Page 1 FD8167-(T) FD8367-V/TV Fixed Dome Network Camera User’s Manual 2MP • 30M IR • Smart IR • Smart Stream • 3DNR • P-iris 2MP • 30M IR • IP66 • Smart IR • Smart Stream• 3DNR • P-iris Rev. 1.0...
Page 2: Table Of Contents
Applications > Motion detection��120 Applications > DI and DO ��123 Applications > Tampering detection ��123 Applications > Audio detection ��124 Applications > VADP (VIVOTEK Application Development Platform) ��126 PIR ��128 Recording > Recording settings ��129 Local storage > SD card management ��134 Local storage >...
Page 3 VIVOTEK Appendix �� URL Commands for the Network Camera �� 138 Technical Specifications �� 221 Technology License Notice �� 222 Electromagnetic Compatibility (EMC) �� 223 User's Manual - 3...
Page 4: Overview
30 fps, the FD8167 is an all-in-one indoor camera capable of capturing high quality and high resolution video up to 2 Megapixel, even in low light environment� Providing such a polished image quality, FD8167 is also designed with VIVOTEK Smart Stream, 3DNR to save notable bandwidth for users�...
Page 5: Read Before Use
Commands of the Network Camera section serves as a helpful reference to customizing existing homepages or integrating with the current web server� Package Contents ■ FD8167, FD8167-T, FD8367-V, FD8367-T ■ Alignment sticker ■ Stardriver / Desiccant bag / Double-sided tape (8367) ■...
Page 6 VIVOTEK DI/DO Diagram Please refer to the following illustration for the connection method� Camera Power Camera Power Switch Switch Input Input Max. Output Output BJT transistor BJT transistor Relay Relay NOTE: The maximum output load from the Digital Output pins is 50mA�...
Page 7 VIVOTEK Hardware Reset Reset Button The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems remain after reset, restore the factory settings and install again�...
Page 8: Installation (Fd8167)
VIVOTEK Installation (FD8167) 1� Jot down the MAC address of the camera for later reference� FD8167 0002D10766AD 2� Press the release button on the side to remove the top cover� 3� Attach the alignment sticker to wall, and drill holes on it� Fasten 3 screws half-way into the wall�...
Page 9 VIVOTEK Consider the effective range and the shooting angles of the PIR when determining the mounting position of the camera� 121° 77.3° 4� You may drill a cabling hole for routing the cables� You can then hang the camera to the screws by passing them through the key slot holes�...
Page 10 VIVOTEK 5� If preferred, connect the DI/DO wires to the terminal blocks� Name Audio_out- Audio_out+ 9 10 12V DC-_IN 10 12V DC+_IN 6� Turn the lens moudle around for the best shooting angle� 350° 60° 350° 10 - User's Manual...
Page 11 7. Assigning an IP Address 7-1� Install the "Installation Wizard 2�" 7-2� The program will search for VIVOTEK Video Receivers, Video Servers or Network Cameras on the same LAN� 7-3� Double-click on the camera's MAC address to open a browser management session with the camera�...
Page 12: Installation (Fd8367)
VIVOTEK Installation (FD8367) 1� Jot down the MAC address of the camera for later reference� FD8167 0002D10766AD 2� Use the included stardriver to loosen the anti-tamper screws, and open the dome cover� 12 - User's Manual...
Page 13 VIVOTEK 3� Remove the waterproof connectors� 4� Pass cables through the rubber seal and cable gland� 5� Strip part of the cable� 6� Use a crimping tool to attach the wires to an RJ45 connector� o: white/orange stripe O: orange solid...
Page 14 VIVOTEK 7� If preferred, connect the DI/DO wires to the terminal block� Name Audio_MIC_N EXT_MIC_P Audio_out- Audio_out+ 9 10 12V DC-_IN 10 12V DC+_IN 8� Attach the alignment sticker to wall, and drill holes on it� You may drill a cabling hole for routing the cables�...
Page 15 VIVOTEK 9� Fasten 3 screws half-way into the wall� You can then hang the camera to the screws by passing them through the key slot holes� User's Manual - 15...
Page 16 VIVOTEK 10� If you prefer using a conduit for routing cables, you can attach the side bushing to the cabling indent of the camera� You can use two screws to secure the side bushing� 3/4" 11� Turn the lens moudle around for the best shooting angle�...
Page 17 12. Assigning an IP Address 12-1� Install the "Installation Wizard 2�" 12-2� The program will search for VIVOTEK Video Receivers, Video Servers or Network Cameras on the same LAN� 12-3� Double-click on the camera's MAC address to open a browser management session with the camera�...
Page 18 VIVOTEK 13� Attach the top cover and secure the anti-tamper screws� NOTE: For the outdoor models: You will find a desiccant bag attached to the dome cover� Replace the desiccant bag included in the camera with the one in the accessory bag�...
Page 19: Network Deployment
VIVOTEK Network Deployment General Connection (without PoE) Non-PoE Switch DC 12V±10% Ethernet 1� Connect RJ45 Ethernet cable to a switch� 2� Connect the AC cables from the terminal block as an alternate power source� The IO cables are user-supplied� Power over Ethernet (PoE)
Page 20 VIVOTEK When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch� PoE Power Injector (optional) Non-PoE Switch 20 - User's Manual...
Page 21 VIVOTEK Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below� 1� Connect your Network Camera behind a router, the Internet environment is illustrated below�...
Page 22 For more information with network configuration options (such as that of streaming ports), please refer to Configuration > Network Settings. VIVOTEK also provides the automatic port forwarding feature as an NAT traversal function with the precondition that your router must support the UPnP port forwarding feature�...
Page 23: Software Installation
After your network environment is analyzed, please click Next to continue the program� 3� The program will search for all VIVOTEK network devices on the same LAN� 4� After a brief search, the installer window will prompt� Click on the MAC and model name that matches the one printed on the product label�...
Page 24: Ready To Use
VIVOTEK Ready to Use 1� A browser session with the Network Camera should prompt as shown below� 2� You should be able to see live video from your camera� You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras� For its installation details, please refer to its related documents�...
Page 25: Accessing The Network Camera
3� The live video will be displayed in your web browser� 4. If it is the first time installing the VIVOTEK network camera, an information bar will prompt as shown below� Follow the instructions to install the required plug-in on your computer�...
Page 26 VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 90�...
Page 27 VIVOTEK IMPORTANT: • Currently the Network Camera utilizes a 32-bit ActiveX plugin. You CAN NOT open a management/view session with the camera using a 64-bit IE browser. • If you encounter this problem, try execute the Iexplore.exe program from C:\Windows\ SysWOW64.
Page 28: Using Rtsp Players
VIVOTEK Using RTSP Players To view the streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player VLC media player mpegable Player 1� Launch the RTSP player� pvPlayer 2� Choose File > Open URL� A URL dialog box will pop up�...
Page 29: Using 3Gpp-Compatible Mobile Devices
VIVOTEK Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet� For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 19�...
Page 30: Using Vivotek Recording Software
Network Camera to the Channel list� For detailed information about how to use the recording software, please refer to the user’s manual of the software or download it from http://www.vivotek.com� 30 - User's Manual...
Page 31: Main Page
VIVOTEK Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC� Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� Resize Buttons VIVOTEK INC. Host Name...
Page 32: Client Settings
VIVOTEK Configuration Area Client Settings: Click this button to access the client setting page. For more information, please refer to Client Settings on page 36� Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a password be applied to the Network Camera so that only the administrator can configure the Network Camera.
Page 33 Quick Time player only supports playback of H�264 stream, and not the MJPEG stream� In terms of audio codec, Quick Time only supports AAC� Since this camera supports G�711 codec, audio is not available on Quick Time� The VLC player supports H�264/MPEG-4/MJPEG, and all audio codecs supported by VIVOTEK’s cam- eras� User's Manual - 33...
Page 34 VIVOTEK Video and Audio Control Buttons: Depending on the Network Camera model and Network Camera configuration, some buttons may not be available. Snapshot: Click this button to capture and save still images. The captured images will be displayed in a pop-up window� Right-click the image and choose Save Picture As to save it in JPEG (*�jpg) or BMP (*�bmp) format�...
Page 35 VIVOTEK ■ The following window is displayed when the video mode is set to MJPEG: Video Title Time 2014/09/25 17:08:56 Video (HTTP-V) Title and Time Video 17:08:56 2014/09/25 Video Control Buttons Video Title: The video title can be configured. For more information, please refer to Media > Image on page 55�...
Page 36: Client Settings
VIVOTEK Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer� When completed with the settings on this page, click Save on the page bottom to enable the settings� H.264 Media Options H.264 Media Options...
Page 37: Mp4 Saving Options
VIVOTEK Two Way Audio Select one of the checkboxes to configure the two way audio into the half- or full-duplex mode. MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page.
Page 38: Joystick Settings
VIVOTEK Joystick Settings Enable Joystick Connect to the USB plug of the joystick to a USB port on your management computer� Once a USB joystick is connected, the related joystick configuration will be available on the Client settings window� The joystick should work properly without installing any other driver or software�...
Page 39 VIVOTEK Buttons Configuration In the Joystick Settings window, you can use the combinations of pull-down menus, Actions and Button number, to assign joystick buttons with different functions� The number of buttons may differ from the joystick you attached� Please follow the steps below to configure your joystick buttons: 1.
Page 40 VIVOTEK NOTE: • If you want to assign Preset actions to your joystick, the PTZ preset locations should be configured in advance� • If your joystick is not working properly, it may need to be calibrated� Click the Calibrate button to open the Game Controllers window located in Microsoft Windows control panel and follow the instructions for trouble shooting�...
Page 41: Configuration
VIVOTEK Configuration Click Configuration on the main page to enter the camera setting pages� Note that only Administrators can access the configuration page� Please refer to page 90 Security > User Account for how to configure access rights for different users.
Page 42: System > General Settings
VIVOTEK System > General settings This section explains how to configure the basic settings for the Network Camera, such as the host name and system time. It is composed of the following two columns: System and System Time� System Host name: Enter a desired name for the Network Camera. The text will be displayed at the top of the main page�...
Page 43: System > Homepage Layout
Theme Options (the second tab on this page)� The settings will be displayed automatically in this Preview field. The following shows the homepage using the default settings: ■ Hide Powered by VIVOTEK: If you check this item, it will be removed from the homepage. Logo graph Here you can change the logo that is placed at the top of your homepage�...
Page 44 VIVOTEK Theme Options Here you can change the color of your homepage layout� There are three types of preset patterns for you to choose from� The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings�...
Page 45 VIVOTEK ■ Follow the steps below to set up the customed homepage: 1� Click Custom on the left column� 2. Click the field where you want to change the color on the right column. Color Selector Custom Pattern 3� The palette window will pop up as shown below�...
Page 46: System > Logs
VIVOTEK System > Logs This section explains how to configure the Network Camera to send the system log to a remote server as backup� Log server settings Follow the steps below to set up the remote log: 1� Select Enable remote log�...
Page 47: System > Parameters
VIVOTEK Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in a chronological order� The access log is stored in the Network Camera’s buffer area and will be overwritten when reaching a certain limit�...
Page 48: System > Maintenance
Note: Do not power off the Network Camera during the upgrade! Follow the steps below to upgrade the firmware: 1. Download the latest firmware file from the VIVOTEK website. The file is in .pkg file format. 2� Click Browse… and specify the firmware file.
Page 49 VIVOTEK General settings > Restore This feature allows you to restore the Network Camera to factory default settings� Network: Select this option to retain the Network Type settings (please refer to Network Type on page 73)� Daylight Saving Time: Select this option to retain the Daylight Saving Time settings (please refer to Import/Export files below on this page).
