Advertisement
2.2. ENROLLMENT
Refer to the PowerMaster panel's Installer Guide and follow the procedure under the "Zone / Devices" option of the Installer Menu a general
description of which is provided in the following flow chart.
Step 1
Enter the Installer menu
and select the "ZONES /
DEVICES"
ADD NEW DEVICES
02.ZONES/DEVICES
MODIFY DEVICES
Means scroll
and select
Notes:
[1] If the keypad is already enrolled you can configure the keypad parameters via the "Modify Devices" option – see Step 2.
[2] Select the "Device Settings" option and refer to section 2.3 to configure the keypad parameters.
2.3. Configuring the Keypad Parameters
DEVICE SETTINGS
Enter the
following table.
Option
Here you determine which of the two tampers (i.e. battery compartment cover and wall tamper) will be active.
TAMPERS
Optional settings: Disabled (default); Wall only; Battery only.
•
•
Here you determine whether or not the control panel will monitor supervision messages sent by the keypad or not (see
SUPERVISION
Note).
Optional settings: ON (default) or OFF.
Note: Every 5 minutes the keypad performs a communication test session with the control panel (i.e. "Supervision
signal) to check the integrity and quality of the Radio link. If the keypad does not report a supervision signal at
least once within a predefined time window, a "MISSING" trouble alert is initiated. Therefore, if you intend to take
the keypad out of the protected premises you must switch the Supervision OFF to avoid the trouble alert.
•
•
Here you determine whether the keypad will sound the exit and entry beeps, or not, or whether the keypad will sound the
EXIT-ENTRY Beeps
beeps only when the system is armed AWAY and not when it is armed HOME.
Optional settings: ON; OFF (default) and OFF @ Home.
•
•
BUTTON ( )
Here you select the function of the (AUX) button
Not used: No function assigned to AUX button.
Stop Beeps: Pressing the AUX button will cause the control panel and other devices in the system (such as keypads,
sirens etc.) to stop beeping (for example during exit or entry delays).
Skip exit delay: Pressing the AUX button will immediately stop the exit delay.
PGM: Pressing the AUX button will activate the PGM output. The functions of the PGM output is configured at the
corresponding sections of the control panel's Installer Guide (see "OUTPUTS" menu) and User Guide (see
"SCHEDULER " menu).
Optional settings:
2.4 Enrollment of Proximity Tags
The built-in proximity tag reader of the KP-141PG2 can be also used
to enroll proximity tags into the PowerMaster panel via the keypad as
described in the corresponding section of the control panel's User or
Installer Guide.
When the panel display prompts you to enroll the tag ("ENROLL NOW"
is displayed), perform the following:
2
Step 2
Select "ADD NEW
Enroll the device or Enter
DEVICE" Option
See Note [1]
ENROLL NOW or
ENTR ID:XXX-XXXX
menu and follow the configuration instructions for the KP-140 PG2/KP-141 PG2 keypad as described in the
Not Used (default)
Step 3
Select the desired Zone
the device ID
Z20: Keypad
ID No. 370-XXXX
Configuration Instructions
. Four options are offered:
;
Stop Beeps; Skip exit delay; and PGM.
a) Press the AWAY button (
the AWAY button begins to blink.
b) Present the proximity tag to the KP-141 PG2 keypad within the
timeout period. If the enrollment is successful the display reads
"DEVICE ENROLLED" and then shows the device details.
Step 4
Step 5
Configure Location,
Number
Zone Type &
Chime Parameters
Z20.LOCATION
Z20.ZONE TYPE
Z20.SET CHIME
Z20.DEV SETTINGS
) on the KP-141 PG2 keypad -
Step 6
Configure
the
Keypad
See Note
[2]
D-303015
Advertisement
