Parameter List; Fault Codes - Siemens Simovert P 6SE21 Series Operating Instructions Manual

SIMOVERT P 6SE21 Series Inverters

7.2 Parameter List

Parameter Description
P00 Frequency, output current or fault code
P01 Low frequency voltage boost
P02 Ramp–up time to maximum frequency
P03 Ramp–down time from maximum frequency
P04 Frequency control mode selection
P05 RUN/STOP mode
P06 Voltage to frequency curve selection
P07 Minimum frequency
P08 Maximum frequency
P09 Digital frequency setpoint adjustment
P10 Analogue frequency setpoint adjustment
P11 DC injection braking
P12 Jog
P13 Slip compensation
P14 Display status / Analogue output
P15 Voltage to frequency relationship: knee point
P16 Voltage to frequency relationship: curve type
P17 Current limit
P18 Overload limit
P19 Automatic boost
P20 Serial interface selection
P21 Serial interface address
P22 Serial interface parity and baud rate
P23 Digital input response speed
P24 Fixed frequency mode selection
P25 First fixed frequency
P26 Second fixed frequency
P27 Third fixed frequency
P28 Fourth fixed frequency
P29 Skip frequency
P30 Tachometer mode
P31 Tachometer scale factor
P32 Feedback compensation: proportional term
P33 Feedback compensation: integral term
P34 Feedback compensation: differential term
P35 Tachometer slip limit
P36 Tachometer sample rate
P37 Display tachometer frequency reading
P40 Switching frequency select
P41 Parameter default values
P42 Auto reset mode
P43 Ramp smoothing
P44 Tachometer Interface Unit
P45 Clear Text Operator Panel language
P48 Fault code
P49 Hardware type
P50 Software version
P51 Customer–specific variants
P52 Current monitor scaling factor

7.3 Fault Codes

Code Meaning
F00 Excessive load current or excessive link voltage. Low line voltage (6SE21**–3AA21 only).
F01 Excessive heatsink temperature.
F02 Corruption of parameterisation data in the non–volatile memory.
F03 Faulty operation of A–D converter or excessive tachometer feedback voltage.
F04 P07 set to a higher value than P08.
F05 P09 outside the limits set by P07 and P08.
F06 Fault on control board.
F07 Value of P25 > P08 setting or < P07 setting.
F08 Value of P26 > P08 setting or < P07 setting.
F09 Value of P27 > P08 setting or < P07 setting.
F10 Value of P28 > P08 setting or < P07 setting.
F11 Inverter tripped externally via X11.4 input.
Siemens plc 1995
Operating Instructions
Value Range Default Settings
[ ] – N. America Only
00.0 – 30.0% 00.0
00.0 – 400 s 10.0
00.0 – 400 s 10.0
000 – 009 000
000 – 009 000
000 – 006 000
00.0 – 399 Hz 00.1
00.1 – 400 Hz 50.0
00.0 – 400 Hz 50.0
080 – 240% 100
00.0 – 20.0% 00.0
00.1 – 400 Hz 05.0
00.0 – 20.0 00.0
000 – 003 000
00.1 – 400 Hz 50.0
000 or 001 000
00.1 – rated output 1.1 x
01.0 – 03.0 01.5
000 – 003 000
000 – 003 000
000 – 030 000
000 – 008 000
000 or 001 000
000 – 002 000
00.0 – 400 00.0
00.0 – 400 00.0
00.0 – 400 00.0
00.0 – 400 00.0
00.0 – 400 00.0
000 – 004 000
00.1 – 999 50.0
000 – 999% 050
000 – 250% 000
000 – 250% 000
00.0 – 20.0 Hz 05.0
001 – 200 001
000 – 400 n/a
000 – 002 002
000 or 001 000
000 – 002 000
000 – 100% 000
000 – 004 000
000 or 001 n/a
000 – 011 n/a
000 – 255 000
001 – 200% 100
G85139–A1615–U156–A
English
[001]
[60.0]
[60.0]
[60.0]
[001]
35
02.95