Page 50 VIVOTEK ® 3. Open the file with Microsoft Notepad and locate your time zone; set the start and end time of DST� When completed, save the file. In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m.
Page 51 VIVOTEK The following message is displayed when attempting to upload an incorrect file format. Export language file: Click to export language strings. VIVOTEK provides nine languages: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文, and 繁體中文 � Update custom language file: Click Browse… and specify your own custom language file to upload.
Page 52: Media > Image
VIVOTEK Media > Image This section explains how to configure the image settings of the Network Camera� It is composed of the following four columns: General settings, Picture settings, Exposure, and Privacy mask� General settings Video title Show_timestamp_and video_title_in_video_and_snapshots: Enter a name that will be displayed on the title bar of the live video as the picture shown below�...
Page 53 VIVOTEK Day/Night Settings Switch to B/W in night mode Select this to enable the Network Camera to automatically switch to Black/White during night mode� Turn on external IR illuminator in night mode Select this to turn on an external IR illuminator (connected via Digital Output lines) when the camera detects low light condition and enters the night mode�...
Page 54 VIVOTEK Tips: If there is an object in close proximity, the IR lights reflected back from it can mislead the Smart IR’s calculation of light level� To solve this issue, you can place an “Exposure Exclude” window on an unavoidable object in the Exposure setting window�...
Page 55: Image Settings
VIVOTEK Image settings On this page, you can tune the White balance, Image adjustment and WDR enhanced � Sensor Setting 1: For normal situations Sensor Setting 2: For special situations White balance: Adjust the value for the best color temperature.
Page 56 VIVOTEK Noise reduction ■ Enable 3D noise reduction: Check to enable noise reduction in order to reduce noises and flickers in image. This applies to the onboard 3D Noise Reduction feature. Use the pull-down menu to adjust the reduction strength� Note that applying this function to the video channel will consume system computing power�...
Page 57 VIVOTEK Measurement Window: This function allows users to configure measurement window(s) for low light compesation� ■ Full view: Calculate the full range of view and offer appropriate light compesation� ■ Custom: This option allows you to manually add specific windows as measuring areas. The measuring window refers to “weighed window“...
Page 58 VIVOTEK You can click Restore to recall the original settings without incorporating the changes� When completed with the settings on this page, click Save to enable the settings� If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open the Profile of exposure settings page as shown below.
Page 59 VIVOTEK Focus (This window is available on FD8167-T and FD8367-T) The camera comes with a motorized vari-focal lens, and therefore a smart focus function panel is provided to facilitate zoom and focus configuration. Focus window ■ Zoom: If you need to zoom in to a field of view, click and drag the pointer to the right to zoom in.
Page 60 VIVOTEK ■ Full-range scan: If selected, the auto focus scan will be performed throughout the complete range of focus� The full-range scan takes a longer time to complete� A full-range scan usually takes approximately 3 minutes or longer� ■ Fully-open Iris: By default, this checkbox is selected for performing an auto scan and should provide an optimal scan result�...
Page 61 VIVOTEK Privacy mask Click Privacy Mask to open the settings page� On this page, you can block out sensitive zones to address privacy concerns� 2010/12/09 17:08:56 2010/12/09 17:08:56 ■ To set the privacy mask windows, follow the steps below: 1� Click New to add a new window�...
Page 62: Media > Video
VIVOTEK Media > Video Stream settings This Network Camera supports multiple streams with frame size ranging from 176 x 144 to 1920 x 1080 pixels� The definition of multiple streams: ■ Stream 1: Users can define the "Region of Interest" (viewing region) and the "Output Frame Size"...
Page 63 VIVOTEK Click Viewing Window to open the viewing region settings page. On this page, you can configure the Region of Interest and the Output Frame Size for streams 1� For example, you can crop only a portion of the image that is of your interest, and thus save the bandwidth needed to transmit the video stream�...
Page 64: Media > Video
VIVOTEK Media > Video NOTE: ► All the items in the “Region of Interest” should not be larger than the “Output Frame Size“ (current maximum resolution)� ■ The parameters of the multiple streams: Region of Interest Output frame size Stream 1...
Page 65 VIVOTEK Click the stream item to display the detailed information� The maximum frame size will follow your settings in the above Viewing Window sections� This Network Camera offers real-time H�264 and MJPEG compression standards (Dual Codec) for real-time viewing� If H.264...
Page 66 VIVOTEK The frame rate will decrease if you select a higher resolution� ■ Intra frame period Determine how often to plant an I frame� The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption� Select the intra frame period from the following durations: 1/4 second, 1/2 second, 1 second, 2 seconds, 3 seconds, and 4 seconds�...
Page 67 VIVOTEK • Smart stream: Smart stream can effectively reduce the video packet size while maintaining good video quality in the selected areas of your interest. When properly configured, Smart stream can reduce the stream size to half or even lower�...
Page 68 VIVOTEK • Mode: - Auto: When set to Auto, only the moving objects and the areas around them will be displayed with the Foreground quality� The rest of the screen will be displayed with the Background (lower) quality� - Manual: When selected, the Manual window setting option will be displayed. Click on it to display the setting window�...
Page 69 VIVOTEK - Hybrid: When enabled, moving objects in the Background areas will also be displayed using the Foreground (better) quality� Note the following with the Smart stream setting: 1� When using the “Auto” or “Hybrid” modes, up to 30 moving objects can be displayed using the Foreground quality�...
Page 70 VIVOTEK JPEG mode is selected, the Network Camera sends consecutive JPEG images to the client, producing a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage� Because the media contents are a combination of JPEG images, no audio data is transmitted to the client�...
Page 71: Audio Settings
VIVOTEK Media > Audio Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients. Note that if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page.
Page 72: Network > General Settings
Use fixed IP address: Select this option to manually assign a static IP address to the Network Camera� 1� You can make use of VIVOTEK Installation Wizard 2 on the software CD to easily set up the Network Camera on LAN� Please refer to Software Installation on page 23 for details�...
Page 73 VIVOTEK Primary DNS: The primary domain name server that translates hostnames into IP addresses. Secondary DNS: Secondary domain name server that backups the Primary DNS. Primary WINS server: The primary WINS server that maintains the database of computer names and IP addresses�...
Page 74 VIVOTEK NOTE: NOTE ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera� ► If UPnP is not supported by your router, you will see the following message: Error: Router does not support UPnP port forwarding.
Page 75 VIVOTEK 4� In the Networking Services dialog box, select Universal Plug and Play and click OK� 5� Click Next in the following window� 6� Click Finish� UPnP is enabled� ► How does UPnP work? UPnP networking technology provides automatic IP configuration and dynamic discovery of devices added to a network�...
Page 76 VIVOTEK Enable IPv6 Select this option and click Save to enable IPv6 settings� Please note that this only works if your network environment and hardware equipment support ® IPv6� The browser should be Microsoft Internet Explorer 6�5, Mozilla Firefox 3�0 or above�...
Page 77 VIVOTEK Please follow the steps below to link to an IPv6 address: 1� Open your web browser� 2� Enter the link-global or link-local IPv6 address in the address bar of your web browser� 3. The format should be: http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/ IPv6 address 4�...
Page 78 VIVOTEK Port HTTPS port: By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535� Two way audio port: By default, the two way audio port is set to 5060. Also, it can also be assigned to another port number between 1025 and 65535�...
Page 79 To stop talking, click again� FTP port: The FTP server allows the user to save recorded video clips. You can utilize VIVOTEK's Installation Wizard 2 to upgrade the firmware via FTP server. By default, the FTP port is set to 21.
Page 80: Network > Streaming Protocols
VIVOTEK Network > Streaming protocols HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 90 for details. Authentication: Depending on your network security requirements, the Network Camera provides two types of security settings for an HTTP transaction: basic and digest.
Page 81 VIVOTEK URL command -- http://<ip address>:<http port>/<access name for stream 1, 2, or 3> For example, when the Access name for stream 2 is set to video2�mjpg: 1� Launch Mozilla Firefox or Netscape� 2� Type the above URL command in the address bar� Press Enter�...
Page 82 VIVOTEK Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. basic authentication is selected, the password is sent in plain text format, but there can be potential risks of it being intercepted�...
Page 83 VIVOTEK Multicast settings for stream 1, 2, and 3: Click the items to display the detailed configuration information� Select the Always multicast option to enable multicast for stream 1 or 2� Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other hand, sends a stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address�...
Page 84 IP address, to have a fixed host and domain name. Express link Express Link is a free service provided by VIVOTEK server, which allows users to register a domain name for a network device� One URL can only be mapped to one MAC address�...
Page 85 DDNS: Dynamic domain name service Enable DDNS: Select this option to enable the DDNS setting. Provider: Select a DDNS provider from the provider drop-down list. VIVOTEK offers Safe100.net, a free dynamic domain name service, to VIVOTEK customers� It is recommended that you register Safe100.net to access VIVOTEK’s Network Cameras from the...
Page 86 4� Select Enable DDNS and click Save to enable the setting� ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrators� You can use CustomSafe100 to register a dynamic domain name if your distributor or system integrators offer such services�...
Page 87 VIVOTEK Network > QoS (Quality of Service) Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network� Quality of service guarantees are important if the network capacity is insufficient, especially for real-time streaming multimedia applications. Quality can be defined as, for instance, a maintained level of bit rate, low latency, no packet dropping, etc.
Page 88 VIVOTEK QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer). The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Services Codepoint)� This is a 6-bit field that provides 64 different class IDs�...
Page 89: Network > Snmp (Simple Network Management Protocol)
VIVOTEK Network > SNMP (Simple Network Management Protocol) This section explains how to use the SNMP on the network camera� The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices� It helps network administrators to remotely manage network devices and find, solve network problems with ease.
Page 90: Security > User Account
VIVOTEK Security > User Account This section explains how to enable password protection and create multiple accounts� Root Password The administrator account name is “root”, which is permanent and can not be deleted� If you want to add more accounts in the Manage User column, please apply the password for the “root”...
Page 91: Security > Https (Hypertext Transfer Protocol Over Ssl)
VIVOTEK Security > HTTPS (Hypertext Transfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer)� It helps protect streaming data transmission over the Internet on higher security level� Create and Install Certificate Method Before using HTTPS for communication with the Network Camera, a Certificate must be created first.
Page 92 VIVOTEK 5� Click Home to return to the main page� Change the address from “http://” to “https://“ in the ad- dress bar and press Enter on your keyboard� Some Security Alert dialogs will pop up� Click OK or Yes to enable HTTPS�...
Page 93 VIVOTEK Create certificate and install : Select this option if you want to create a certificate from a certi- fication authority. 1� Select this option from a method pull-down menu� 2� Click Create certificate to generate the certificate. 3� The following information will appear in a pop-up window after clicking Create� If you see the fol- lowing Information bar, click OK and click on the Information bar at the top of the page to allow pop-ups�...
Page 94 VIVOTEK 4. The Certificate Information will automatically be displayed in the third column as shown below. You can click Property to see detailed information about the certificate. 5. Copy the contents of the Certificate request (in PEM format). Use the contents to apply for a 3rd-party certification authority such as Symantec VeriSign.
Page 95 VIVOTEK NOTE: NOTE ► How do I cancel the HTTPS settings? 1� Click on the Remove certificate button� 2� If you are currently running a secure connection The webpage will redirect to a non-HTTPS page automatically� Enable HTTPS Check this item to enable HTTPS communication, then select a connection option: "HTTP &...
