WAGNER ProSpray 3.29 Operating Manual
Airless high-pressure spraying unit
Hide thumbs
Also See for ProSpray 3.29:
- Owner's manual (144 pages) ,
- Operating manual (103 pages) ,
- Original operating manual (36 pages)
Related Manuals for WAGNER ProSpray 3.29
Summary of Contents for WAGNER ProSpray 3.29
- Page 1 ® Operating manual ProSpray 3.29 • 3.31 Airless high-pressure spraying unit Models: 0558014 0558015 0558016 0558029 0558299 0558387 0558388 Original operating manual ProSpray 3.29 • 3.31 Edition 3 / 2010 0558 938A...
- Page 2 Warning! Attention: Danger of injury by injection! Airless units develop extremely high spraying pressures. Never put your fingers, hands or any other parts of the body into the spray jet! Never point the spray gun at yourself, other persons or animals. Never use the spray gun without safety guard.
-
Page 3: Table Of Contents
11.2 Inlet and outlet valve ............16 Functioning of the unit ............6 11.3 Packings.................17 Legend for explanatory diagram 11.4 ProSpray 3.29 / 3.31 connection diagram ...... 18 ProSpray 3.29 / 3.31 ............7 Explanatory diagram ProSpray 3.29 / 3.31 ...... 7 Appendix ...............19 Technical data ..............8... -
Page 4: Safety Regulations For Airless Spraying
Safety Regulations Safety regulations for Airless spraying This manual contains information that must be read and understood before using the equipment. When you come to an area that has one of the following symbols, pay particular attention and make certain to heed the safeguard. -
Page 5: Earthing Instructions
Safety regulations General view of application HAZARD: HAZARDouS VAPoRS HAZARD: EXPLoSIoN HAZARD DuE To INCoMPATIBLE MATERIALS Paints, solvents, insecticides, and other materials can be harmful if inhaled or come in contact with Will cause severe injury or property damage. body. Vapors can cause severe nausea, fainting, or poisoning. -
Page 6: General View Of Application
221 bar (22,1 MPa), the coating material No other materials should be used for spraying without is atomised. This high pressure has the effect of micro fine WAGNER’s approval. atomisation of the coating material. As no air is used in this process, it is described as an AIRLESS process. -
Page 7: Legend For Explanatory Diagram
Description of unit Legend for explanatory diagram ProSpray 3.29 / 3.31 1 Spray gun 9 Cart 2 High-pressure hose 10 Relief valve Lever position vertical – PRIME ( k circulation) 3 Oil cup for EasyGlide (EasyGlide prevents increased wear of the packings) Lever position horizontal – SPRAY ( p) -
Page 8: Technical Data
Description of unit Starting operation Starting operation Technical data ProSpray 3.29 ProSpray 3.31 High-pressure hose, spray gun and Voltage: 220~240 Volt, 50/60 Hz separating oil Max. current consumption: 7.5 A 1. Screw the high-pressure hose (2) to the coating material Power cord: 3 x 1.5 mm –... -
Page 9: Control Panel Indicators
Starting operation Solid Green When the pressure indicator is solid green, the sprayer is operating between 12 MPa (120 bar) and 23 MPa (230 bar). A solid green pressure indicator means: • The sprayer is at the proper pressure setting for spraying oil-based and latex house paints • The sprayer is operating at peak performance at a high pressure setting • If the pressure indicator goes to solid yellow when the pressure is set so that it starts at solid green, it indicates... -
Page 10: Cleaning Preserving Agent When Starting-Up Of Operation Initially
Starting operation Cleaning preserving agent when starting- Digital Electronic Spray Control (DESC) up of operation initially The Digital Electronic Spray Control (DESC) increases the functionality of the sprayer. It is installed directly below the 1. Immerse the suction tube (Fig. 7, Item 1) and return hose pressure control knob on the control panel. - Page 11 If you forget or misplace your security code, you can contact RUN TIME XXXX #4 key. Wagner customer service for assistance. To inactivate the security function, enter “1111” at the “Enter New Code Number” screen (this is the job Timers Screen default code that leaves the sprayer unlocked).
