Panasonic KX-TEA308 Features Manual page 109

DISA Busy Mode
If the destination of a DISA call is busy, the call will be redirected to an idle extension (
[100]) in the destination's idle extension hunting group (
the group is available, or if the destination of the DISA call is not a member of an idle extension hunting
group, the call will be handled in one of the following ways, according to system programming (
Mode [506]):
a)
Disconnect: The caller hears a busy tone and the call is disconnected.
b)
Call Waiting: The called extension hears a call waiting tone if the extension has set Call Waiting.
c)
DISA: The following procedure is performed:
1)
If the assigned DISA OGM (busy message) has been recorded, the caller hears the DISA
OGM (e.g., "The party you called is unavailable..."). If the assigned DISA OGM has not been
recorded, the caller hears a busy tone and the call is disconnected.
2)
After the busy message has been played, the DISA OGM that was sent before the busy
message is sent to the caller again.
3)
The PBX waits for the caller to enter a new destination. In this case, the PBX does not accept
any Outside Line Access number regardless of the security type.
If the destination is a member of a DISA ring group, DISA Busy Mode will not function for the call. The PBX
regards it as unanswered.
DISA Intercept Mode
If the destination of a DISA call does not answer the call within a preprogrammed time period (
Time before Intercept [508]), the call will be handled in one of the following ways, according to system
programming ( DISA Intercept Mode [507]):
a)
Disconnect: The call is disconnected.
b)
Intercept: The call is redirected to preprogrammed intercept destinations in the following priority:
DISA IRNA to BV—Day/Night/Lunch [438-440]
This is useful for business calls. For example, the call can be forwarded to the operator, a Voice
Processing System (VPS) or Built-in Voice Message (BV) automatically.
DISA No Dial Mode
If the PBX does not receive either DTMF (Dual Tone Multi-Frequency) signals or a fax (CNG) tone within a
preprogrammed time period (
signals within a preprogrammed time period (
handled in one of the following ways, according to system programming (
a)
Disconnect: The call is disconnected.
b)
Intercept: The call is redirected to preprogrammed intercept destinations in the following priority:
DISA IRNA to BV—Day/Night/Lunch [438-440]
DISA Security Mode
Security can be enabled for the PBX to control the types of calls that can be made by callers using DISA.
When the DISA security mode is set to "All Security" or "Trunk Security" (
caller is required to enter a DISA security code (
outside (CO) line calls, or outside (CO) line calls only, respectively. The DISA security code and the number
of digits required for the DISA security code (
manager. After entering a DISA security code, if the code is the same as one of the preprogrammed security
codes, the caller will hear a short beep. It is possible to eliminate the tone through system programming (
DISA Tone after Security Code [518]).
If the DISA security code is entered incorrectly 3 times when using DISA, a reorder tone will be sent to the
caller and the call will be disconnected.
DISA Wait Time after OGM [505]), or if the PBX does not receive DTMF
Intercept Time for Internal DISA [515]), the call will be
DISA Security Code [512]) before making intercom and
DISA Security Code Digits [530]) can be assigned by the
1.15 Optional Device Features
1.2.1 Idle Extension Hunting). If no extension in
Flexible Ringing—Day/Night/Lunch [408-410]
DISA No Dial Mode [510]):
Flexible Ringing—Day/Night/Lunch [408-410]
DISA Security Mode [511]), a
Hunting Group Set
DISA Busy
DISA Ring
Feature Guide 109