Page 96: Security > Access List
VIVOTEK Security > Access List This section explains how to control access permission by verifying the client PC’s IP address� General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including stream 1 to stream 3). The default value is 10. If you modify the value and click Save, all current connections will be disconnected and automatically attempt to re-link (IE Explorer or Quick Time Player)�...
Page 97 VIVOTEK ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access� Please note that those checked connections will only be disconnected temporarily and will automatically try to re-link again (IE Explore or Quick Time Player)�...
Page 98 VIVOTEK There are three types of rules: Single: This rule allows the user to add an IP address to the Allowed/Denied list. For example: 192.168.2.1 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List�...
Page 99 Authentication server (usually a RADIUS server): Checks the client certificate and decides whether to accept the end user’s access request� ■ VIVOTEK Network Cameras support two types of EAP methods to perform authentication: EAP- PEAP and EAP-TLS� Please follow the steps below to enable 802.1x settings: 1�...
Page 100 VIVOTEK 3� When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802�1x enabled switch� The devices will then start the authentication automatically� NOTE: ► The authentication process for 802.1x: 1� The Certificate Authority (CA) provides the required signed certificates to the Network Camera (the supplicant) and the RADIUS Server (the authentication server)�...
Page 101: Ptz > Ptz Settings
VIVOTEK PTZ > PTZ settings This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation� Digital PTZ Operation (E-PTZ Operation) The e-PTZ control settings section will be displayed as shown below: 2010/12/10 17:08:56 2011/12/10 17:08:56 x1.8 Select Stream: Select a video stream to set up the e-PTZ control. Please note that each stream can possess its own preset and patrol settings�...
Page 102 VIVOTEK Home page in E-PTZ Mode 2014/08/10 17:08:56 x3.3 ■ The e-Preset Positions will also be displayed on the home page� Select one from the drop-down list, and the Network Camera will move to the selected position� ■ If you have set up different preset positions for different streams, you can select one of the video streams to display its separate preset positions�...
Page 103 VIVOTEK Patrol settings You can select some preset positions for the Network Camera to patrol� Please follow the steps below to set up a patrol schedule: 1� Select the preset locations on the list, and click � 2� The selected preset locations will be displayed on the Patrol locations list�...
Page 104 VIVOTEK NOTE: ► The Preset Positions will also be displayed on the home page. Select one from the Go to drop-down list, and the Network Camera will move to the selected preset position. ► Click Patrol: The Network Camera will patrol along the selected positions repeatedly. Please refer to page 103 to see more details.
Page 105: Event > Event Settings
VIVOTEK Event > Event settings This section explains how to configure the Network Camera to respond to particular situations (event)� A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notifications� Click on Help, there is an illustration shown in the pop-up window explaining that an event can be triggered by many sources, such as motion detection or external digital input devices�...
Page 106 VIVOTEK ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this option to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first.
Page 107 VIVOTEK ■ Audio detection A preset threshold can be configured with an external microphone as the trigger to system event. The triggering condition can be an input exceeding or falling below a threshold� Audio detection can take place as a complement to motion detection or as a method to detect activities not covered by the camera's view�...
Page 108 VIVOTEK ■ VADP It is presumed that you already uploaded and enabled the VADP modules before you can associatee VADP triggers with an Event setting� Click on the Set VADP Trigger button to open the VADP setup menu� The triggering conditions available with 3rd-party software modules known as VADP will be listed�...
Page 109 VIVOTEK 3� Action Define the actions to be performed by the Network Camera when a trigger is activated. ■ Trigger digital output for seconds Select this option to turn on the external digital output device when a trigger is activated� Specify the length of the trigger interval in the text box�...
Page 110 VIVOTEK Add server To set an event with recorded video or snapshots, it is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the Add server media files to) when a trigger is activated.
Page 111 VIVOTEK To verify if the email settings are correctly configured, click Test� The result will be shown in a pop-up window� If successful, you will also receive an email indicating the result� Click Save server to enable the settings� Note that after you set up the first event server, the new event server will automatically display on the Server list�...
Page 112 VIVOTEK ■ Passive mode Most firewalls do not accept new connections initiated from external requests� If the FTP server supports passive mode, select this option to enable passive mode FTP and allow data transmission to pass through the firewall. The firmware default has the Passive mode checkbox selected.
Page 113 VIVOTEK Network storage: Select to send the media files to a network storage location when a trigger is activated� Please refer to NAS server on page 132 for details� Click Save server to enable the settings� ■ SD Test: Click to test your SD card. The system will display a message indicating success or failure. If you want to use your SD card for local storage, please format it before use�...
Page 114 VIVOTEK Click 20140820 to open the directory: The format is: HH (24r) Click to open the file list for that hour 2014/08/20 2014/08/20 Click to go back to the previous Click to delete level of the directory selected items Click to delete all...
Page 115 VIVOTEK Add media Add media Click to open the media setting window� You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System log.
Page 116 VIVOTEK ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Snapshot_20140913_100341 File name preﬁx Date and time sufﬁx The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings�...
Page 117 VIVOTEK ■ Maximum file size Specify the maximum file size allowed. ■ File name prefix Enter the text that will be appended to the front of the file name. For example: Video_20140813_100341 File name preﬁx Date and time sufﬁx The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings�...
Page 118 VIVOTEK In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON, in order to enable the event triggering action� When completed, click Save event to enable the settings and click Close to exit Event Settings page�...
Page 119 Please note that there is a limited number of customized scripts you can upload; if the current amount of customized scripts has reached the limit, an alert message will prompt� If you need more information, please contact VIVOTEK technical support� 20140913...
Page 120: Applications > Motion Detection
VIVOTEK Applications > Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. 2010/12/10 17:08:56 Motion Detection Setting 1: For normal situations Motion Detection Setting 2:...
Page 121 VIVOTEK A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. Percentage = 30% If you want to configure other motion detection settings for day/night/schedule mode, please click Profile to open the Motion Detection Profile Settings page as shown below�...
Page 122 VIVOTEK NOTE: ► How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images� Pixel differences between the two frames are detected and highlighted in gray (frame C) and will be compared with the sensitivity setting� Sensitivity is a value that expresses the sensitivity to moving objects�...
Page 123: Applications > Di And Do
VIVOTEK Applications > DI and DO Connect DI or DO devices to the camera's terminal block, the camera will automatically detect the current connection state as pulled-high or pulled-low� You may then define the triggering condition� Digital input: Select High or Low to define the "Normal status" for the digital input. The Network Camera will report the current status�...
Page 124: Applications > Audio Detection
VIVOTEK Applications > Audio detection Audio detection, along with video motion detection, is applicable in the following scenarios: 1� Detection of activities not covered by camera view, e�g�, a loud input by gun shots or breaking a door/window� 2� A usually noisy environment, such as a factory, suddenly becomes quiet due to a breakdown of machines�...
Page 125 VIVOTEK You can use the Profile window to configure a different Audio detection setting. For example, a place can be noisy in the day time and become very quiet in the night� 1� Click on the Enable this profile checkbox� Once the Audio detection window is opened, the current sound input will be interactively indicated by a fluctuating yellow wave diagram.
Page 126: Applications > Vadp (Vivotek Application Development Platform)
Applications > VADP (VIVOTEK Application Development Platform) Users can store and execute VIVOTEK's or 3rd-party software modules onto the camera's flash memory or SD card� These software modules can apply in video analysis for intelligent video applications such as license plate recognition, object counting, or as an agent for edge recording, etc�...
Page 127 VIVOTEK To start a module, select the checkcircle in front, and click the Start button� If you should need to remove a module, select the checkcircle in front and then click the Stop button� By then the module status will become OFF, and the X button will appear at the end of the row�...
Page 128: Pir
VIVOTEK The indoor camera, FD8167, comes with a PIR (Passive Infrared sensor) detector� Select the checkbox on this page to enable the PIR function� 128 - User's Manual...
Page 129: Recording > Recording Settings
VIVOTEK Recording > Recording settings This section explains how to configure the recording settings for the Network Camera. Recording Settings Insert your SD card and click here to test NOTE: NOTE ► Please remember to format your SD card when using it for the first time. Please refer to page 134 for detailed information�...
Page 130 VIVOTEK If you enable adaptive recording and enable time-shift cache stream on Camera A, only when an event is triggered on Camera A will the server record the full frame rate streaming data; otherwise, it will only request the I frame data during normal monitoring, thus effectively save lots of bandwidths and storage space�...
Page 131 VIVOTEK 2� Destination You can select the SD card or networked storage (NAS) for the recorded video files� If you have not configured a NAS server, see details in the following. NAS server Click Add NAS server to open the server setting window and follow the steps below to set up: 1�...
Page 132 VIVOTEK If successful, you will receive a test.txt file on the network storage server. 3� Enter a server name� 4� Click Save to complete the settings and click Close to exit the page� ■ Capacity: You can choose either the entire free space available or limit the reserved space. The recording size limit must be larger than the reserved amount for cyclic recording�...
Page 133 VIVOTEK Event f you want to enable recording notification, please click to configure event triggering settings. Please refer to Event > Event settings on page 105 for more details� When completed, select Enable this recording� Click Save to enable the setting and click Close to exit this page.
Page 134: Local Storage > Sd Card Management
VIVOTEK Local storage > SD card management This section explains how to manage the local storage on the Network Camera� Here you can view SD card status, and implement SD card control� SD card staus This column shows the status and reserved space of your SD card� Please remember to format the SD card when using for the first time.
Page 135: Local Storage > Content Management
VIVOTEK Local storage > Content management This section explains how to manage the content of recorded videos on the Network Camera� Here you can search and view the records and view the searched results� Searching and Viewing the Records This column allows the user to set up search criteria for recorded data� If you do not select any criteria and click Search button, all recorded data will be listed in the Search Results column�...
Page 136: Search Results
VIVOTEK Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked� Click to sort the search results in either direction� Enter a key word to filter the Numbers of entries displayed...
Page 137 VIVOTEK ■ Lock/Unlock: Select the desired search results, then click this button. The selected items will become Locked, which will not be deleted during cyclic recording� You can click again to unlock the selections� For example: Click to switch pages ■...
Page 138: Url Commands For The Network Camera
VIVOTEK Appendix URL Commands for the Network Camera 1. Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax� This section specifies the external HTTP-based application programming interface�...
Page 139: General Cgi Url Syntax And Parameters
VIVOTEK URL commands for FD8167 URL Command Document for All Series 3. General CGI URL Syntax and Parameters When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera or video server. The CGIs are organized in functionally-related directories under the cgi-bin directory.
Page 140: Security Level
VIVOTEK URL commands for FD8167 URL Command Document for All Series 4. Security Level SECURITY SUB-DIRECTORY DESCRIPTION LEVEL anonymous Unprotected. 1 [view] anonymous, viewer, 1. Can view, listen, talk to camera. dido, camctrl 2. Can control DI/DO, PTZ of the camera.
Page 141: Get Server Parameter Values
VIVOTEK URL commands for FD8167 URL Command Document for All Series 5. Get Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://<servername>/cgi-bin/anonymous/getparam.cgi?[<parameter>] [&<parameter>…] http://<servername>/cgi-bin/viewer/getparam.cgi?[<parameter>] [&<parameter>…] http://<servername>/cgi-bin/operator/getparam.cgi?[<parameter>] [&<parameter>…] http://<servername>/cgi-bin/admin/getparam.cgi?[<parameter>] [&<parameter>…] Where the <parameter> should be <group>[_<name>]. If you do not specify any parameters, all the parameters on the server will be returned.
