Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
Specification Front Panel Function Control Description Circuit Description Adjustment Procedure Troubleshooting Flow Chart Recommended Spare Parts List Exploded Diagram and Exploded Parts List Block Diagram 10. Schematic Diagrams 11. PCB Layout Diagrams ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
(1) Since front polarizer is easily damaged, pay attention not to scratch it. (2) Be sure to turn off power supply when connecting or disconnecting input connector. (3) Wipe off water drops immediately. Long contact with water may cause discoloration or spots. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 5
(14) The LCD module is designed so that the CCFL in it is supplied by a Limited Current Circuit (IEC60950 or UL1950). Do not connect the CCFL to a Hazardous Voltage Circuit ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 6
Take out the monitor by grasping the LCD panel. That may cause “ MURA“. Place the monitor on a clean & soft foam pad . Place the monitor on foreign objects . That could scratch the surface of panel ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
½ cycle of AC power is randomly missing at nominal input. The power supply shall not produce audible noise that would be Power Supply Acoustics detectable by the user. Audible shall defined to be in VX2245wm-1 ViewSonic Corporation Confidential - Do Not Copy...
(Still at the center), And the OSD 720 x 400 @ 85 Hz, 37.9 KHz will be 640x350/640x400/720x400 (primary = 720x400). 720 x 480 @ 60 Hz, 31.5 KHz For Analog sync, the image vertical size image will VX2245wm-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 12
*3. The image quality of 85Hz mode might be worse than 75Hz. Primary Presets 1680x1050 @ 60Hz User Presets Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration VX2245wm-1 ViewSonic Corporation Confidential - Do Not Copy...
3.5mm stereo cable / 1.8m length Cable type / length SPEAKERS STAY OFF WHEN THE REST OF THE MONITOR Audio DPMS IS IN POWER SAVING * No any sympathetic or abnormal noise allowed. VX2245wm-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 16
Preset Color Temperature Each color preset shall be adjustable. Red, Green, and Blue shall Adjustability be individually controlled. * Any gray level and Contrast/Brightness should not get reddish, greenish or bluish. VX2245wm-1 ViewSonic Corporation Confidential - Do Not Copy...
Displays the Main Also a shortcut to display Menu or exits the the Contrast adjustment control screen and control screen ( ) / saves adjustments. OptiColor ( ) ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 18
• If necessary, make small adjustments using H. POSITION and V. POSITION until the screen image is completely visible. (The black border around the edge of the screen should barely touch the illuminated “active area” of the LCD display.) ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 19
Enabling this setting allows the LCD display to more accurately display colors the way they were originally intended. Enabling the sRGB setting will cause the Contrast and Brightness adjustments to be disabled. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 20
Preset Timing Mode, colors return to the 6500K factory preset. Information displays the timing mode (video signal input) coming from the graphics card in the computer, the LCD model number, the serial number, and the ViewSonic website URL. See your graphics card’s user guide for ®...
Page 21
Scenery optimized for displaying outdoor scenery images. Vivid optimized for color luster and sharpness. These 7 presets are carefully chosen by Viewsonic, but may not suit all users' tastes. In that case, the user can either return to the Standard setting and manually adjust the brightness and contrast as desired.
Page 22
OSD Background allows the user to turn the OSD background On or Off. Memory Recall returns the adjustments back to factory settings if the display is operating in a factory Preset Timing Mode listed in the Specifications of this manual. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Physical Description Please refer to the following illustrations to identify the components of the ViewDock. Front View Rear view ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
3. After completing installation, connect the ViewDock to your PC's USB port. The card reader is now operational. 4. Each slot of the card reader will be recognized as a Removable Disk and the icon will be shown in "My Computer." ViewSonic Corporation VX2245wm-1...
