JVC HM-HDS1EU Instructions Manual page 45

I
Set the VPS/PDC mode.
Press VPS/PDC to select "ON" or "OFF".
If "VPS/PDC ON" is displayed on the TV screen, VPS/PDC is
set to ON.
If "VPS/PDC OFF" is displayed on the TV screen, VPS/PDC is
set to OFF.
"VPS/PDC Recording" in the right column
J
Set the category.
A Press
w e
to move the
arrow to "CATEGORY",
then press OK. The
category set screen
appears.
B Press
w r e t
to select
the desired category, then
press OK.
C Confirm the arrow is on
"RETURN", then press
OK. The programme
screen resumes.
K
Return to the normal screen.
w r e t
Press to move the arrow to "CONFIRM", then
press OK. "PROGRAMME COMPLETED" appears on the
TV screen for about 5 seconds, then the normal screen
appears.
If "PROGRAMME OVERLAPPED" appears on the TV screen,
see page 46.
L
Engage the recorder's timer mode.
#
Press (TIMER). The recorder turns off automatically and
#
" " appears on the front display panel.
To disengage the timer mode, press
NOTES:
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps D through I, press WEEKLY (number
key "9") for weekly serials or DAILY (number key "8") for daily
serials (Monday – Friday). Either "WEEKLY" or "DAILY"
appears on the TV screen. Pressing the button again makes the
corresponding indication disappear.
During timer recording . . .
. . .it is not possible to disengage the timer mode.
. . .it is not possible to change the recording deck (HDD or
VHS).
PROGRAMME
CHILDREN CLASSICS COMEDY DRAMA
EDUCATIONS MOVIES MUSIC NEWS
RELIGIOUS SERIES SHOPPING SHOW
SPECIAL SPORTS OTHERS UNDECIDED
RETURN
INDEX
SELECT WITH
SELECT OK THEN PRESS [OK]
#
(TIMER) again.
Satellite Receiver Users
To timer-record a satellite broadcast using Express Timer
Programming:
A Perform "Automatic Satellite Programme Recording" on
page 47.
B Perform steps A – L. In step G, press the number key "0"
to change "TV PROG" to "SAT". The front display panel
shows "L2" for the channel position. Then press PR+/– to
enter the channel position for the satellite broadcast. In
step I, you cannot set "VPS/PDC" to "ON".
C Leave the satellite receiver's power on.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
NOTES:
When you use Express Timer Programming, set the start
time (VPS or PDC time) exactly as advertised in the TV
listing. A different time than advertised will result in no
recording.
VPS/PDC recording is also possible when a satellite
receiver or a cable system is connected to AV2 (L-2) IN/
DECODER connector on your recorder.
VPS/PDC recording is also possible via the AV1 (L-1) IN/
OUT connector.
How to check if the station being received transmits a
VPS/PDC signal (VHS deck only)
A Press – –:– – until the channel position appears on the
front display panel.
B Hold down START+ for about 5 seconds.
"VPS/PDC" appears blinking on the front display panel.
If a VPS/PDC signal is detected from the station,
"VPS/PDC" will stop blinking.
If no VPS/PDC signal is detected from the station,
"VPS/PDC" will blink at a slower rate.
C Press – –:– – or START+ again to return to normal display.
45
EN