Page 142 VIVOTEK URL commands for FD8167 URL Command Document for All Series Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network_ipaddress=192.168.0.123\r\n 142 - User's Manual...
Page 143: Set Server Parameter Values
VIVOTEK URL commands for FD8167 URL Command Document for All Series 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://<servername>/cgi-bin/anonymous/setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&return=<return page>] http://<servername>/cgi-bin/viewer/setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&return=<return page>] http://<servername>/cgi-bin/operator/setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&return=<return page>] http://<servername>/cgi-bin/admin/setparam.cgi? <parameter>=<value>...
Page 144 VIVOTEK URL commands for FD8167 URL Command Document for All Series Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n...
Page 145: Available Parameters On The Server
URL Command Document for All Series 7. Available parameters on the server This chapter defines all the parameters which can be configured or retrieved from VIVOTEK network camera or video server. The general format of description is listed in the table below...
Page 146 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.1 system Group: system NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) hostname string[64] Mega-Pixel Host name of server. Network Camera ledoff <boolean> Turn on (0) or turn off (1) all led indicators.
Page 147 VIVOTEK URL commands for FD8167 URL Command Document for All Series America, Central Time, Mexico City, Saskatchewan -200: GMT-05:00 Eastern Time, New York, Toronto -201: GMT-05:00 Bogota, Lima, Quito, Indiana -180: GMT-04:30 Caracas -160: GMT-04:00 Atlantic Time, Canada, La Paz,...
Page 148 VIVOTEK URL commands for FD8167 URL Command Document for All Series Muscat, Baku, Tbilisi, Yerevan 180: GMT 04:30 Kabul 200: GMT 05:00 Ekaterinburg, Islamabad, Karachi, Tashkent 220: GMT 05:30 Calcutta, Chennai, Mumbai, New Delhi 230: GMT 05:45 Kathmandu 240: GMT 06:00 Almaty,...
Page 149 VIVOTEK URL commands for FD8167 URL Command Document for All Series daylight_timezones string List time zone index which support daylight saving time. updateinterval 0 to Disable automatic time 3600, adjustment, otherwise, it 86400, indicates the seconds between 604800, NTP automatic update 2592000 intervals.
Page 150 VIVOTEK URL commands for FD8167 URL Command Document for All Series combined results. restoreexceptlang Restore the system <positive parameters to default values integer> except the custom language file the user has uploaded. This command can cooperate with other “restoreexceptXYZ” commands. When...
Page 151 VIVOTEK URL commands for FD8167 URL Command Document for All Series serialnumber <mac <product 12 characters MAC address address> (without hyphens). address> firmwareversion string[40] <product Firmware version, including dependent> model, company, and version number in the format: <MODEL-BRAND-VERSION> language_count <integer>...
Page 152 VIVOTEK URL commands for FD8167 URL Command Document for All Series connections. onlinenum_httppush integer Current number of HTTP push server connections. eth_i0 <string> <blank> Get network information from mii-tool. vi_i<0~(nvi-1)> <boolean> Virtual input 0 => Inactive 1 => Active 7.3 digital input behavior define Group: di_i<0~(ndi-1)>...
Page 153 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.6 security Group: security NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) privilege_do view, operator, operator Indicate which privileges and admin above can control digital output (capability.ndo > 0) privilege_camctrl view, operator,...
Page 154 VIVOTEK URL commands for FD8167 URL Command Document for All Series Stopped service will auto-start after changing port settings. Change HTTP port from 80 to 5556, and change RTP port for video from 5556 to 20480. Then, set preprocess=9 to stop both service first.
Page 155 VIVOTEK URL commands for FD8167 URL Command Document for All Series identity_tls String[64] <blank> TLS identity password String[200] <blank> Password for TLS privatekeypassword String[200] <blank> Password for PEAP ca_exist <boolean> CA installed flag ca_time <integer> CA installed time. Represented in EPOCH ca_size <integer>...
Page 156 VIVOTEK URL commands for FD8167 URL Command Document for All Series management 0~63 Management channel for DSCP eventtunnel 0~63 Event/Control channel for DSCP 7.7.3 IPV6 Subgroup of network: ipv6 NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enable <boolean> Enable IPv6. addonipaddress <ip address>...
Page 157 VIVOTEK URL commands for FD8167 URL Command Document for All Series anonymousviewing <boolean> Enable anoymous streaming viewing. 7.7.6 HTTPS port Subgroup of network: https NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) port 443, 1025 ~ HTTPS port. 65535 7.7.7 RTSP Subgroup of network: rtsp...
Page 158 VIVOTEK URL commands for FD8167 URL Command Document for All Series audioport 1025 ~ 65535 5562+n*2 Multicast audio port. metadataport 1026~65534 6560+n*2 Multicast metadata port. 1 ~ 255 Mutlicast time to live value. 7.7.8 RTP port Subgroup of network: rtp...
Page 159: Video Input
VIVOTEK URL commands for FD8167 URL Command Document for All Series 1 => deny ipv4list_i<0~9> Single address: IPv4 address list. <blank> <ip address> Network address: <ip address / network mask> Range address:<start ip address - end ip address> ipv6list_i<0~9> String[43] IPv6 address list.
Page 160 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7. 9.1 video input setting per channel Group: videoin_c<0~(n-1)> for n channel products, and m is stream number NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) whitebalance auto, auto “auto” indicates auto white manual, balance.
Page 161 VIVOTEK URL commands for FD8167 URL Command Document for All Series Bit 2 => Support pan operation; 0(not support), 1(support) Bit 3 => Support tilt operation; 0(not support), 1(support) Bit 4 => Support zoom operation; 0(not support), 1(support) Bit 5 => Support focus operation;...
Page 162 VIVOTEK URL commands for FD8167 URL Command Document for All Series s<0~(m-1)>_h264_ratecontro cbr, vbr cbr, constant bitrate lmode vbr, fix quality s<0~(m-1)>_h264_quant 1~5,99, 100 Quality of video when choosing vbr in “ratecontrolmode”. 1 = worst quality, 5 = best quality.
Page 163 VIVOTEK URL commands for FD8167 URL Command Document for All Series s<0~(m-1)>_mjpeg_quant 1~5, 99, 100 Quality of JPEG video. 1 = worst quality, 5 = best quality. 100: Use the quality level in "qpercent" 99: Use the quality level in "qvalue"...
Page 164 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.9.1.1 Alternative video input profiles per channel In addition to the primary setting of video input, there can be alternative profile video input setting for each channel which might be for different scene of light (daytime or nighttime).
Page 165 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.10 IR cut control Group: ircutcontrol NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) mode auto, auto Set IR cut control mode day, night, schedule <boolean> Enable/disable Smart IR daymodebegintime 00:00~23:59...
Page 166 VIVOTEK URL commands for FD8167 URL Command Document for All Series sharpness -3 ~ 3, 100 Adjust sharpness of image according to mode settings. sharpnesspercent 0~100 Adjust sharpness of image by percentage. Softer 0 <-> 100 Sharper gammacurve 0~100 Gamma curve.
Page 167 VIVOTEK URL commands for FD8167 URL Command Document for All Series percentage according to mode settings. profile_i0_sharpness -3~3,100 Adjust sharpness of image according to mode settings. profile_i0_sharpnessperce 0~100 Adjust sharpness value of percentage when sharpness=100 profile_i0_gammacurve 0~100 Gamma curve profile_i0_dnr_mode 3D noise reduction.
Page 168: Motion Detection Settings
VIVOTEK URL commands for FD8167 URL Command Document for All Series profile_i0_enable <boolean> Enable/disable this profile setting profile_i0_policy day, night The mode which the profile night, is applied to. schedule profile_i0_begintime hh:mm 18:00 Begin time of schedule mode. profile_i0_endtime hh:mm 06:00 End time of schedule mode.
Page 169 VIVOTEK URL commands for FD8167 URL Command Document for All Series win_i<0~2>_height 0 ~ 240 Height of motion detection window. win_i<0~2>_objsize 0 ~ 100 Percent of motion detection window. win_i<0~2>_sensitivity 0 ~ 100 Sensitivity of motion detection window. Group: motion_c<0~(n-1)> profile for m profile and n channel product (capability.nmotionprofile >...
Page 170 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.15 Tampering detection settings Group: tampering_c<0~(n-1)> for n channel product NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enable <boolean> Enable or disable tamper detection. duration 10 ~ 600 If tampering value exceeds the ‘threshold’ for more than ‘duration’...
Page 171 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.16.1 Express link Group:expresslink NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enable <boolean> Enable or disable express link. state onlycheck, badnetwork “onlycheck” : You have to input the onlyoffline, host name of your camera and press checkonline, "Register"...
Page 172: System Log
VIVOTEK URL commands for FD8167 URL Command Document for All Series forwarding 7.19 System log Group: syslog NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enableremotelog <boolean> Enable remote log. serverip <IP address> <blank> Log server IP address. serverport 514, 1025~65535 514 Server port used for log.
Page 173 Hyperlink of the logo vivotek.co logo_powerbyvvtk_hidden <boolean> 0 => display the power by vivotek logo 1 => hide the power by vivotek logo theme_option 1~3: One of the default themes. 4: Custom definition. theme_color_font string[7] #ffffff Font color...
Page 174: Privacy Mask
VIVOTEK URL commands for FD8167 URL Command Document for All Series theme_color_configbackground string[7] #323232 Background color of configuration area. theme_color_videobackground string[7] #565656 Background color of video area. theme_color_case string[7] #323232 Frame color custombutton_manualtrigger_s <boolean> Show or hide manual trigger (VI) button in homepage 0 ->...
Page 175 VIVOTEK URL commands for FD8167 URL Command Document for All Series <positive (Recommand to use ir for integer> built-in IR and extir for external IR) 0/99 npir Number of PIRs. <positive integer> 0/99 Number of digital inputs. <positive integer> 0/99 Number of virtual inputs <positive...
Page 176 VIVOTEK URL commands for FD8167 URL Command Document for All Series integer> can be set separately as follows: Bit 0 => Support camera control function; 0(not support), 1(support) Bit 1 => Built-in or external video source; 0(external), 1(built-in) Bit 2 => Support pan...
Page 177 VIVOTEK URL commands for FD8167 URL Command Document for All Series VS8102: 0b10111101 0/99 windowless <boolean> Indicate whether to support windowless plug-in. 0/99 eptz 0, <positive A 32-bit integer, each bit integer> can be set separately as follows: Bit 0 => stream 1 supports ePTZ or not.
Page 178 VIVOTEK URL commands for FD8167 URL Command Document for All Series 0/99 protocol_spush_mjpeg <boolean> Indicate whether to support server push MJPEG. 0/99 protocol_snmp <boolean> Indicate whether to support SNMP. 0/99 protocol_ipv6 <boolean> Indicate whether to support IPv6. 0/99 protocol_pppoe <boolean>...
Page 179 VIVOTEK URL commands for FD8167 URL Command Document for All Series video mode. videoin_c0_maxframerate <a list of 0/99 Available maximum available frame list. maximum frame rate separated by commas> videoin_c0_mjpeg_maxfra <a list of 0/99 Available maximum merate available codec frame list.
Page 180 VIVOTEK URL commands for FD8167 URL Command Document for All Series (It will be replaced by audio_mic and audio_extmic.) audio_lineout 0/99 <boolean> Indicate whether to support line output. 0/99 audio_headphoneout <boolean> Indicate whether to support headphone output. audioin_codec 0/99 <string>...