Page 25
4. Wait for a few seconds for the iTunes software to launch. 5. Play your favorite song with iTunes software (for all iPod models) or play music from iPod directly (excluding iPod shuffle.) ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 26
4. In order to obtain the optimum listening environment, please adjust the volume of stereo speakers in the monitor head via the monitor OSD menu to match and balance the subwoofer volume. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
TSMC 0.18um e-FLASH process. Here we use the package of PLCC44/LQFP48 if we would like to have a discrete MCU controller or we make a multi-chip package with our LCD monitor controller to form one chip package to save the cost of package and PCB material. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Test Pattern: Checkered Pattern Every One Pixel (50%Green & 50%Blue) Inspection Item: Flicker, Mura 6. Window BG Test Signal: 1280*1024@60Hz Test Pattern: Window standard pattern Inspection Item: Line Defect, Function Defect & Mura ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 35
Inspection Item: Particle, Line Defect, Power, Image Remain & Mura 10. Black Box Test Signal: 1280*1024@60Hz Test Pattern: Window standard pattern Inspection Item: Bright Dot, Line Defect & Power 11. RED Test Signal: 1280*1024@60Hz Test Pattern: ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 36
Full Screen 50% Red Figure 4 Green Full Screen 50% Green Figure 5 Blue Full Screen 50% Blue Figure6 White Full Screen White Figure7 Black_Tile Black Tile Under White Background Figure 8 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 38
If the O.S. was Win2000 or Win XP please have to install Fig1 PORT95NT.exe In order to ensure can execute ISP program, please set BIOS in PC or Notebook as Fig 2 Fig 2 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 39
2.2 After extracting the zip file, the total files list as Fig 2.2, and double click the file of setup.exe to install. Fig 2.2 2.3 Press “Next" button to continue., see Fig 2.3 Fig 2.3 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 40
2.4 Keep default setting or press “Change" button for selecting the path that you want , and then press“Next"button to continue, see Fig 2.4. Fig 2.4 2.5 Press “Install" button to continue, see Fig 2.5 Fig 2.5 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 41
2.6 The Installer Information shows package warning, press “Ignore" button to continue, see Fig 2.6. Fig 2.6 2.7 Installation has finished, press “Finish" button, see Fig 2.7. Fig 2.7 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 42
3.1 After installation, we could find the shortcut in the setting path or the program bar (default setting), see Fig 3.1 Fig 3.1 2.2 Security file is a key to use ISP function, press “確定" button, see Fig 3.2. Fig 3.2 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 43
3.3 The warning is used to remind user of that different CPU rate may cause ISP function fail(it is limited by IIC protocol), press “確定" button, see Fig 3.3. Fig 3.3 security code. Adjusting bar to decrease speed of IIC bus, see Fig 3.4. 2.4 Press“Create Security File" button to key in Fig 3.4 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 44
Command No of security code, see Fig 3.5, and different security code between hardware ISP and software ISP. The security code of software ISP is set by user while coding, but the security code of hardware ISP is set by Myson Century. Fig 3.5 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 45
ISP, it needs Fig 3.6 shows the setting for security code of Command No, and key in command sequentially 94, 94, AC, CA, Fig 3.6 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 46
Command No, and key in command sequentially 7C, 4C, 77. The Command No and command must be set by user while coding. About the detail of setting, please refer to Section 6 Boot code of ISP. Fig 3.7 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 47
4.3 CRC (cyclic redundancy check): the host can check CRC register's result instead of reading every byte in flash. The message of Check MCU CRC OK means that the Host verify ok for the progress of program. Fig 4.1 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 48
5.1 Only software ISP could read the MCU content, it is according to program the boot code while coding. The limitation is used for the security of customer's code. Select “Read Target" item, and press“RUN" button, the MCU content will show as Fig 5.1. Fig 5.1 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 49
5.2 If user uses hardware ISP to read MCU content, it shows as Fig 5.2. Fig 5.2 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 50
6 Re-entry the ISP Mode MCU' button and enter ISP mode again, you refer the message as below: When you could not select or click `Reset ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 51
(1)Disable the ‘Enter ISP Mode’ option to avoid the error message display. (2)If you using the MTV312M64 or before MCU serials, the MCU will always in ‘ISP Mode’even programming fail or erase MCU that instead of select or press ‘Reset MCU’. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 52
(a) Clear watchdog to prevent reset during ISP period (b) Disable all interrupt to prevent CPU wake-up (c) Write ISP slave address (d) Write 93h to ISP enable address to enable ISP (e) Enter 8051 idle mode ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 53
