Siemens RDG100 Documentation page 48

P52 Fan operation
P53 Fan speed
P54 Fan overrun time
(only when electr. heater is used)
P55 Switching point fan speed high
P55 ECM fan max. output
P56 Switching point fan speed med
P56 ECM fan min. output
P57 Switching point fan speed low
P57 ECM: Switching point fan
P58 Fan start booster
P59 Fan minimum on time (dwell time)
P60 Fan kick in Comfort (time until next kick)
P61 Fan kick in E-saving mode (time until next kick)
P62 Clean filter reminder run-time
P65 Protection heating setpoint
P66 Protection cooling setpoint
P67 Fan start delay in 2P control
P68 Prolong Comfort period
P69 Temporary setpoint Comfort
(see also Comfort setpoint P08)
P70 Infrared receiver
P71 Reload factory settings
Name
Diagnostics & test
d01 Application type
d02 X1 status
d03 X2 status
d04 D1 status
d05 Test mode for checking the Y1/Y2
actuator direction
(press left button to escape)
d06 Test mode for checking the Y3/Y4
actuator direction
(press left button to escape)
48 / 60
Siemens
Building Technologies
Tel: 01823 665660
Heronhill - for all your Siemens requirements
1
3-speed
60 sec
100%
ECM: 80%
65%
ECM: 30%
10%
ECM:10%
ON
2 min
0
OFF
Off (0)
8 °C
OFF
0 s
OFF
OFF
ON
OFF
Factory setting
Diagnostics
Diagnostics
Diagnostics
Diagnostics
---
---
Parameter available
Parameter not available
RDG100.../RDG110.../RDG140.../RDG160... Basic Documentation
Functions
www.heronhill.co.uk
0 = Disabled
1 = Enabled
2 = Heating only
3 = Cooling only
1 = 1-speed
2 = 3-speed
0 ... 360 sec
80..100%
ECM: fan min....100%
30..75%
ECM: 0%...fan max.
1..15%
ECM: 0..100%
ON: enabled
OFF: disabled
1 ... 6 min
0...89 min, OFF(90 min)
0...359 min, OFF(360 min )
Off, 100 ... 9900 hours
OFF, 5 ... W Cool Prot;
(W Cool Prot = 40 °C max)
OFF, W Heat Prot ... 40;
(W Heat Prot = 5 °C min.)
0.. 180 s
OFF; 15 ... 360 min
OFF = Disabled
ON = Enable
OFF = Disabled
ON = Enabled
OFF = Disabled
ON = Reload start
Range
0 = (No application)
1 = 2-pipe
2 = 2-pipe with electric heater
3 = 2-pipe with radiator
4 = 4-pipe
5 = 2 stage heat or cool
6 = 4-pipe with electric heater
0 = Not activated (for DI)
1 = activated (DI)
0...49 °C = cur. temp. value (for AI)
00 = HC input short
100 = HC input open
0 = Not activated (for DI)
1 = activated (DI)
0...49 °C = cur. temp. value (for AI)
00 = HC input short
100 = HC input open
0 = Not activated (for DI)
1 = activated (DI)
00 = HC input short
100 = HC input open
"---" = no signal on outputs Y1 and Y2
OPE = output Y1 forced open
CLO = output Y2 forced closing
"---" = no signal on outputs Y3 and Y4
OPE = output Y3 forced open
CLO = output Y4 forced closing
CE1P3076.en
28 May 2009
Fax: 01823 665807