Page 181 VIVOTEK URL commands for FD8167 URL Command Document for All Series 0/99 network_wireless <boolean> Indicate whether to support wireless. 0/99 derivative_brand <boolean> Indicate whether to support the upgrade function for the derivative brand. For example, if the value is true, the VVTK product can be upgraded to VVXX.
Page 182 VIVOTEK URL commands for FD8167 URL Command Document for All Series 0/99 version_onvifevent <string> 1.3.0.7 Indicate ONVIF event version 0/99 media_totalspace <positive 20000 Available memory space integer> (KB) for media. 0/99 media_snapshot_sizepersecond <positive Maximum size (KB) of integer> one snapshot image.
Page 183 VIVOTEK URL commands for FD8167 URL Command Document for All Series remotecamctrl_master 0, <positive 0/99 Indicate whether to integer> support remote auxiliary camera (master side), this value means supporting max number of auxiliary camera. remotecamctrl_slave <boolean> 0/99 Indicate whether to support remote camera control (slave side).
Page 184 VIVOTEK URL commands for FD8167 URL Command Document for All Series manual tracking window of integer> manual smartstream_nwindow_ 0/99 number of <positive Maximum hybrid_autotracking tracking window of integer> autotracking in hybrid mode smartstream_nwindow_ 0/99 number of <positive Maximum hybrid_ manual tracking window of integer>...
Page 185 VIVOTEK URL commands for FD8167 URL Command Document for All Series "-": No Iris control support * Note: For some cameras, this value may be varied depending on mounted lens. 0/99 focusassist 0, 1 0: Non-support focus assistance 1: Support focus assistance...
Page 186 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.24 WebAPI: Information for a channel Group: capability_videoin_c<n>, n = channel index from 0 to "capability_nvideoin"-1 PARAMETER VALUE DEFAULT SECURITY DESCRIPTION (get/set) nmode <Positive 0/99 Indicate how many video modes Integer>...
Page 187 VIVOTEK URL commands for FD8167 URL Command Document for All Series mjpeg_maxbitrate <Positive 40000000 0/99 Maximum bitrates of MJPEG. Integer>, - The unit is bps. "-" means MJPEG does not support bit rate control. h264_ maxframerate A list of 0/99 Maximum fps that the device can <Positive...
Page 188 VIVOTEK URL commands for FD8167 URL Command Document for All Series binning 0, 1, 3 0/99 Indicate binning is used or not in this video mode. 0: No binning 1: 2x2 binning 3: 3x3 binning nresolution <Positive 0/99 How many resolution options in this Integer>...
Page 189: Event Setting
VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.26 Customized event script Group: event_customtaskfile_i<0~2> PARAMETER VALUE Default SECURITY DESCRIPTION (get/set) name string[40] NULL Custom script identification of this entry. date string[4-20] NULL Date of custom script. time...
Page 190 VIVOTEK URL commands for FD8167 URL Command Document for All Series 0, 1 Indicate the source id of di trigger. This field is required when trigger condition is “di”. One bit represents one digital input. The LSB indicates DI 0.
Page 191 VIVOTEK URL commands for FD8167 URL Command Document for All Series endtime hh:mm 24:00 End time of the weekly schedule. (00:00 ~ 24:00 sets schedule as always on) action_do_i<0~(ndo-1) 0, 1 Enable or disable trigger digital >_enable output. action_do_i<0~(ndo-1) 1~999 Duration of the digital output >_duration...
Page 192 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.28 Server setting for event action Group: server_i<0~4> PARAMETER VALUE DEFAULT SECURITY DESCRIPTION (get/set) name string[40] NULL Identification of this entry type email, email Indicate the server type: ftp, “email”...
Page 193 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.29 Media setting for event action Group: media_i<0~4> (media_freespace is used internally.) PARAMETER VALUE DEFAULT SECURITY DESCRIPTION (get/set) name string[40] NULL Identification of this entry type snapshot, snapshot Media type to send to the server or systemlog, store on the server.
Page 194 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.30 Recording Group: recording_i<0~1> PARAMETER VALUE DEFAULT SECURITY DESCRIPTION (get/set) name string[40] NULL Identification of this entry. enable 0, 1 Enable or disable this recording. priority 0, 1, 2...
Page 195 VIVOTEK URL commands for FD8167 URL Command Document for All Series weekday 0~127 Indicate which weekday is scheduled. One bit represents one weekday. bit0 (LSB) = Saturday bit1 = Friday bit2 = Thursday bit3 = Wednesday bit4 = Tuesday bit5 = Monday...
Page 196 VIVOTEK URL commands for FD8167 URL Command Document for All Series adaptive_preevent Indicate when is the adaptive recording started before the event trigger point (seconds) adaptive_postevent 0~10 Indicate when is the adaptive recording stopped after the event trigger point (seconds) Unit: Mega bytes.
Page 197: Region Of Interest
VIVOTEK URL commands for FD8167 URL Command Document for All Series localityname string[128] Asia The locality name in the certificate information. organizationname string[64] VIVOTEK Organization name in the Inc. certificate information. unit string[64] VIVOTEK Organizational unit name in the Inc.
Page 198: Eptz Setting
VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.34 ePTZ setting Group: eptz_c<0~(n-1)> for n channel product. PARAMETER VALUE Default SECURITY DESCRIPTION (get/set) osdzoom <boolean> Indicates multiple of zoom in is “on-screen display” or not smooth <boolean>...
Page 199 VIVOTEK URL commands for FD8167 URL Command Document for All Series preset_i<0~19>_size <window size> <blank> Width and height of the preset. (It should be set by ePreset.cgi rather than by setparam.cgi.) 7.35 Exposure window setting per channel Group: exposurewin_c<0~(n-1)> for n channel products...
Page 200 VIVOTEK URL commands for FD8167 URL Command Document for All Series window. custom: Use inclusive and exclusive window. blc: Use BLC. i<0~(m-1)>_win_i<0~9 <boolean> Enable or disable the >_enable window. i<0~(m-1)>_win_i<0~9 0: Indicate exclusive. >_policy 1: Indicate inclusive. i<0~(m-1)>_win_i<0~9 <coordinate> 110,90 Left-top corner >_home...
Page 201 VIVOTEK URL commands for FD8167 URL Command Document for All Series 7.37 VIVOTEK Application Development Platform setting Group: vadp NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) version <string> 1.2.1.0 Indicate the VADP version. resource_total_memory <integer> <product Indicate total dependent> available memory size for VADP modules.
Page 202 VIVOTEK URL commands for FD8167 URL Command Document for All Series Group: vadp_module_i<0~(n-1)> NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enable <boolean> Indicate if the module is enabled or not. If yes, also add the index of this module to the module_order.
Page 203: Drive The Digital Output
VIVOTEK URL commands for FD8167 URL Command Document for All Series 8. Useful Functions 8.1 Drive the Digital Output Note: This request requires Viewer privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/dido/setdo.cgi?do1=<state>[&do2=<state>] [&do3=<state>][&do4=<state>] Where state is 0 or 1; “0” means inactive or normal state, while “1” means active or triggered state.
Page 204: Query Status Of The Digital Output
VIVOTEK URL commands for FD8167 URL Command Document for All Series [di2=<state>]\r\n [di3=<state>]\r\n where <state> can be 0 or 1. Example: Query the status of digital input 1 . Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di1=1\r\n 8.3 Query Status of the Digital Output...
Page 205: Capture Single Snapshot
VIVOTEK URL commands for FD8167 URL Command Document for All Series Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n do1=1\r\n 8.4 Capture Single Snapshot Note: This request requires Normal User privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/viewer/video.jpg?[channel=<value>][&resolution=<value>] [&quality=<value>][&streamid=<value>] If the user requests a size larger than all stream settings on the server, this request will fail.
Page 206: Account Management
VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.5 Account Management Note: This request requires Administrator privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/admin/editaccount.cgi? method=<value>&username=<name>[&userpass=<value>][&privilege=<value>] [&privilege=<value>][…][&return=<return page>] PARAMETER VALUE DESCRIPTION method Add an account to the server. When using this method, the “username”...
Page 207: System Logs
VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.6 System Logs Note: This request require Administrator privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/admin/syslog.cgi Server will return the most up-to-date system log. Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: <syslog length>\r\n \r\n <system log information>\r\n...
Page 208 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.8 ePTZ Camera Control Note: This request requires camctrl privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/camctrl/eCamCtrl.cgi?channel=<value>&stream=<value> [&move=<value>] – Move home, up, down, left, right [&auto=<value>] – Auto pan, patrol [&zoom=<value>] – Zoom in, out [&zooming=<value>&zs=<value>]...
Page 209 VIVOTEK URL commands for FD8167 URL Command Document for All Series zoom wide Zoom larger view with current speed. tele Zoom further with current speed. zooming wide or tele Zoom without stopping for larger view or further view with zs speed, used for joystick control.
Page 210 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.9 ePTZ Recall Note: This request requires camctrl privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/camctrl/eRecall.cgi?channel=<value>&stream=<value>& recall=<value>[&return=<return page>] PARAMETER VALUE DESCRIPTION channel <0~(n-1)> Channel of the video source. stream <0~(m-1)> Stream. recall Text string less than One of the present positions to recall.
Page 211 VIVOTEK URL commands for FD8167 URL Command Document for All Series relative path according to the current path. 8.11 IP Filtering Note: This request requires Administrator access privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/admin/ipfilter.cgi? method=<value>&[start=<ipaddress>&end=<ipaddress>][&index=<value>] [&return=<return page>] PARAMETER VALUE DESCRIPTION method addallow Add allowed IP address range to the server.
Page 212 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.11.1 IP Filtering for ONVIF Syntax: <product dependent> http://<servername>/cgi-bin/admin/ipfilter.cgi?type[=<value>] http://<servername>/cgi-bin/admin/ipfilter.cgi?method=add<v4/v6>&ip=<ipaddress>[&index=<valu e>][&return=<return page>] http://<servername>/cgi-bin/admin/ipfilter.cgi?method=del<v4/v6>&index=<value>[&return=<return page>] PARAMETER VALUE DESCRIPTION type NULL Get IP filter type allow, deny Set IP filter type...
Page 213 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.12 Event/Control HTTP Tunnel Channel Note: This request requires Administrator privileges. Method: GET and POST Syntax: http://<servername>/cgi-bin/admin/ctrlevent.cgi ------------------------------------------------------------------------- GET /cgi-bin/admin/ctrlevent.cgi x-sessioncookie: string[22] accept: application/x-vvtk-tunnelled pragma: no-cache cache-control: no-cache ------------------------------------------------------------------------- POST /cgi-bin/admin/ ctrlevent.cgi...
Page 214 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.13 Get SDP of Streams Note: This request requires Viewer access privileges. Method: GET Syntax: http://<servername>/<network_rtsp_s<0~m-1>_accessname> “m” is the stream number. “network_accessname_<0~(m-1)>” is the accessname for stream “1” to stream “m”. Please refer to the “subgroup of network: rtsp”...
Page 215 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.15 Storage managements Note: This request requires administrator privileges. Method: GET and POST Syntax: http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=<cmd_type>[&<parameter>=<value>…] The commands usage and their input arguments are as follows. PARAMETER VALUE DESCRIPTION cmd_type <string>...
Page 216 VIVOTEK URL commands for FD8167 URL Command Document for All Series isLocked <boolean> Optional. Indicate if the file is locked or not. 0: file is not locked. 1: file is locked. A locked file would not be removed from UI or cyclic storage.
