Denon AVP-A1HDCI Owner's Manual page 44

_@(to_
The ZONE4 operations cannot be performed when set to "Rec
Select".
-NtO-
• When using the 2-way remote control unit. connect to the Port t
RS-232C connector.
.If GUI menu "Manual Setup" - "Option Setup" - "2Way Remote"is
set to "Used". you cannot use port' of the RS-232C terminal for the
external controller.
II
• When changing the remote 10. also change the AMP. iPod. TU and
NET/OTU modes of the main remote control unit at the same time
(aarpage 76).
• When changing the remote 10. also change the sub remote control
unit at the same time (aarpage 81).
[Selectable items]
iiti1
!~I
•
W hen using a 2-way remote control unit (RC-7000CI and RC-7001RCI.
sold separately). set this to "Used".
The Transducer Setup can be accessed through GUI menu "Speaker
Setup" - "Subwoofer Setup" is '" SP", "2SP UR" or "2SP MIX". The
transducer signal is outputted from "SW3".
This is effective when the "MAIN ZONE" has been set to "ON" for
the "Setting with Respect to the Zone" and the input source which is
set to "ON" has been selected for the" Setting with Respect to the
Input Source" .
Setting with Respect to the Monitor
When the HOMI monitor set to on is selected. the trigger out turns
on.
Set the transducer level.
Level
.
~ :
Turn the transducer output off.
Set the upper limit of the low frequency output to the transducer.
LPF
,.
When you adjust "Level", the adjusted value is set for all surround
modes. To adjust the level for individual surround modes, use "Channel
Level" (aarpage 72).
Associated with respect to the input source for zones set to "ON" at
"Setting with Respect to the Zone".
When the input source set to on is selected. the trigger out turns on.
Setting with Respect to the Zone
When the power of the zone turned on/off, the trigger out turns on.
Setting with Respect to the Input Source
Setting with Respect to the Surround Mode
This is effective when the "MAIN ZONE" has been set to "ON" for
the "Setting with Respect to the Zone" and the input source which is
set to "ON" has been selected for the "Setting with Respect to the
Input Source".
When the surround mode set to on is selected, the trigger out turns
on.
ti
-~:
•
41
_@(to_
The ZONE4 operations cannot be performed when set to "Rec
Select".
-NtO-
• When using the 2-way remote control unit. connect to the Port t
RS-232C connector.
.If GUI menu "Manual Setup" - "Option Setup" - "2Way Remote"is
set to "Used". you cannot use port' of the RS-232C terminal for the
external controller.
II
• When changing the remote 10. also change the AMP. iPod. TU and
NET/OTU modes of the main remote control unit at the same time
(aarpage 76).
• When changing the remote 10. also change the sub remote control
unit at the same time (aarpage 81).
[Selectable items]
iiti1
!~I
•
W hen using a 2-way remote control unit (RC-7000CI and RC-7001RCI.
sold separately). set this to "Used".
The Transducer Setup can be accessed through GUI menu "Speaker
Setup" - "Subwoofer Setup" is '" SP", "2SP UR" or "2SP MIX". The
transducer signal is outputted from "SW3".
This is effective when the "MAIN ZONE" has been set to "ON" for
the "Setting with Respect to the Zone" and the input source which is
set to "ON" has been selected for the" Setting with Respect to the
Input Source" .
Setting with Respect to the Monitor
When the HOMI monitor set to on is selected. the trigger out turns
on.
Set the transducer level.
Level
.
~ :
Turn the transducer output off.
Set the upper limit of the low frequency output to the transducer.
LPF
,.
When you adjust "Level", the adjusted value is set for all surround
modes. To adjust the level for individual surround modes, use "Channel
Level" (aarpage 72).
Associated with respect to the input source for zones set to "ON" at
"Setting with Respect to the Zone".
When the input source set to on is selected. the trigger out turns on.
Setting with Respect to the Zone
When the power of the zone turned on/off, the trigger out turns on.
Setting with Respect to the Input Source
Setting with Respect to the Surround Mode
This is effective when the "MAIN ZONE" has been set to "ON" for
the "Setting with Respect to the Zone" and the input source which is
set to "ON" has been selected for the "Setting with Respect to the
Input Source".
When the surround mode set to on is selected, the trigger out turns
on.
ti
-~:
•
41