Ccd White Defect Compensation; Ccd White Defect Compensation Check - Sony DSC-F505 Service Manual

19. CCD White Defect Compensation

Mode STILL
Subject Clear chart
(25 cm from the front of the lens)
(Note1)
Measurement Point Display data of page: 6, address: 55
Measuring Instrument Adjustment remote commander
Adjustment Page 7
Adjustment Address 88 to A3
Data < 7F: OK, Data > 80: NG
Specified value
Note 1: Check that there are no dust, no dirt and no reflection on the clear
chart.
Note 2: Any subject other than the clear chart should not be in the screen.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 5, address: F1, and set data: FF.
3) Select page: F, address: DE, after noting down the data, set
data: 14, and press the PAUSE button of the adjustment remote
commander.
4) Select page: F, address: E3, after noting down the data, set data:
28, and press the PAUSE button.
5) Select page: 6, address: 01, set data: 8B, and press the PAUSE
button.
(The CCD white defect compensation is performed and the
adjustment data is stored in page: 7, address: 88 to A3.)
6) Select page: 6, address: 02, and check that the data changes to
"01".
7) Select page: 6, address: 55, and check the data satisfies specified
value.
Processing after Completing Adjustments:
1) Select page: F, address: DE, set the data noted down at step 3),
and press the PAUSE button.
2) Select page: F, address: E3, set the data noted down at step 4),
and press the PAUSE button.
3) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 5, address: F1, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.

20. CCD White Defect Compensation Check

Mode
Subject
Measurement Point
Measuring Instrument
Specified Value
Note 1: Check that there are no dust, no dirt and no reflection on the clear
chart.
Note 2: Any subject other than the clear chart should not be in the screen.
Note 3: This adjustment should be carried out upon completion of
"CCD White Defect Compensation".
Checking method:
1) Turn the power of the unit OFF and then ON.
2) Wait until the camera picture appear on the screen.
3) Select page: 0, address: 01, and set data: 01.
4) Select page: 5, address: F1, and set data: FF.
5) Select page: F, address: DE, after noting down the data set data:
0A, and press the PAUSE button.
6) Select page: F, address: E3, after noting down the data, set data:
80, and press the PAUSE button.
7) Turn the power of the unit OFF and wait for four seconds.
8) Turn the power of the unit ON.
9) Select page: 0, address: 01, and set data: 01.
10) Select page: 6, address: 55, and check that the data is "00". (If
the data is other than "00", white defect compensation has
errors.)
11) Select page: F, address: E3, set data: A0, and press the PAUSE
button.
12) Select page: 6, address: 01, set data: 87, and press the PAUSE
button.
13) Select page: 6, address: 02, and check that the data changes to
"01".
14) Select page: 6, address: 55, and check that the data is "00". (If
the data is other than "00", black defect compensation has
errors.)
Processing after Completing Adjustments:
1) Select page: F, address: DE, set the data noted down at step 5),
and press the PAUSE button.
2) Select page: F, address: E3, set the data noted down at step 6),
and press the PAUSE button.
3) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 5, address: F1, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
5-34
STILL
Clear chart
(25 cm from the front of the lens)
(Note1)
Display data of page: 6, address: 55
Adjustment remote commander
00