Sun Microsystems Sun Fire T1000 Installation Manual
Installing the single-drive or dual-drive assembly in the server
Hide thumbs
Also See for Sun Fire T1000:
- Service manual (118 pages) ,
- Administration manual (80 pages) ,
- Installation manual (72 pages)
Related Manuals for Sun Microsystems Sun Fire T1000
Summary of Contents for Sun Microsystems Sun Fire T1000
- Page 1 Installing the Single-Drive or Dual- Drive Assembly in the Sun Fire ™ T1000 Server Sun Microsystems, Inc. www.sun.com Part No. 819-6673-10 July 2006, Revision A Submit comments about this document at: http://www.sun.com/hwdocs/feedback...
- Page 2 Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems, Inc. The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN...
- Page 3 Contents Preparing for Servicing 1 Removing the Single-Drive Assembly 3 Installing the Drive Assembly 4...
- Page 4 Installing the Single-Drive or Dual-Drive Assembly in the Sun Fire T1000 Server • July 2006...
-
Page 5: Preparing For Servicing
How to upgrade the drive assembly in the server from a single-drive assembly to ■ a dual-drive assembly How to install the single-drive assembly in a diskless Sun Fire™ T1000 server ■ How to install the dual-drive assembly in a diskless server ■... - Page 6 “Installing the Drive Assembly” on page If your server does not have any hard drives installed, go to “Installing the Drive ■ Assembly” on page Installing the Single-Drive or Dual-Drive Assembly in the Sun Fire T1000 Server • July 2006...
-
Page 7: Removing The Single-Drive Assembly
Removing the Single-Drive Assembly The procedure in this section describes how to remove the single-drive assembly from your server. 1. Disconnect the drive cable from the data/power connector at the rear of the hard drive ( FIGURE 2 2. Pull the fasteners up on the rear of the single-drive assembly, and remove the single-drive assembly from the chassis ( FIGURE 2 Removing the Single-Drive Assembly... -
Page 8: Installing The Drive Assembly
( FIGURE 3 Data connector (J5002) Data connector (J5003) Power connector Location of Drive Power and Data Connectors on the Motherboard FIGURE 3 Installing the Single-Drive or Dual-Drive Assembly in the Sun Fire T1000 Server • July 2006... - Page 9 3. Get the dual-drive cable that was shipped with the new drive assembly. 4. Plug the drive connectors into the data/power connectors at the rear of the hard drives. Note – Make sure the connector is correctly oriented before plugging it into the data/power connector on the drives.
- Page 10 RAID features. a. Determine the version of the drive controller firmware installed on your server by entering the following command: # grep -i version /var/adm/messages Installing the Single-Drive or Dual-Drive Assembly in the Sun Fire T1000 Server • July 2006...
- Page 11 You should see output similar to the following: Jun 7 13:23:16 wgs57-57 genunix: [ID 540533 kern.notice] SunOS Release 5.10 Version Generic_118833-08 64-bit Jun 7 13:23:16 wgs57-57 mpt0 Firmware version v1.a.0.0 (IR) If you see the following output: ■ Firmware version v1.a.0.0 or higher (for example, v1.b.0.0, ■...
- Page 12 Installing the Single-Drive or Dual-Drive Assembly in the Sun Fire T1000 Server • July 2006...
Need help?
Do you have a question about the Sun Fire T1000 and is the answer not in the manual?
Questions and answers