Page 217 VIVOTEK URL commands for FD8167 URL Command Document for All Series Command: update PARAMETER VALUE DESCRIPTION label <integer primary key> Required. Identify the designated record. Ex. label=1 isLocked <boolean> Required. Indicate if the file is locked or not. Ex. Update records whose key numbers are 1 and 5 to be locked status.
Page 218 VIVOTEK URL commands for FD8167 URL Command Document for All Series Subgroup of stormgr: i<0~(n-1)>: n is the total number of displayed records. Element name Type Description label <Integer Primary Key> A unique integer. triggerType <Text> Indicate the event trigger type.
Page 219 VIVOTEK URL commands for FD8167 URL Command Document for All Series 12:00:00</triggerTime> <triggerTime>2009-01-24 <backup>0</backup> </i0> <i1> <label>2</label> <triggerType>di</triggerType> <mediaType>snapshot</mediaType> <destPath>/mnt/auto/NCMF/123/123.jpg</destPath> <resolution>800x600</resolution> <isLocked>0</isLocked> 12:01:00</triggerTime> <triggerTime>2009-01-24 <backup>0</backup> </i1> </stormgr> Ex. Local storage status in XML format. <?xml version="1.0" encoding="ISO-8859-1" ?> <stormgr version="0.0.0.1">...
Page 220 VIVOTEK URL commands for FD8167 URL Command Document for All Series retType xml or javascript Optional. Ex. retype=javascript The default return message is in XML format. Ex. Query local storage status and call for javascript format return message. http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=queryStatus&retType=javascript There are two cgi commands for download and composing jpegs to avi format.
Page 221 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.16 Virtual input Note: Change virtual input (manual trigger) status. Method: GET/POST Syntax: http://<servername>/cgi-bin/admin/setvi.cgi?vi0=<value>[&vi1=<value>][&vi2=<value>] [&return=<return page>] PARAMETER VALUE DESCRIPTION vi<num> state[(duration)nstate] Ex: vi0=1 Setting virtual input 0 to trigger state Where "state"...
Page 222 VIVOTEK URL commands for FD8167 URL Command Document for All Series The resource is unavailable, ex. Virtual input is waiting for next state. Examples: 1. setvi.cgi?vi0=0(15000)1 2. setvi.cgi?vi0=1 Request 2 will not be accepted during the execution time(15 seconds). 8.17 Open Timeshift Stream (timeshift_enable=1, timeshift_c<n>_s<m>_allow=1)
Page 223 VIVOTEK URL commands for FD8167 URL Command Document for All Series request. Ex: Request the streaming from 12:20 rtsp://10.0.0.1/live.sdp?maxsft=10&reftime=12:30 forcechk Check if the requested stream enables timeshift, feature and if minsft is achievable. If false, return “415 Unsupported Media Type”.
Page 224 VIVOTEK URL commands for FD8167 URL Command Document for All Series mjpeg_quant 0, 1~5 Quality of JPEG video. 99, 1~5 0,99 is the customized manual <product dependent> input setting. 1 = worst quality, 5 = best quality. <product dependent> mjpeg_qvalue 10~200 Manual video quality level input.
Page 225 VIVOTEK URL commands for FD8167 URL Command Document for All Series h264_ratecontrolmode cbr, vbr, smart cbr: constant bitrate vbr: fix quality smart: smart stream h264_quant 0, 1~5 Quality of video when choosing 99, 1~5 vbr in “h264_ratecontrolmode”. <product dependent> 0,99 is the customized manual input setting.
Page 226 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.19 Export Files Note: This request requires Administrator privileges. Method: GET Syntax: For daylight saving time configuration file: http://<servername>/cgi-bin/admin/exportDst.cgi For language file: http://<servername>/cgi-bin/admin/export_language.cgi?currentlanguage=<value> PARAMETER VALUE DESCRIPTION currentlanguage 0~20 Available language lists.
Page 227 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.20 Upload Files Note: This request requires Administrator privileges. Method: POST Syntax: For daylight saving time configuration file: http://<servername>/cgi-bin/admin/upload_dst.cgi Post data: filename =<file name>\r\n \r\n <multipart encoded form data>...
Page 228 VIVOTEK URL commands for FD8167 URL Command Document for All Series 8.21 Media on demand Media on demand allows users to select and receive/watch/listen to metadata/video/audio contents on demand. Note: This request requires Viewer access privileges. Syntax: rtsp://<servername>/mod.sdp?[&stime=<value>][&etime=<value>][&length =<value>][&loctime =<value>][&file=<value>][&tsmode=<value>]...
Page 229 VIVOTEK URL commands for FD8367 URL Command Document for All Series 3. General CGI URL Syntax and Parameters When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera or video server. The CGIs are organized in functionally-related directories under the cgi-bin directory.
Page 230 VIVOTEK URL commands for FD8367 URL Command Document for All Series 4. Security Level SECURITY SUB-DIRECTORY DESCRIPTION LEVEL anonymous Unprotected. 1 [view] anonymous, viewer, 1. Can view, listen, talk to camera. dido, camctrl 2. Can control DI/DO, PTZ of the camera.
Page 231 VIVOTEK URL commands for FD8367 URL Command Document for All Series 5. Get Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://<servername>/cgi-bin/anonymous/getparam.cgi?[<parameter>] [&<parameter>…] http://<servername>/cgi-bin/viewer/getparam.cgi?[<parameter>] [&<parameter>…] http://<servername>/cgi-bin/operator/getparam.cgi?[<parameter>] [&<parameter>…] http://<servername>/cgi-bin/admin/getparam.cgi?[<parameter>] [&<parameter>…] Where the <parameter> should be <group>[_<name>]. If you do not specify any parameters, all the parameters on the server will be returned.
Page 232 VIVOTEK URL commands for FD8367 URL Command Document for All Series Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network_ipaddress=192.168.0.123\r\n 232 - User's Manual...
Page 233 VIVOTEK URL commands for FD8367 URL Command Document for All Series 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://<servername>/cgi-bin/anonymous/setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&return=<return page>] http://<servername>/cgi-bin/viewer/setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&return=<return page>] http://<servername>/cgi-bin/operator/setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&return=<return page>] http://<servername>/cgi-bin/admin/setparam.cgi? <parameter>=<value>...
Page 234 VIVOTEK URL commands for FD8367 URL Command Document for All Series Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n...
Page 235 URL Command Document for All Series 7. Available parameters on the server This chapter defines all the parameters which can be configured or retrieved from VIVOTEK network camera or video server. The general format of description is listed in the table below...
Page 236 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.1 system Group: system NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) hostname string[64] Mega-Pixel Host name of server. Network Camera ledoff <boolean> Turn on (0) or turn off (1) all led indicators.
Page 237 VIVOTEK URL commands for FD8367 URL Command Document for All Series America, Central Time, Mexico City, Saskatchewan -200: GMT-05:00 Eastern Time, New York, Toronto -201: GMT-05:00 Bogota, Lima, Quito, Indiana -180: GMT-04:30 Caracas -160: GMT-04:00 Atlantic Time, Canada, La Paz,...
Page 238 VIVOTEK URL commands for FD8367 URL Command Document for All Series Muscat, Baku, Tbilisi, Yerevan 180: GMT 04:30 Kabul 200: GMT 05:00 Ekaterinburg, Islamabad, Karachi, Tashkent 220: GMT 05:30 Calcutta, Chennai, Mumbai, New Delhi 230: GMT 05:45 Kathmandu 240: GMT 06:00 Almaty,...
Page 239 VIVOTEK URL commands for FD8367 URL Command Document for All Series daylight_timezones string List time zone index which support daylight saving time. updateinterval 0 to Disable automatic time 3600, adjustment, otherwise, it 86400, indicates the seconds between 604800, NTP automatic update 2592000 intervals.
Page 240 VIVOTEK URL commands for FD8367 URL Command Document for All Series combined results. restoreexceptlang Restore the system <positive parameters to default values integer> except the custom language file the user has uploaded. This command can cooperate with other “restoreexceptXYZ” commands. When...
Page 241 VIVOTEK URL commands for FD8367 URL Command Document for All Series serialnumber <mac <product 12 characters MAC address address> (without hyphens). address> firmwareversion string[40] <product Firmware version, including dependent> model, company, and version number in the format: <MODEL-BRAND-VERSION> language_count <integer>...
Page 242 VIVOTEK URL commands for FD8367 URL Command Document for All Series connections. onlinenum_httppush integer Current number of HTTP push server connections. eth_i0 <string> <blank> Get network information from mii-tool. vi_i<0~(nvi-1)> <boolean> Virtual input 0 => Inactive 1 => Active 7.3 digital input behavior define Group: di_i<0~(ndi-1)>...
Page 243 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.6 security Group: security NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) privilege_do view, operator, operator Indicate which privileges and admin above can control digital output (capability.ndo > 0) privilege_camctrl view, operator,...
Page 244 VIVOTEK URL commands for FD8367 URL Command Document for All Series Stopped service will auto-start after changing port settings. Change HTTP port from 80 to 5556, and change RTP port for video from 5556 to 20480. Then, set preprocess=9 to stop both service first.
Page 245 VIVOTEK URL commands for FD8367 URL Command Document for All Series identity_tls String[64] <blank> TLS identity password String[200] <blank> Password for TLS privatekeypassword String[200] <blank> Password for PEAP ca_exist <boolean> CA installed flag ca_time <integer> CA installed time. Represented in EPOCH ca_size <integer>...
Page 246 VIVOTEK URL commands for FD8367 URL Command Document for All Series management 0~63 Management channel for DSCP eventtunnel 0~63 Event/Control channel for DSCP 7.7.3 IPV6 Subgroup of network: ipv6 NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enable <boolean> Enable IPv6. addonipaddress <ip address>...
Page 247 VIVOTEK URL commands for FD8367 URL Command Document for All Series anonymousviewing <boolean> Enable anoymous streaming viewing. 7.7.6 HTTPS port Subgroup of network: https NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) port 443, 1025 ~ HTTPS port. 65535 7.7.7 RTSP Subgroup of network: rtsp...
Page 248 VIVOTEK URL commands for FD8367 URL Command Document for All Series audioport 1025 ~ 65535 5562+n*2 Multicast audio port. metadataport 1026~65534 6560+n*2 Multicast metadata port. 1 ~ 255 Mutlicast time to live value. 7.7.8 RTP port Subgroup of network: rtp...
Page 249 VIVOTEK URL commands for FD8367 URL Command Document for All Series 1 => deny ipv4list_i<0~9> Single address: IPv4 address list. <blank> <ip address> Network address: <ip address / network mask> Range address:<start ip address - end ip address> ipv6list_i<0~9> String[43] IPv6 address list.
Page 250 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7. 9.1 video input setting per channel Group: videoin_c<0~(n-1)> for n channel products, and m is stream number NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) whitebalance auto, auto “auto” indicates auto white manual, balance.
Page 251 VIVOTEK URL commands for FD8367 URL Command Document for All Series Bit 2 => Support pan operation; 0(not support), 1(support) Bit 3 => Support tilt operation; 0(not support), 1(support) Bit 4 => Support zoom operation; 0(not support), 1(support) Bit 5 => Support focus operation;...
Page 252 VIVOTEK URL commands for FD8367 URL Command Document for All Series s<0~(m-1)>_h264_ratecontro cbr, vbr cbr, constant bitrate lmode vbr, fix quality s<0~(m-1)>_h264_quant 1~5,99, 100 Quality of video when choosing vbr in “ratecontrolmode”. 1 = worst quality, 5 = best quality.
Page 253 VIVOTEK URL commands for FD8367 URL Command Document for All Series s<0~(m-1)>_mjpeg_quant 1~5, 99, 100 Quality of JPEG video. 1 = worst quality, 5 = best quality. 100: Use the quality level in "qpercent" 99: Use the quality level in "qvalue"...
