JVC DT-V17L2D Instructions Manual page 14

Operation guide
Shows the buttons for
each operation.
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
NOTE
Setting of "CHARACTER SET."
Assign a name for each video source following the steps below.
1
Change the input to one that you want to assign a video source name for.
2
Select "CHARACTER SET."
3
Press buttons to select the first character.
• Each time you press button, the character changes as follows. Press
Space
4
Press button to move the arrow to the next.
• The characters entered before moving the arrow are memorized.
5
Repeat steps 3 and 4 (10 characters at maximum).
6
Press MENU button to store the name.
REMOTE SETTING
Setting for the external control
Item
SERIAL TYPE
PARALLEL TYPE
PIN1, PIN2, PIN3,
PIN4, PIN5
INFORMATION
Setting for the information display of the monitor
Item
POSITION
SOURCE ID
CHARACTER SET.*
STATUS DISPLAY
CRC ERROR
SUB HOUR METER
MODEL
VERSION
HOUR METER
1
* Memorized for each input.
CONTROL LOCK
Turns on (or off) the control lock function to disable the buttons on the front panel.
• The following operations are available even when this function is activated.
– Turning on/off (on standby) the monitor
– Displaying the SET-UP MENU (by pressing
to "OFF"
– Operating the monitor by an external control
If you try other operations, "
all reset
Restores all the settings and adjustments of the monitor to the default.
• "HOUR METER" and the settings done by using the adjustment knobs on the front panel will not be reset.
button to reverse the order. • When you operate the monitor with the AC power supply, the monitor is turned off (on standby) then turned
on automatically. When you operate the monitor with the DC 12 V power supply, the monitor is turned off (on
standby).
(☞ "External Control" on pages 14 and 15)
To do
Select the input terminal used for external control by
serial communication.
Select the external control method for the MAKE/
TRIGGER terminal.
Assign the control functions to the pins of the MAKE/
TRIGGER terminal.
• Assign a function to each pin terminal by selecting
"SET" in "PARALLEL TYPE." (The functions are
assigned for "PIN6" – "PIN8" and you cannot
change the assignment of these functions.)
To do
Select the position to show the information display (☞ "About the
Information Display" on page 7).
Select if the name assigned in "CHARACTER SET." is displayed on
the screen (☞ "About the Information Display" on page 7).
1 Assign a name to each video source as you like (10 characters at
maximum). You can also enter a name using the RS-232C system.
Select if the status of the current input and the setting of muting are
displayed on the screen (☞ "About the Status Display" on page 7).
Select if the CRC error indication for the input HD SDI signal is
displayed on the screen (☞ "About the Information Display" on page
7).
Display the hours of use (unit: hour). You can reset this item.
Display the model name of the monitor.
Display the version of the monitor.
Display the total hours of use (unit: hour). This item is used for maintenance of the monitor. You
cannot reset this item.
Setting value: OFF, ON
button while pressing
Control lock on!" appears on the screen.
Setting value
RS232C, RS485
MAKE, TRIGGER, SET
COLOR OFF, ASPECT, A.MARKER,
S.MARKER, TIME CODE, 1:1, SCR
CHECK, I/P MODE, SDI 1, SDI 2, DVI,
COMPONENT, VIDEO, TALLY SEL,
SOURCE ID, MUTING, MARK.SEL,
L.METER, STATUS, – – – (no function)
Setting value
UPPER, LOWER
OFF, ON
☞ "NOTE"
AUTO, OFF, ON
OFF, ON
button) and turning "CONTROL LOCK"
13
ENGLISH