Table of Contents
Advertisement
Menu Configuration—MAIN MENU
For the operation procedure, see page 7.
Operation guide
Shows the buttons for
each operation.
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
NOTE
Setting of "MARKER SELECT" and "R-MARKER SELECT"
The setting values and features are as follows.
OFF: "MARKER SELECT" and "R-MARKER SELECT" do not function.
LINE: Displays the area with an outline.
HALF: The area outside the specified aspect ratio of the screen is displayed as 50% transparency.
HALF+L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area outside
of that is displayed as 50% transparency.
BLK.: The area outside the specified aspect ratio of the screen is black. Only the portion of the picture within
the designated area is displayed.
BLK. +L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area outside
of that becomes black so that only the area inside the line is displayed.
PICTURE IMPROVEMENT
Setting for the picture quality
Item
To do
APERTURE
Select the frequency of the luminance signal compensated in
FREQ.*
1
"APERTURE LEVEL."
APERTURE
Compensate the frequency response of the luminance signal of the
LEVEL*
1
video signal.
CTI
Adjust the clearness of the outlines of the chrominance signal.
LTI
Adjust the clearness of the outlines of the luminance signal.
sub menu
Display the sub menu which enables you to adjust the items of "PICTURE IMPROVEMENT" while
viewing the actual picture.
reset
Restore the default settings for all the items in "PICTURE IMPROVEMENT."
BACK LIGHT
Setting value: –20 – +20
Adjusts the brightness of the display.
DVI INPUT SEL.
Setting value: AUTO, MODE1, MODE2
When "AUTO" is selected, the format of signals come in to the DVI-D (HDCP) terminal is automatically
recognized. (Normally, select "AUTO.")
• Select "MODE1" or "MODE2" when the picture is not displayed correctly with "AUTO."
• DVI-D input of the monitor is compatible with HDCP.
1
AREA MARKER*
Setting for area marker functions
Item
To do
2
MARKER SELECT*
Select the style of the area marker.
ASPECT SELECT*
2
Select the aspect ratio of the area marker.
SAFETY MARKER*
3
Adjust the area of the safety marker.
R-MARKER SELECT*
2
Select the style of the area marker.
R-ASPECT SELECT*
2
Select the aspect ratio of the area marker.
R-SAFETY MARKER*
3
Adjust the area of the safety marker.
• The area marker or the safety marker is displayed by using AREA MARKER or SAFETY MARKER button, or
external control.
• Select either non-"R-" items or "R-" items to activate by using external control (☞ "External Control" on page
14).
• When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.
• To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker.
1
*
Memorized for each input.
2
*
Displayed only when picture is displayed in 16:9 aspect ratio.
*
3
Not displayed when picture is displayed in the 1:1 mode.
10
Setting value
OFF, LOW, HIGH
01 – 10
OFF, NORMAL, HARD
OFF, NORMAL, HARD
Setting value
☞ "NOTE"
4:3, 14:9, 13:9, 2.35:1, 1.85:1, 1.66:1
OFF, 80% – 100%
☞ "NOTE"
4:3, 14:9, 13:9, 2.35:1, 1.85:1, 1.66:1
OFF, 80% – 100%
Advertisement
Table of Contents