Page 254 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.9.1.1 Alternative video input profiles per channel In addition to the primary setting of video input, there can be alternative profile video input setting for each channel which might be for different scene of light (daytime or nighttime).
Page 255 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.10 IR cut control Group: ircutcontrol NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) mode auto, auto Set IR cut control mode day, night, schedule <boolean> Enable/disable Smart IR daymodebegintime 00:00~23:59...
Page 256 VIVOTEK URL commands for FD8367 URL Command Document for All Series sharpness -3 ~ 3, 100 Adjust sharpness of image according to mode settings. sharpnesspercent 0~100 Adjust sharpness of image by percentage. Softer 0 <-> 100 Sharper gammacurve 0~100 Gamma curve.
Page 257 VIVOTEK URL commands for FD8367 URL Command Document for All Series according to mode settings. profile_i0_sharpness -3~3,100 Adjust sharpness of image according to mode settings. profile_i0_sharpnessperce 0~100 Adjust sharpness value of percentage when sharpness=100 profile_i0_gammacurve 0~100 Gamma curve profile_i0_dnr_mode 3D noise reduction.
Page 258 VIVOTEK URL commands for FD8367 URL Command Document for All Series profile_i0_enable <boolean> Enable/disable this profile setting profile_i0_policy day, night The mode which the profile night, is applied to. schedule profile_i0_begintime hh:mm 18:00 Begin time of schedule mode. profile_i0_endtime hh:mm 06:00 End time of schedule mode.
Page 259 VIVOTEK URL commands for FD8367 URL Command Document for All Series win_i<0~2>_height 0 ~ 240 Height of motion detection window. win_i<0~2>_objsize 0 ~ 100 Percent of motion detection window. win_i<0~2>_sensitivity 0 ~ 100 Sensitivity of motion detection window. Group: motion_c<0~(n-1)> profile for m profile and n channel product (capability.nmotionprofile >...
Page 260 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.15 Tampering detection settings Group: tampering_c<0~(n-1)> for n channel product NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enable <boolean> Enable or disable tamper detection. duration 10 ~ 600 If tampering value exceeds the ‘threshold’ for more than ‘duration’...
Page 261 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.16.1 Express link Group:expresslink NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enable <boolean> Enable or disable express link. state onlycheck, badnetwork “onlycheck” : You have to input the onlyoffline, host name of your camera and press checkonline, "Register"...
Page 262 VIVOTEK URL commands for FD8367 URL Command Document for All Series forwarding 7.19 System log Group: syslog NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enableremotelog <boolean> Enable remote log. serverip <IP address> <blank> Log server IP address. serverport 514, 1025~65535 514 Server port used for log.
Page 263 Hyperlink of the logo vivotek.co logo_powerbyvvtk_hidden <boolean> 0 => display the power by vivotek logo 1 => hide the power by vivotek logo theme_option 1~3: One of the default themes. 4: Custom definition. theme_color_font string[7] #ffffff Font color...
Page 264 VIVOTEK URL commands for FD8367 URL Command Document for All Series theme_color_configbackground string[7] #323232 Background color of configuration area. theme_color_videobackground string[7] #565656 Background color of video area. theme_color_case string[7] #323232 Frame color custombutton_manualtrigger_s <boolean> Show or hide manual trigger (VI) button in homepage 0 ->...
Page 265 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.23 Capability Group: capability NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) 0/99 api_httpversion <string> 0300a The HTTP API version. 0/99 bootuptime <positive Server bootup time. integer> 0/99 Number of IR interfaces.
Page 266 VIVOTEK URL commands for FD8367 URL Command Document for All Series 0/99 naudiosetting <positive Number of audio settings integer> per channel. 0/99 nuart Number of UART <positive interfaces. integer> 0/99 nmotion 0, <positive Number of motion integer> window. 0/99 nmotionprofile 0, <positive...
Page 267 VIVOTEK URL commands for FD8367 URL Command Document for All Series 1(external) Bit 8 => Invalidate bit 1 ~ 7; 0(bit 1 ~ 7 are valid), 1(bit 1 ~ 7 are invalid) Bit 9 => Reserved bit; Invalidate lens_pan, Lens_tilt, lens_zoon, lens_focus, len_iris.
Page 268 VIVOTEK URL commands for FD8367 URL Command Document for All Series integer> simultaneous connections. 0/99 protocol_maxgenconnection <positive The maximum general integer> streaming connections . 0/99 protocol_maxmegaconnection <positive The maximum integer> megapixel streaming connections. 0/99 protocol_rtp_multicast_ <boolean> Indicate whether to scalable support scalable multicast.
Page 269 VIVOTEK URL commands for FD8367 URL Command Document for All Series videoin_codec <string> mjpeg, 0/99 Available codec of a h264 device. The sequence is not limited. videoin_c0_streamcodec <Positive 6,6,6 0/99 This equals Integer> "capability_videoin_c0 _streamcodec". videoin_c0_flexiblebitrate 0, 1 0/99 Support flexible bit rate control or not.
Page 270 VIVOTEK URL commands for FD8367 URL Command Document for All Series by commas> timeshift 0/99 <boolean> Indicate whether to support time shift caching stream. 0/99 audio_aec <boolean> Indicate whether to support acoustic echo cancellation. 0/99 audio_mic <boolean> Indicate whether to support built-in microphone input.
Page 271 VIVOTEK URL commands for FD8367 URL Command Document for All Series supported. 0: Not supported 1: Supported 0/99 camctrl_privilege <boolean> Indicate whether to support “Manage Privilege” of PTZ control in the Security page. 1: support both /cgi-bin/camctrl/camctrl. cgi and /cgi-bin/viewer/camctrl.c 0: support only /cgi-bin/viewer/camctrl.c...
Page 272 VIVOTEK URL commands for FD8367 URL Command Document for All Series support joystick control. 0/99 storage_dbenabled <boolean> Media files are indexed in database. 0/99 nanystream 0, <positive number of any media integer> stream per channel 0/99 <boolean> Indicate whether to...
Page 273 VIVOTEK URL commands for FD8367 URL Command Document for All Series 0/99 media_videoclip_maxlength <positive Maximum length integer> (second) of a videoclip. 0/99 media_videoclip_maxpreevent <positive Maximum duration integer> (second) after event occurred in a videoclip. localstorage_manageable <boolean> 0/99 Indicate whether manageable local storage is supported.
Page 274 VIVOTEK URL commands for FD8367 URL Command Document for All Series vadp <positive 0/99 An 32-bit integer, each integer> bit can be set separately as follows: Bit 0 => VADP interface Bit 1 => Capture video raw data Bit 2 => Support encode jpeg Bit 3 =>...
Page 275 VIVOTEK URL commands for FD8367 URL Command Document for All Series etailed,goo smart stream d,standard, medium,lo smartstream_supportmaxbitr 1Mbps,2M 0/99 Available maxbitrate <string> bps,4Mbps, of smart stream 6Mbps,8M bps,10Mbp s,20Mbps,3 0Mbps,40 Mbps version_genetec 1.0.2.3 0/99 <string> Indicate genetec version Group: capability_image_c<n>, where n = channel index from 0 ~ "capability_nvideoin"-1...
Page 276 VIVOTEK URL commands for FD8367 URL Command Document for All Series 1: Support remote focus 7.24 WebAPI: Information for a channel Group: capability_videoin_c<n>, n = channel index from 0 to "capability_nvideoin"-1 PARAMETER VALUE DEFAULT SECURITY DESCRIPTION (get/set) nmode <Positive 0/99 Indicate how many video modes Integer>...
Page 277 VIVOTEK URL commands for FD8367 URL Command Document for All Series mjpeg_maxbitrate <Positive 40000000 0/99 Maximum bitrates of MJPEG. Integer>, - The unit is bps. "-" means MJPEG does not support bit rate control. h264_ maxframerate A list of 0/99 Maximum fps that the device can <Positive...
Page 278 VIVOTEK URL commands for FD8367 URL Command Document for All Series binning 0, 1, 3 0/99 Indicate binning is used or not in this video mode. 0: No binning 1: 2x2 binning 3: 3x3 binning nresolution <Positive 0/99 How many resolution options in Integer>...
Page 279 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.26 Customized event script Group: event_customtaskfile_i<0~2> PARAMETER VALUE Default SECURITY DESCRIPTION (get/set) name string[40] NULL Custom script identification of this entry. date string[4-20] NULL Date of custom script. time...
Page 280 VIVOTEK URL commands for FD8367 URL Command Document for All Series 0, 1 Indicate the source id of di trigger. This field is required when trigger condition is “di”. One bit represents one digital input. The LSB indicates DI 0.
Page 281 VIVOTEK URL commands for FD8367 URL Command Document for All Series endtime hh:mm 24:00 End time of the weekly schedule. (00:00 ~ 24:00 sets schedule as always on) action_do_i<0~(ndo-1) 0, 1 Enable or disable trigger digital >_enable output. action_do_i<0~(ndo-1) 1~999 Duration of the digital output >_duration...
Page 282 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.28 Server setting for event action Group: server_i<0~4> PARAMETER VALUE DEFAULT SECURITY DESCRIPTION (get/set) name string[40] NULL Identification of this entry type email, email Indicate the server type: ftp, “email”...
Page 283 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.29 Media setting for event action Group: media_i<0~4> (media_freespace is used internally.) PARAMETER VALUE DEFAULT SECURITY DESCRIPTION (get/set) name string[40] NULL Identification of this entry type snapshot, snapshot Media type to send to the server or systemlog, store on the server.
Page 284 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.30 Recording Group: recording_i<0~1> PARAMETER VALUE DEFAULT SECURITY DESCRIPTION (get/set) name string[40] NULL Identification of this entry. enable 0, 1 Enable or disable this recording. priority 0, 1, 2...
Page 285 VIVOTEK URL commands for FD8367 URL Command Document for All Series weekday 0~127 Indicate which weekday is scheduled. One bit represents one weekday. bit0 (LSB) = Saturday bit1 = Friday bit2 = Thursday bit3 = Wednesday bit4 = Tuesday bit5 = Monday...
Page 286 VIVOTEK URL commands for FD8367 URL Command Document for All Series adaptive_preevent Indicate when is the adaptive recording started before the event trigger point (seconds) adaptive_postevent 0~10 Indicate when is the adaptive recording stopped after the event trigger point (seconds) Unit: Mega bytes.
Page 287 VIVOTEK URL commands for FD8367 URL Command Document for All Series localityname string[128] Asia The locality name in the certificate information. organizationname string[64] VIVOTEK Organization name in the Inc. certificate information. unit string[64] VIVOTEK Organizational unit name in the Inc.
Page 288 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.34 ePTZ setting Group: eptz_c<0~(n-1)> for n channel product. PARAMETER VALUE Default SECURITY DESCRIPTION (get/set) osdzoom <boolean> Indicates multiple of zoom in is “on-screen display” or not smooth <boolean>...
Page 289 VIVOTEK URL commands for FD8367 URL Command Document for All Series preset_i<0~19>_size <window size> <blank> Width and height of the preset. (It should be set by ePreset.cgi rather than by setparam.cgi.) 7.35 Exposure window setting per channel Group: exposurewin_c<0~(n-1)> for n channel products...