7.4 The followings show the relationship between the code and the security code ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 54
8. ISP Adaptor Schematic 9. Adaptor Linking ISP Adaptor Connect with The Monitor Set PC/HOST Printer Cable 25Pins to 25Pins Connect with VGA Cable 15Pins to 15Pins ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 55
1.3 Put the cushion into the carton then place the monitor on the cushion. (Figure 3) 1.4 Join the cushions to the monitor then place all the accessories into the carton. As last, close the carton and seal it with tape. (Figure 4) Figure 3 Figure 4 ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 56
1 Separate Stand Assy 1 Remove Stand Cover Step 1 : Remove the Stand Covers. Step 2 : Loose and remove 6 screws Step4 : Remove the Stand Assy Step 5 : Completed. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 57
Separate Bezel hooks to take Bezel and Rear Cover apart. Step 1 : Loose and remove 3 screws. Step 2 : Separate Bezel hooks to take Bezel and Rear Cover apart. Step 3 : Remove Rear Cover. Step 4 : Completed. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 58
Remove FFC from OSD Board. Step 2 : Lift up LCD module and remove bezel. Step 3 : Remove 4 pieces of Backlight wires. Step 4 : Loose and remove 4 screws. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 59
Loose and remove 4 screws. Step 7 : Remove the PCBA Cover 3.2 Remove Power Board and AD Board Step 1 : Loose and remove 4 screws. Step 2 : Remove Lips Board ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 60
Step 3 : Remove 2 pieces of FFCs. Step 4 : Remove the FFC. Step 5 : Loose and remove 4 screws. Step 6 : Remove AD PCBA. Step7 : Completed. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 61
And fasten 4 fixed screws. Step 2 : Fasten 4 fixed screws. Step 3 : Insert FFC. Step 4 : Insert 2 pieces of FFCs . Step 5 : Insert new Lips Board. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 62
Step 6 : Fasten 4 fixed screws. Step 7 :Completed. 5. Remove OSD Board Step 1 : Separate both Audio Cable. Step 2 : Take OSD Board apart. Step 3: Completed. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 63
Insert Audio cable to connectors of New OSD Board. Step 3: Completed. 7. Add Cover to AD PCB Heatsink Step 1 : Join the PCB Cover. Step 2 : Fasten 4 fixed screws. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Display Bright Dot Dark Dot Backlight Light Leakage Mura Panel Change Check Panel Image Sticking Brightness spot Particle Dot Defect Image Remain Group Bright Dots Others Cosmetics Defect TEST Next Step Completed ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 67
Check Panel Panel Change Beat Display Shut Down AD/B Change Display Wave Check PCBA Power/B Change CNT/B Change Panel Change Check Panel No Backlight Check Adapter Adapter Change TEST Next Step Completed ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 68
Adapter Change No signal AD/B Change Check PCBA CNT/B Change R.G.B Display Abnormal VGA cable Change Check Wire Gray Scale DVI cable Change Display Panel Change Check Panel Abnormal TEST Next Step Completed ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 69
Vertical Check Panel Panel Change Band Defect Horizontal Band Defect Power Saving Display AD/B Change Check PCBA Abnormal AD/B Change Power/B Change Peculiar Smell Check PCBA Inverter/B Change TEST Next Step Completed ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 70
LED Off Check PCBA Abnormal Inverter/B Change LED Dark OSD/B Change LED Abnormal OSD Cable Change Check Wire LED Loss DC Power CNT Cable Change LED Flicker Adapter Change TEST Next Step Completed ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 71
CNT/B Change Abnormal Power/B Change Loud Check PCBA Inverter/B Change Abnormal OSD/B Change Check Wire No Voice OSD Cable Change Loudspeaker L/R Same Check Loudspeaker Change Volume Loudspeaker Next Step TEST Noise Completed ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 72
Panel Change AD/B Change Display Flicker Check PCBA (tapping ) CNT/B Change Check Panel Panel Change DVI Signal Check PCB AD/B Change Display Abnormal EDID Update Check EDID Code TEST Next Step Completed ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Page 73
Use OSD Color Menu to adjust color setting. Dark area distorted Use OSD Color Menu to adjust color setting. White color is not white Use OSD Color Menu to adjust color setting. ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions. ViewSonic Corporation...
Page 75
Cushion, A220Z1-H08, EPS, WHITE, 260 mmx195 mmx590 mm, Li Ta NingBo Ming- 78-D013545 P-00008140 Chan_EPS, EPS foam(Right), Green II Decoration Assy, A220Z1-H08, ABS, Siliver(877C), ViewSonic Display Limited, VSC P/N C- 40-D013544 M-00008031 00006107, Green I Function Cable, E87647 30V, 1Pins-1Pins, ViewSonic Display Limited, VSC P/N C-00006107,...
9. Block Diagram Speaker OSD Key Pad / Audio Out 3.3V DVI-D Digital Video Main Board LCD Module D-sub Analog Video Signal DC-12V DC-5V LIPS AC Power Backlight Audio In ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...
Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) ViewSonic Corporation VX2245wm-1 Confidential - Do Not Copy...