Epson LX-300+II RTP Service Manual page 116

EPSON LX-300+II/300+II RTP/1170II
Table A-13. EEPROM Address Map (continued)
Address Explanation
b0: Font function
b1: (reserved)
b2: Pause function
b3: (reserved)
3CH Panel mask pattern 2
b4: (reserved)
b5: (reserved)
b6: (reserved)
b7: (reserved)
Copy mode b0: copy mode
----- b1: (reserved)
----- b2: (reserved)
----- b3: (reserved)
3DH
Energy save mode b4: Energy save mode
----- b5: (reserved)
----- b6: (reserved)
----- b7: (reserved)
Tear-off adjustment -432 to +432 (-25.4 mm (-1inch) to 0 mm
3E,3FH
value +25.4 mm (1inch), by 0.0588 mm (1/432 inch)
40H Tear-off wait time 3 to 30 (by 0.1 sec.), 00H:3 sec.(same as default)
Manual insertion wait 3 to 30 (by 0.1 sec.), 00H:1.5 sec.(same as
41H
time default)
42H-4FH (reserved)
Area 2
50H-51H (reserved)
52H-5AH
USB ID
5BH-63H
00H: Error is not recorded
30H: CR Error
32H: CG Error
64H Fatal error (Latest)
33H: Head Low Volt Error
3AH: Head open Error
3BH: EEPROM Compare Error
65H Fatal error (Record #1) (The same as the above)
66H Fatal error (Record #2) (The same as the above)
67H Fatal error (Record #3) (The same as the above)
Sub-number for
68H-6AH 00H to 09H
customization
6BH (reserved)
6CH Market CG 0:Standard version 1:NLSP version
Appendix
QPIT Factory
Setting
Settings Settings
00H 00H
0: Off 1: On
00H 00H
0: On 1: Off
0000H 0000H
00H 00H
(3 sec.) (3 sec.)
00H 00H
(1.5 sec.) (1.5 sec.)
All 00H All 00H
00H 00H
All 00H *a)
All 00H *a)
00H 00H
00H 00H
00H 00H
00H 00H
000000H 000000H
(Standard) (Standard)
00H 00H
00H 00H
EEPROM Address Map
Table A-13. EEPROM Address Map (continued)
Address Explanation
6DH IBM character table 0:Table2 1:Table1
6EH (reserved)
6FH (reserved)
70H Vp adjustment value
Vp adjustment value
71H
(complement of 70H)
Bi-d adjustment value
72H for high speed draft -12 to +12 by 0.0353 mm(1/720 inch)
mode
Bi-d adjustment value
73H -12 to +12 by 0.0353 mm(1/720 inch)
for draft mode
Bi-d adjustment value
74H -12 to +12 by 0.0353 mm(1/720 inch)
for NLQ mode
75H-7BH (reserved)
RPE (TOF) position
7CH adjustment for -128 to +127 by 0.0588 mm (1/432 inch)
continuous
RPE (TOF) position
7DH adjustment for -128 to +127 by 0.0588 mm (1/432 inch)
continuous
RPE (TOF) position
7EH adjustment for -128 to +127 by 0.0588 mm (1/432 inch)
continuous
7FH (reserved)
Revision D
QPIT
Setting
Settings
00H
00H
00H
Area 3
*a)
*a)
00H
00H
00H
All 00H
00H
00H
00H
00H
Factory
Settings
00H
00H
00H
*a)
*a)
*a)
*a)
*a)
00H
*a)
*a)
*a)
00H
116