Page 290 VIVOTEK URL commands for FD8367 URL Command Document for All Series window. custom: Use inclusive and exclusive window. blc: Use BLC. i<0~(m-1)>_win_i<0~9 <boolean> Enable or disable the >_enable window. i<0~(m-1)>_win_i<0~9 0: Indicate exclusive. >_policy 1: Indicate inclusive. i<0~(m-1)>_win_i<0~9 <coordinate> 110,90 Left-top corner >_home...
Page 291 VIVOTEK URL commands for FD8367 URL Command Document for All Series 7.37 VIVOTEK Application Development Platform setting Group: vadp NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) version <string> 1.2.1.0 Indicate the VADP version. resource_total_memory <integer> <product Indicate total dependent> available memory size for VADP modules.
Page 292 VIVOTEK URL commands for FD8367 URL Command Document for All Series Group: vadp_module_i<0~(n-1)> NAME VALUE DEFAULT SECURITY DESCRIPTION (get/set) enable <boolean> Indicate if the module is enabled or not. If yes, also add the index of this module to the module_order.
Page 293 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8. Useful Functions 8.1 Drive the Digital Output Note: This request requires Viewer privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/dido/setdo.cgi?do1=<state>[&do2=<state>] [&do3=<state>][&do4=<state>] Where state is 0 or 1; “0” means inactive or normal state, while “1” means active or triggered state.
Page 294 VIVOTEK URL commands for FD8367 URL Command Document for All Series [di2=<state>]\r\n [di3=<state>]\r\n where <state> can be 0 or 1. Example: Query the status of digital input 1 . Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di1=1\r\n 8.3 Query Status of the Digital Output...
Page 295 VIVOTEK URL commands for FD8367 URL Command Document for All Series Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n do1=1\r\n 8.4 Capture Single Snapshot Note: This request requires Normal User privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/viewer/video.jpg?[channel=<value>][&resolution=<value>] [&quality=<value>][&streamid=<value>] If the user requests a size larger than all stream settings on the server, this request will fail.
Page 296 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.5 Account Management Note: This request requires Administrator privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/admin/editaccount.cgi? method=<value>&username=<name>[&userpass=<value>][&privilege=<value>] [&privilege=<value>][…][&return=<return page>] PARAMETER VALUE DESCRIPTION method Add an account to the server. When using this method, the “username”...
Page 297 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.6 System Logs Note: This request require Administrator privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/admin/syslog.cgi Server will return the most up-to-date system log. Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: <syslog length>\r\n \r\n <system log information>\r\n...
Page 298 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.8 ePTZ Camera Control Note: This request requires camctrl privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/camctrl/eCamCtrl.cgi?channel=<value>&stream=<value> [&move=<value>] – Move home, up, down, left, right [&auto=<value>] – Auto pan, patrol [&zoom=<value>] – Zoom in, out [&zooming=<value>&zs=<value>]...
Page 299 VIVOTEK URL commands for FD8367 URL Command Document for All Series zoom wide Zoom larger view with current speed. tele Zoom further with current speed. zooming wide or tele Zoom without stopping for larger view or further view with zs speed, used for joystick control.
Page 300 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.9 ePTZ Recall Note: This request requires camctrl privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/camctrl/eRecall.cgi?channel=<value>&stream=<value>& recall=<value>[&return=<return page>] PARAMETER VALUE DESCRIPTION channel <0~(n-1)> Channel of the video source. stream <0~(m-1)> Stream. recall Text string less than One of the present positions to recall.
Page 301 VIVOTEK URL commands for FD8367 URL Command Document for All Series relative path according to the current path. 8.11 IP Filtering Note: This request requires Administrator access privileges. Method: GET/POST Syntax: http://<servername>/cgi-bin/admin/ipfilter.cgi? method=<value>&[start=<ipaddress>&end=<ipaddress>][&index=<value>] [&return=<return page>] PARAMETER VALUE DESCRIPTION method addallow Add allowed IP address range to the server.
Page 302 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.11.1 IP Filtering for ONVIF Syntax: <product dependent> http://<servername>/cgi-bin/admin/ipfilter.cgi?type[=<value>] http://<servername>/cgi-bin/admin/ipfilter.cgi?method=add<v4/v6>&ip=<ipaddress>[&index=<val ue>][&return=<return page>] http://<servername>/cgi-bin/admin/ipfilter.cgi?method=del<v4/v6>&index=<value>[&return=<retu rn page>] PARAMETER VALUE DESCRIPTION type NULL Get IP filter type allow, deny Set IP filter type...
Page 303 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.12 Event/Control HTTP Tunnel Channel Note: This request requires Administrator privileges. Method: GET and POST Syntax: http://<servername>/cgi-bin/admin/ctrlevent.cgi ------------------------------------------------------------------------- GET /cgi-bin/admin/ctrlevent.cgi x-sessioncookie: string[22] accept: application/x-vvtk-tunnelled pragma: no-cache cache-control: no-cache ------------------------------------------------------------------------- POST /cgi-bin/admin/ ctrlevent.cgi...
Page 304 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.13 Get SDP of Streams Note: This request requires Viewer access privileges. Method: GET Syntax: http://<servername>/<network_rtsp_s<0~m-1>_accessname> “m” is the stream number. “network_accessname_<0~(m-1)>” is the accessname for stream “1” to stream “m”. Please refer to the “subgroup of network: rtsp”...
Page 305 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.15 Storage managements Note: This request requires administrator privileges. Method: GET and POST Syntax: http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=<cmd_type>[&<parameter>=<value>…] The commands usage and their input arguments are as follows. PARAMETER VALUE DESCRIPTION cmd_type <string>...
Page 306 VIVOTEK URL commands for FD8367 URL Command Document for All Series isLocked <boolean> Optional. Indicate if the file is locked or not. 0: file is not locked. 1: file is locked. A locked file would not be removed from UI or cyclic storage.
Page 307 VIVOTEK URL commands for FD8367 URL Command Document for All Series Command: update PARAMETER VALUE DESCRIPTION label <integer primary key> Required. Identify the designated record. Ex. label=1 isLocked <boolean> Required. Indicate if the file is locked or not. Ex. Update records whose key numbers are 1 and 5 to be locked status.
Page 308 VIVOTEK URL commands for FD8367 URL Command Document for All Series Subgroup of stormgr: i<0~(n-1)>: n is the total number of displayed records. Element name Type Description label <Integer Primary Key> A unique integer. triggerType <Text> Indicate the event trigger type.
Page 309 VIVOTEK URL commands for FD8367 URL Command Document for All Series 12:00:00</triggerTime> <triggerTime>2009-01-24 <backup>0</backup> </i0> <i1> <label>2</label> <triggerType>di</triggerType> <mediaType>snapshot</mediaType> <destPath>/mnt/auto/NCMF/123/123.jpg</destPath> <resolution>800x600</resolution> <isLocked>0</isLocked> 12:01:00</triggerTime> <triggerTime>2009-01-24 <backup>0</backup> </i1> </stormgr> Ex. Local storage status in XML format. <?xml version="1.0" encoding="ISO-8859-1" ?> <stormgr version="0.0.0.1">...
Page 310 VIVOTEK URL commands for FD8367 URL Command Document for All Series retType xml or javascript Optional. Ex. retype=javascript The default return message is in XML format. Ex. Query local storage status and call for javascript format return message. http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=queryStatus&retType=javascript There are two cgi commands for download and composing jpegs to avi format.
Page 311 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.16 Virtual input Note: Change virtual input (manual trigger) status. Method: GET/POST Syntax: http://<servername>/cgi-bin/admin/setvi.cgi?vi0=<value>[&vi1=<value>][&vi2=<value>] [&return=<return page>] PARAMETER VALUE DESCRIPTION vi<num> state[(duration)nstate] Ex: vi0=1 Setting virtual input 0 to trigger state Where "state"...
Page 312 VIVOTEK URL commands for FD8367 URL Command Document for All Series The resource is unavailable, ex. Virtual input is waiting for next state. Examples: 1. setvi.cgi?vi0=0(15000)1 2. setvi.cgi?vi0=1 Request 2 will not be accepted during the execution time(15 seconds). 8.17 Open Timeshift Stream (timeshift_enable=1, timeshift_c<n>_s<m>_allow=1)
Page 313 VIVOTEK URL commands for FD8367 URL Command Document for All Series request. Ex: Request the streaming from 12:20 rtsp://10.0.0.1/live.sdp?maxsft=10&reftime=12:30 forcechk Check if the requested stream enables timeshift, feature and if minsft is achievable. If false, return “415 Unsupported Media Type”.
Page 314 VIVOTEK URL commands for FD8367 URL Command Document for All Series mjpeg_quant 0, 1~5 Quality of JPEG video. 99, 1~5 0,99 is the customized manual <product dependent> input setting. 1 = worst quality, 5 = best quality. <product dependent> mjpeg_qvalue...
Page 315 VIVOTEK URL commands for FD8367 URL Command Document for All Series h264_intraperiod 250, 500, 1000, 2000, 3000, 1000 Intra frame period in 4000 milliseconds. h264_ratecontrolmode cbr, vbr, smart cbr: constant bitrate vbr: fix quality smart: smart stream h264_quant 0, 1~5...
Page 316 VIVOTEK URL commands for FD8367 URL Command Document for All Series i<0~2>_size window. 8.19 Export Files Note: This request requires Administrator privileges. Method: GET Syntax: For daylight saving time configuration file: http://<servername>/cgi-bin/admin/exportDst.cgi For language file: http://<servername>/cgi-bin/admin/export_language.cgi?currentlanguage=<value> PARAMETER VALUE DESCRIPTION currentlanguage 0~20 Available language lists.
Page 317 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.20 Upload Files Note: This request requires Administrator privileges. Method: POST Syntax: For daylight saving time configuration file: http://<servername>/cgi-bin/admin/upload_dst.cgi Post data: filename =<file name>\r\n \r\n <multipart encoded form data>...
Page 318 VIVOTEK URL commands for FD8367 URL Command Document for All Series 8.21 Media on demand Media on demand allows users to select and receive/watch/listen to metadata/video/audio contents on demand. Note: This request requires Viewer access privileges. Syntax: rtsp://<servername>/mod.sdp?[&stime=<value>][&etime=<value>][&length =<value>][&loctime =<value>][&file=<value>][&tsmode=<value>]...
Page 319: Technical Specifications
Compatible Accessories Mounting Kits AM-215 AM-712 L shape bracket Conduit box All specifications are subject to change without notice. Copyright © VIVOTEK INC. All rights reserved. Distributed by: Ver 1.3 VIVOTEK INC. VIVOTEK USA VIVOTEK Europe 6F, No.192, Lien-Cheng Rd., Chung-Ho,...
Page 320 Compatible Accessories Mounting Kits AM-215 AM-712 L shape bracket Conduit box All specifications are subject to change without notice. Copyright © VIVOTEK INC. All rights reserved. Distributed by: Ver 1.3 VIVOTEK INC. VIVOTEK USA VIVOTEK Europe 6F, No.192, Lien-Cheng Rd., Chung-Ho,...
Page 321: Technology License Notice
VIVOTEK Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE� THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE, OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOSES� FOR MORE INFORMATION, PLEASE REFER TO HTTP://WWW.VIALICENSING.COM�...
Page 322 取扱説明書に従って正しい取り扱いをして下さい Liability VIVOTEK Inc� cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice� VIVOTEK Inc� makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for any particular purpose�...

This manual is also suitable for:

Fd8367-v Fd8167 Fd8367-tv

Vivotek FD8167-T User Manual

Quick Links

Related Manuals for Vivotek FD8167-T

Summary of Contents for Vivotek FD8167-T

This manual is also suitable for:

Table of Contents