Revision History; Revision Code - Omron E5AK User Manual

A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
The following table outlines the changes made to the manual during each revision. Page numbers refer
to previous version.

Revision code

1
2
02A

Revision History

Cat. No. H083-E1-02A
Date
July 1996 Original production
Page 1- -7:
April 1997
Page V:
Page 1- -6:
Page 2- -8:
Page 3- -3:
Page 3- -8:
Page 5- -8:
Page 5- -9:
Page 5- -13:
Page 5- -14:
Page 5- -15:
Page 5- -16:
Page 5- -17:
Page 5- -23:
Page 5- -28:
Page 5- -33:
Page 5- -42:
Page 5- -43:
Page 6- -3:
Page 7- -4:
Page 7- -7:
Page 7- -9:
Page 7- -10:
Page 7- -12:
Page 7- -13:
Page 8- -4:
Page A- -2:
Page A- -11:
Page A- -14:
Page A- -15:
December 2003 Page 2- -9:
Page 4- -8:
Page 4- -9:
Page 5- -3:
Page A- -8:
Revision code
Revised content
Modified the diagram of mode.
Page 2- -6: Modified the power specifications in "Terminal arrange-
ment".
Changed "100 to 240 VAC" to AC100- -240V
Modified the item of "Model" on the table.
Modified the diagram in "Terminal arrangement".
Changed the Power specifications in "Power supply".
Modified the diagram in "Setup".
Added "run/stop"= "run" to Setting Example.
Added "Model" and "Power specifications" to MV monitor.
Added "Model" and "Power specifications" to Valve opening mon-
itor.
Added "Model" and "Power specifications" to Cooling coefficient.
Added "Model" and "Power specifications" to Dead band and
Position- -proportional dead band.
Added "Model" and "Power specifications" to Manual reset value
and Hysteresis.
Added "Model" and "Power specifications" to Control period.
Added "Model" and "Power specifications" to Heater current
monitor and Heater burnout.
Added "Model" and "Power specifications" to Open/close hyster-
esis.
Added "Model" and "Power specifications" to Control output as-
signment.
Added "Model" and "Power specifications" to PID/ON/OFF.
Added "Model" and "Power specifications" to HBA latch.
Added "Model" and "Power specifications" to Motor Calibration.
Added "Model" and "Power specifications" to Travel Time.
Added "Model" and "Power specifications" to PV dead band.
Modified the diagram in "RS- -232C".
Modified the diagram in "Preparations".
Modified the diagram in "Preparation".
Modified the diagram in "Preparation".
Modified the diagram in "Preparation".
Modified the diagram in "Thermocouple" and "Platinum resis-
tance thermometer".
Modified the diagram in "Current input" and "Voltage input".
Added "Motor calibration error".
Modified "Ratings specifications".
Changed "Type Name" and "Specification" in "Base unit".
Deleted 2) of "At the time the E5AK starts operation" in "Startup
Conditions of SRT".
Deleted 2) of "At the time set point is changed".
Deleted "Imposition Completion Condition of Step Control
Amount".
Modified the diagram in "PID Constant Refreshing Conditions".
Modified the diagram in "Control output".
Changed the title from "Input assignments" to "Event input as-
signments and deleted the flowchart below.
Modified the table contents for "Event input" and added a note
below the table.
Modified the tabel.
Changed the unit from "%" to "%FS" for Alram 1 hysteresis,
Alarm 2 hysteresis, and Alarm 3 hysteresis.
~
or AC/DC24V