-
Page 12: Spraying Technique
High-pressure hose The unit is equipped with a high-pressure hose specially suited for piston pumps. 25 - 30 cm Only use WAGNER original-high-pressure hoses in order to ensure functionality, safety and durability. Interruption of work 1. Open the relief valve, valve position PRIME (k circulation). -
Page 13: Cleaning The Unit (Shutting Down)
Cleaning the unit (shutting down) Cleaning the unit (shutting down) Cleaning unit from outside A clean state is the best method of ensuring operation without problems. After you have finished spraying, clean the unit. Under First of all pull out mains plug from socket. no circumstances may any remaining coating material dry and harden in the unit. -
Page 14: Cleaning Airless Spray Gun
Cleaning the unit (shutting down) Remedy in case of faults Cleaning Airless spray gun Assembly 1. Place intake filter (3) with the long cone into the gun 1. Rinse Airless spray gun with an appropriate cleaning housing. agent. 2. Screw in grip (2) into the gun housing and tight en. 2. - Page 15 Once a problem occurs and the error message TEMPERATURE appears when the temperature of appears, the sprayer will shut down. the motor has risen too high. Take the sprayer to a Wagner authorized service center for repair. Before proceeding, relieve any pressure remaining in the system (valve position PRIME k).
-
Page 16: Servicing
General servicing remove the front cover. Servicing of the unit should be carried out once annually by the WAGNER service. Danger of crushing - do not reach with the 1. Check high-pressure hoses, device connecting line and fingers or tool between the moving parts. -
Page 17: Packings
Repairs at the unit 14. Unscrew lower housing (Fig. 13, Item 10) with adjusting 8. Push piston (4) downward out of the upper housing (6). wrench while holding the upper housing (11) securely with Check piston for wear and replace if necessary. a second adjusting wrench. 9. Remove upper packing (8) and lower packing (9) from the 15. -
Page 18: Prospray 3.29 / 3.31 Connection Diagram
30. Fasten return hose with clamp at suction tube. upper packing as a transportation device) for the piston 31. Install front cover. (Fig. 14, Item 4) onto the piston from above. 11.4 ProSpray 3.29 / 3.31 connection diagram EMI Filter White Power Cord Capacitor... -
Page 19: Appendix
Appendix Appendix 12.1 Selection of tip To achieve faultless and rational working, the selection of the tip is of the greatest importance. In many cases the correct tip can only be determined by means of a spraying test. Some rules for this: The spray jet must be even. -
Page 20: Airless Tip Table
12.4 Airless tip table WAGNER without tip without tip Trade Tip 2 F thread (11/16 - 16 UN) G thread (7/8 - 14 UN) up to 270 bar for Wagner spray guns for Graco/Titan spray guns Order no. 0556 042 Order no. 0556 041 (27 MPa) Application Spray Bore Spraying... -
Page 21: Tempspray
Appendix 12.5 TempSpray The paint material is heated to the required temperature uniformly by an electric heating element, which is located inside the hose (regulated from 20°C to 60°C). Advantages: • Constant paint temperature even at low outside temperatures • Considerably better working of high viscosity coating materials • Increased application efficiency • Savings in solvents due to reduction in viscosity • Adaptable to all airless units Order No. Description TempSpray H 126 (ideal for lacquer jobs) 2311659 Basic unit 1/4“ incl. stainless steel hose, DN6, 1/4“, 10m 2311852... -
Page 22: Pump-Runner
Appendix 12.6 Pump-Runner (order No. 2306987) Universal accessories for cleaning, clean transportation and preservation of the pump unit. Features: • Simpler cleaning – the cleaning liquid circulates constantly through the pump making thorough cleaning of the interior • No cleaning necessary during work stoppage or change of location because the paint in the pump cannot dry out or leak • Better protection • Simple assembly Suitable for the following models: Diaphragm Pumps Double-stroke piston pumps SF 21 Finish 270/370 PS 24 PS 3.25 SF 23 Nespray Deco PS 26 PS 3.29 SF 27 Nespray 31 PS 30... -
Page 23: Sales And Service Companies
Shibei Industrial Zone • Shanghai, 200436 China Tel. 0086/2166521858 • Fax: 0086/2166529819 • wagnersh@public8.sta.net.cn France J. Wagner France S.A.R.L. • Parc de Gutenberg - Bâtiment F • 8 voie la Cardon • 91127 Palaiseau Cedex Tel. +33/1/825 011 111 • Fax: +33/1/698 172 57 • division.batiment@wagner-france.fr Italia Wagner Colora S.R.L. -
Page 24: Accessories For Prospray 3.29 / 3.31
Accessories illustration ProSpray 3.29 / 3.31 ProSpray 3.29 • 3.31... - Page 25 Item Part No. Description 0296 388 Spray gun AG 08, F-thread 0296 386 Spray gun AG 08, G-thread 0502 166 Spray gun AG 14, F-thread 0502 119 Spray gun AG 14, G-thread 0296 441 Pole gun 120 cm, G-thread 7/8” 0296 443 Pole gun 120 cm, F-thread 11/16” 0296 442 Pole gun 200 cm, G-thread 7/8”...
