for drive in heating circuit 2 (CIM); 30 to 873 s 150 s
Output during control delay time
Adjustment code for bus module CIB
LPB application address for BMU
LPB segment address for BMU
Reduced setting for hot water
Programmable input F2
0 = Standard; 1 = Modem function
2 = Modem function "neg. logic" 3 = Door veil
Programmable output M5
0 = Standard; 1 = Signal output; 2 = Alarm output,
3 = Operating signal, 4 = External transformer
(transformer T2); 5 = M5 (Q2Y2);
6 = DHW circulation pump; 7 = Door veil;
8 = Primary loop pump; 9 = RegC1;
10 = Basic function K2; 11 = DHW loading
function (layer tank only); 12 = Analog threshold
Programmable input on relay module:
0 = Standard (no function); 1 = modemfunction;
2 = modemfunction; 3 = door veil; 4 = temperature
setpoint; 5 = heat output setpoint; 6 = sensor
hydraulic switch
Note: with CISP, only 4 and 5 possible
Function of output 1 relay module
0 = Standard; 1 = Signal output; 2 = Alarm output,
3 = Operating signal, 4 = External transformer
(transformer T2); 5 = M5 (Q2Y2);
6 = DHW circulation pump; 7 = Door veil;
8 = Primary loop pump; 9 = not possible;
10 = Basic function K2; 11 = not possible
12 = Analog threshold
Function of output 2 relay module
Setting as parameter 619
Function of output 3 relay module
Setting as parameter 619
Max. value of heat demand in case of external
temperature setting (if param. 618 = 4)
Switchpoint of the analog threshold
(% of max. value) (if param. 618 = 5)
Basic setting New
(set at factory) setting *)
0 s
2)
60 s
4
2
21
00110100
00000000 (not used)
00000100 (not used)
01000000
00001110
0,7 bar (not activated)
2,5 bar (not activated)
2)
5 s
2)
25 %
00010000
1 - -
0 - -
40 °C
0
2
0
3
3
0
100 °C
5 %
33