-
Page 26: Spare Parts List For Main Assembly
Spare parts list ProSpray 3.29 / 3.31 Main Assembly 50 51 ProSpray 3.29 • 3.31... - Page 27 Item Part No. Description Item Part No. Description 0290 270 Motor shroud 0290 271 Screw (2) 0508 559 Screw (2) 0290 238 Fluid section assembly 0290 269 Belly pan 0507 783 Clip 9802 266 Screw (2) 0507 782 Suction tube 0290 228 Door 0290 253...
-
Page 28: Spare Parts List For Fluid Section
Spare parts list ProSpray 3.29 / 3.31 Fluid section ProSpray 3.29 • 3.31... - Page 29 Item Part No. Description 0290 263 Retainer 0290 255 Jam nut 0290 276 Spacer ------- Upper packing 0290 249 Upper housing 0508 343 Fitting ------- Lower packing 0508 712 Guide ring 0507 730 O-ring (2) 0507 731 O-ring (2) 0290 250 Lower housing 0290 251 Piston rod 0507 734...
-
Page 30: Spare Parts List For Drive Assembly
Spare parts list ProSpray 3.29 / 3.31 Drive Assembly Item Part No. Description 0558 323A Housing assembly 0290 241 Slider assembly 0290 254 Thrust washer 0290 239 Gear/crankshaft assembly 0290 240 1st stage gear 0558 324A Motor assembly 0508 559... -
Page 31: Spare Parts List Of Filter Assembly
Spare parts list ProSpray 3.29 / 3.31 Filter assembly Item Part No. Description 0508 723 Filter housing 14058 Conical spring 0507 748 Filter, 60 mesh (standard) 0508 451 Filter, 30 mesh 0508 452 Filter, 100 mesh 0508 603 Bearing ring... -
Page 32: Spare Parts List For Upright Cart
Spare parts list ProSpray 3.29 / 3.31 upright cart assembly Item Part No. Description 0290 207 Handle assembly (includes items 7-8) 9805 352 Screw (2) 0290 257 Bushing 0290 235 Cart weldment 9894 275 Spring 0290 244 Carriage assembly 0509 386... -
Page 33: Spare Parts List For Low Boy Cart
Spare parts list ProSpray 3.29 Low boy cart assembly Item Part No. Description 0290 290 Cart 0508 381 Drip cup 0290 291 Wheel 0294 534 Wheel spacer 9890 104 Axle cap 9805 230 Drip cup screw 0509 386 Washer 0295 608... -
Page 34: Spare Parts List For Suction System For Low Boy Cart
Spare parts list ProSpray 3.29 Suction system for low boy cart Item Part No. Description 0507 964 Return hose 0507 965 Siphon tube 5006 536 Inlet screen 0507 783 Clamp 0507 967 Siphon tube adapter ------- Tie wrap (not shown) -
Page 35: Important Notes On Product Liability
4 weeks of the day of delivery by the authorised specialist shop. for products that have been partially or fully taken apart. Registration can be completed on the Internet under www.wagner-group. com/profi-guarantee. The guarantee certificate is valid as confirmation, as is the original purchase document that carries the date of the 5. -
Page 36: Ce Declaration Of Conformity
Wagner or one of our dealers will take back your used Wagner waste electrical or electronic equipment and will dispose of it for you in an environmentally friendly way. Please ask your local Wagner service centre or dealer for details or contact us direct. Declaration of conformity Herewith we declare that the supplied version of WAGNER ProSpray 3.29 •...
Need help?
Do you have a question about the ProSpray 3.29 and is the answer not in the manual?
Questions and answers